ViewSonic PA700X User guide

PA700S_PA700X_PA700W

PS502X_PS502W

DLP Projector

User Guide

Model No. VS19341 | VS19343 | VS19342 | VS19344 | VS19345

P/N: PA700S | PA700X | PA700W | PS502X | PS502W

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in

a safe manner, as well as registering your product for future service. Warranty information contained in this User

Guide will describe your limited coverage from ViewSonic® Corporation, which is also found on our web site at

http://www.viewsonic.com in English, or in specific languages using the Regional selection box of our website.

2

Thank you for choosing ViewSonic®

As a world-leading provider of visual solutions, ViewSonic® is dedicated to

exceeding the world’s expectations for technological evolution, innovation, and

simplicity. At ViewSonic®, we believe that our products have the potential to make

a positive impact in the world, and we are confident that the ViewSonic® product

you have chosen will serve you well.

Once again, thank you for choosing ViewSonic®!

3

Safety Precauons

Please read the following Safety Precauons before you start using the projector.

• Keep this user guide in a safe place for later reference.

• Read all warnings and follow all instrucons.

• Allow at least 20“ (50 cm) clearance around the projector to ensure proper

venlaon.

• Place the projector in a well-venlated area. Do not place anything on the

projector that prevents heat dissipaon.

• Do not place the projector on an uneven or unstable surface. The projector may

fall over, causing personal injury or projector malfuncon.

• Do not look straight at the projector lens during operaon. The intense light

beam may damage your eyes.

• Always open the lens shuer or remove the lens cap when the projector lamp is

on.

• Do not block the projecon lens with any objects when the projector is under

operaon as this could cause objects to become heated and deformed or even

cause a re.

• The lamp becomes extremely hot during operaon. Allow the projector to

cool for approximately 45 minutes prior to removing the lamp assembly for

replacement.

• Do not use lamps beyond the rated lamp life. Excessive use of lamps beyond the

rated life could cause them to break on rare occasions.

• Never replace the lamp assembly or any electronic component unless the

projector is unplugged.

• Do not aempt to disassemble the projector. There are dangerous high voltages

inside which may cause death if you should come into contact with live parts.

• When moving the projector, be careful not to drop or bump the projector on

anything.

• Do not place any heavy objects on the projector or connecon cables.

• Do not stand the projector on end vercally. Doing so may cause the projector to

fall over, causing personal injury or projector malfuncon.

• Avoid exposing the projector to direct sunlight or other sources of sustained

heat. Do not install near any heat sources such as radiators, heat registers,

stoves, or other devices (including ampliers) that may increase the temperature

of the projector to dangerous levels.

4

• Do not place liquids near or on the projector. Liquids spilled into the projector

may cause it to fail. If the projector does become wet, disconnect it from the

power supply and call your local service center to have the projector serviced.

• When the projector is under operaon, you may sense some heated air and odor

from its venlaon grill. It is a normal operaon and not a defect.

• Do not aempt to circumvent the safety provisions of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the

other. A grounding-type plug has two blades and a third grounding prong. The

wide and third blade are provided for your safety. If the plug does not t into

your outlet, obtain an adapter and do not aempt to force the plug into the

outlet.

• When connecng to a power outlet, DO NOT remove the grounding prong.

Please ensure grounding prongs are NEVER REMOVED.

• Protect the power cord from being treaded upon or pinched, parcularly at the

plug, and at the point where it emerges from the projector.

• In some countries, the voltage is NOT stable. This projector is designed to

operate safely within a voltage between 100 to 240 volts AC, but could fail if

power cuts or surges of ±10 volts occur. In areas where voltage may uctuate

or cut out, it is recommended that you connect your projector through a power

stabilizer, surge protector, or uninterruptable power supply (UPS).

• If smoke, an abnormal noise, or a strange odor is present, immediately switch

the projector o and call your dealer or ViewSonic®. It is dangerous to connue

using the projector.

• Use only aachments/accessories specied by the manufacturer.

• Disconnect the power cord from the AC outlet if the projector is not being used

for a long period of me.

• Refer all servicing to qualied service personnel.

CAUTION: Possibly hazardous opcal radiaon is emied from this product. As

with any bright light source, do not stare into the beam, RG2 IEC 62471-

5:2015.

5

Safety Precautions - Ceiling Mounting

Please read the following Safety Precautions before you start using the projector.

If you intend to mount the projector on the ceiling, it is strongly recommended

that you use a proper fitting projector ceiling mount kit and that you ensure it is

securely and safely installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the

projector may fall from the ceiling due to an improper attachment through the use

of the wrong gauge or length screws.

6

Contents

Safety Precautions ....................................................... 3

Introduction ................................................................ 9

Package Contents - PA700S | PA700X | PA700W ..................................................9

Package Contents - PS502X | PS502W .................................................................10

Product Overview .................................................................................................11

Projector ................................................................................................................ 11

Keypad ................................................................................................................... 12

Indicator Lights ...................................................................................................... 13

I/O Ports ................................................................................................................ 14

Remote Control ..................................................................................................... 15

Initial Setup ............................................................... 19

Choosing a Location - Projection Orientation .......................................................19

Projection Dimensions - PA700S | PA700X ..........................................................20

Projection Dimensions - PA700W ......................................................................... 22

Projection Dimensions - PS502X .................................................................... ....... 24

Projection Dimensions - PS502W .........................................................................26

Mounting the Projector ........................................................................................28

Using the Security Bar ..........................................................................................28

Making Connections .................................................. 29

Connecting to Power ............................................................................................29

Connecting to External Devices ............................................................................30

HDMI Connection .................................................................................................. 30

Audio Connection .................................................................................................. 31

USB Type A Connection ......................................................................................... 32

RS-232 Connection ................................................................................................ 33

PC/Notebook and Monitor Connection ................................................................ 34

Using the Projector .................................................... 35

Starting Up the Projector .................................................................... ..................35

Selecting an Input Source .....................................................................................36

Help Menu ............................................................................................................. 37

Adjusting the Projected Image .............................................................................40

Adjusting the Projector’s Height and Projection Angle ......................................... 40

Adjusting the Focus, Keystone, and Zoom ............................................................ 41

Shutting Down the Projector ................................................................................42

7

Operating the Projector ............................................. 43

On-Screen Display (OSD) Menu ............................................................................43

Menu Navigation ..................................................................................................44

On-Screen Display (OSD) Menu Tree .................................................................... 45

Menu Operation ...................................................................................................50

Image Menu .......................................................................................................... 50

Display Menu......................................................................................................... 52

Setup Menu ........................................................................................................... 55

Options Menu ....................................................................................................... 57

Appendix ................................................................... 60

Specifications - PA700 ..........................................................................................60

Specifications - PS502 ........................................................................................... 61

Projector Dimensions ...........................................................................................62

Timing Chart .........................................................................................................63

Analog RGB ............................................................................................................ 63

HDMI 3D ................................................................................................................ 65

Troubleshooting ...................................................................................................66

LED Indicators ........................................................................................................ 68

Maintenance.........................................................................................................69

General Precautions .............................................................................................. 69

Cleaning the Lens .................................................................................................. 69

Cleaning the Case .................................................................................................. 69

Storing the Projector ............................................................................................. 69

8

Regulatory and Service Information .......................... 70

Compliance Information ....................................................................................... 70

FCC Compliance Statement ................................................................................... 70

Industry Canada Statement ................................................................................... 70

CE Conformity for European Countries ................................................................. 71

Declaration of RoHS2 Compliance......................................................................... 72

Indian Restriction of Hazardous Substances ......................................................... 73

Product Disposal at End of Product Life ................................................................ 73

Copyright Information ..........................................................................................74

Customer Service .................................................................................................. 75

Limited Warranty .................................................................................................. 76

Mexico Limited Warranty ...................................................................................... 79

9

Introduction

Package Contents - PA700S | PA700X | PA700W

DLP Projector

PA700W Series

Quick Start Guide

http://vsweb.us/q/dn.php

http://vsweb.us

Download Link

ViewSonic Projector

1 2 3

4

5 6

Number Descripon

1 Projector

2Remote Control

3Baeries

4Quick Start Guide

5Power Cord

6VGA Cable

NOTE: The power cord and remote control included in your package may vary

depending on your country. Please contact your local reseller for more

informaon.

10

Package Contents - PS502X | PS502W

DLP Projector

PS502W Series

Quick Start Guide

http://vsweb.us/q/dn.php

http://vsweb.us

Download Link

ViewSonic Projector

1 2 3

4

5 6

Number Descripon

1 Projector

2Remote Control

3Baeries

4Quick Start Guide

5Power Cord

6VGA Cable

NOTE: The power cord and remote control included in your package may vary

depending on your country. Please contact your local reseller for more

informaon.

11

Product Overview

Projector

11

9

8

5 5

2 2

3 3

4

6 6

10

11

4

7

PA700 Series PS502 Series

Number Descripon

1 Vent (outlet)

2IR Receiver

3Keypad

4Focus Ring

5Vent (inlet)

6Projecon Lens

7Adjuster Foot

8Zoom Ring

9I/O Ports

10 AC IN

11 Security Lock

NOTE: Do not block projector intake and exhaust vents.

12

Keypad

MENU

EXIT

ENTER

SOURCE AUTO

Key Descripon

MENU

EXIT

ENTER

SOURCE AUTO

Power Toggles the projector between standby mode and

Power On.

MENU

EXIT

ENTER

SOURCE AUTO

MENU

EXIT

ENTER

SOURCE AUTO

Keystone

Manually corrects distorted images resulng from an

angled projecon when the On-Screen Display (OSD)

Menu is acvated.

tupq Navigaon

Selects the desired menu items and makes

adjustments when the On-Screen Display (OSD) Menu

is acvated.

MENU

EXIT

ENTER

SOURCE AUTO

Menu/Exit

• Acvate the On-Screen Display (OSD) Menu.

• Go back to previous level in the OSD Menu.

• Exit and save menu sengs.

MENU

EXIT

ENTER

SOURCE

AUTO

Source Toggle to the next input source.

MENU

EXIT

ENTER

SOURCE AUTO

Help Displays the Help menu.

MENU

EXIT

ENTER

SOURCE AUTO

Enter Conrm the selecon when the On-Screen Display

(OSD) Menu is acvated.

MENU

EXIT

ENTER

SOURCE

AUTOAuto Automacally synchronize the projector to the input

source.

13

Indicator Lights

Indicator Light Descripon

MENU

EXIT

ENTER

SOURCE AUTO

Power indicator light

MENU

EXIT

ENTER

SOURCE AUTO

Light source indicator light

MENU

EXIT

ENTER

SOURCE AUTO

Temperature indicator light

14

I/O Ports

HDMI 2

HDMI 1

USB 5V/1.5A

(SERVICE)

RS232

IN

COMPUTER

MONITOR OUT

OUT

AUDIO

1 2

3

45

6

7

8

9

Port Descripon

1 HDMI 1 HDMI port.

2 HDMI 2 HDMI port.

3 RS-232 RS-232 control port.

4USB (5V/1.5A Out)

(Service) USB Type A port for power and service.

5 COMPUTER RGB (PC) signal input socket.

6 MONITOR OUT RGB (PC) signal output socket.

7 AUDIO IN Audio signal input socket.

8 AUDIO OUT Audio signal output socket.

9 AC IN AC IN socket.

15

Remote Control

12

34

7

10

13

16

20

22

12

18

11

14

17

19

23

15

21

5

8

9

6

Buon Descripon

1AV Mute Hide and recover the screen picture and volume mute.

2Power Turns the projector On or O

3Auto Sync Automacally synchronize the projector to the input

source.

4Source Toggle to the next input source.

5Navigaon

Buons

Navigates and selects the desired menu items and

make adjustments when the On-Screen Display (OSD)

Menu is acvated.

6Enter Conrm the selecon when the On-Screen Display

(OSD) Menu is acvated.

7 Menu/Exit

• Turns the On-Screen Display (OSD) Menu On or O.

• Go back to a previous OSD Menu.

• Exit and Save menu sengs.

8Brightness Displays the brightness selecon bar.

9Volume Up Increase the volume level.

16

Buon Descripon

10 Keystone Manually correct distorted images.

11 Volume

Down Decrease the volume level.

12 Video Unsupported Buon

13 VGA Selects Computer IN port for display.

14 HDMI Selects the HDMI 1 or HDMI 2 input source.

15 Aspect Displays the format selecon bar.

16 Page Up

Operates your display soware program (on a

connected PC) which responds to page up commands

(like Microso PowerPoint).

NOTE: Only available when a PC input source is

selected and the PC and projector are connected

via USB.

17 Zoom In Increase the projected image size.

18 Freeze Freeze/un-freeze the projected image.

19 Zoom Out Reduce the projected image size.

20 Page Down

Operates your display soware program (on a

connected PC) which responds to page down

commands (like Microso PowerPoint).

NOTE: Only available when a PC input source is

selected and the PC and projector are connected

via USB.

21 Display Mode Displays the display mode selecon bar.

22 Mouse Mode Enable/Disable the mouse funcon.

23 Mute Mute/Unmute.

Using the Remote Control Mouse Mode and Page Up/Down Funcon

1. Connect the PC/Notebook to the projector via the COMPUTER and USB ports.

2. Set the input source to PC.

3. Now you can operate your display soware program which responds to page up/

down commands (like Microso PowerPoint).

17

Remote Control - Receiver Range

To ensure proper funcon of the remote control follow the steps below:

1. The remote control must be held at an angle within 30° perpendicular to the

projector’s IR remote control sensor(s).

2. The distance between the remote control and the sensor(s) should not exceed 10

m (32.8 .).

NOTE: Refer to the illustraon for the locaon of the infrared (IR) remote

control sensor(s).

Approx. 30° Approx. 30°

PS502 SeriesPA700 Series

18

Remote Control - Replacing the Baeries

1. Remove the baery cover from the boom of the remote control by pressing the

nger grip and sliding it across.

2. Remove any exisng baeries (if necessary) and install two AAA baeries.

NOTE: Observe the baery’s polaries as indicated.

3. Replace the baery cover by aligning it with the base and pushing it back into

posion.

NOTE:

• Avoid leaving the remote control and baeries in excessive heat or a humid

environment.

• Replace only with the same or equivalent type recommended by the

baery manufacturer.

• If the baeries are drained or if you will not be using the remote control for

an extended period of me, remove the baeries to avoid damage to the

remote control.

• Dispose of the used baeries according to the manufacturer’s instrucons

and local environment regulaons for your region.

19

Inial Setup

This secon provides detailed instrucons for the inial set up your projector.

Choosing a Locaon - Projecon Orientaon

Personal preference and room layout will decide the installaon locaon. Consider

the following:

• Size and position of your screen.

• Location of a suitable power outlet.

• Location and distance between the projector and other equipment.

The projector is designed to be installed in one of the following locations:

Locaon

Front Table

The projector is placed near

the oor in front of the screen.

Front Ceiling

The projector is suspended

upside-down from the ceiling

in front of the screen.

Rear Table¹

The projector is placed near

the oor behind the screen.

Rear Ceiling¹

The projector is suspended

upside-down from the ceiling

behind the screen.

¹ A rear projecon screen is required.

20

Projecon Dimensions - PA700S | PA700X

• 4:3 Image on a 4:3 Screen

NOTE:

• (e) = Screen

(f) = Center of Lens

4:3 Image on a 4:3 Screen

(a) Screen Size (b) Projecon Distance (c) Image

Height

(d) Vercal

Oset

Minimum Maximum

in. mm in. mm in. mm in. mm in. mm

30 762 46.56 1183 51.84 1317 18 457 2.70 69

60 1524 93.12 2365 103.68 2633 36 914 5.40 137

70 1778 108.64 2759 120.96 3072 42 1067 6.30 160

80 2032 124.16 3154 138.24 3511 48 1219 7.20 183

100 2540 155.20 3942 172.80 4389 60 1524 9 229

120 3048 186.24 4730 207.36 5267 72 1829 10.80 274

150 3810 232.80 5913 259.20 6584 90 2286 13.50 343

200 5080 310.40 7884 345.60 8778 120 3048 18 457

250 6350 388 9855 432 10973 150 3810 22.50 572

300 7620 465.60 11826 518.40 13167 180 4572 27 686

NOTE:

• These gures are for reference purposes only. Please refer to the actual

projector for the precise dimensions.

• It is recommended that if you intend to permanently install the projector

to physically test the projecon size and distance using the actual projector

before you permanently install it.

Page is loading ...

ViewSonic PA700X User guide

This manual is also suitable for

ViewSonic PA700X User guide

Related papers

Other documents