Page is loading ...
2023, 62913815/A
Joyn2
Platform
Developed by Vitra in Switzerland
Design: Vitra
Assembly instructions and instructions for use
2/60 2023, 62913815/A
EN
CONTENTS
Contents
1 Notes............................................................................................................................................... 3
1.1 Proper use ...................................................................................................................................... 3
1.2 Explanation of symbols ............................................................................................................... 3
2 Safety .............................................................................................................................................. 4
3 Principle for assembly .................................................................................................................. 5
3.1 Base assembly specifications .................................................................................................... 5
4 Specifications and restrictions for assembly and modification ........................................... 8
4.1 Requirements for an office desk ................................................................................................ 8
4.1.1 Full-fledged desk .......................................................................................................................... 8
4.1.2 Written material on a smaller scale .......................................................................................... 9
5 Assembly ....................................................................................................................................... 10
5.1 General assembly instructions .................................................................................................. 10
5.2 Overview of assembly sequence .............................................................................................. 12
2023, 62913815/A 3/60
NOTES
EN
1 Notes
Please read these instructions carefully before use. Keep them in a safe place for later refer-
ence. Assembly/dismantling may only be performed by qualified personnel. Check delivery
is complete before assembly.
Do not use parts that are not part of the system.
1.1 Proper use
The product has been designed for use as an table system.
The product must only be used in a commercial environment.
There is a danger of damage to property or personal injury if improperly used.
Please dispose of your product in accordance with the currently applicable regula-
tions in your country.
1.2 Explanation of symbols
Safety instructions are indicated in these instructions as follows.
CAUTION
Indicates a hazardous situation.
Failure to avoid such a situation may lead to injury.
NOTE
Indicates basic information and work recommendations.
NOTE
Indicates a reference to another instruction.
NOTE
Indicates that at least 2 people are required for the assembly step.
4/60 2023, 62913815/A
EN
SAFETY
2 Safety
CAUTION
Risk of injury and material damage due to incorrect assembly/disassembly.
The stability of the product is no longer guaranteed.
► Assembly/dismantling may only be performed by qualified personnel.
CAUTION
When moving the product, the following points must be strictly observed:
► At least two persons must be deployed to move it.
► Clear obstacles from the route.
► Disconnect power cable (if present) from the mains.
► Do not move when loaded; shelves/table tops must be cleared beforehand.
► Der Tisch darf nicht an der Tischplatte angehoben werden, da die Tischplattenbefes-
tigung ausreissen kann.
2023, 62913815/A 5/60
PRINCIPLE FOR ASSEMBLY
EN
3 Principle for assembly
3.1 Base assembly specifications
NOTE
Observe the permissible distance between the double-leg section and the outer edge
and between the double-leg sections.
CAUTION
If a platform has two different end plates, the intermediate table top must be at
least 1400 mm in size.
Otherwise, the stability of the platform is not guaranteed.
6/60 2023, 62913815/A
EN
PRINCIPLE FOR ASSEMBLY
NOTE
The maximum distance between two cross-connectors is 2400 mm. If the distance exceeds
2400 mm, the other cross-connector must always be placed in the middle.
NOTE
A cross-connector must be mounted under each technical rail end and technical rail joint.
Other cross-connectors that are required must be mounted as described.
2023, 62913815/A 7/60
PRINCIPLE FOR ASSEMBLY
EN
NOTE
An additional base must be mounted under each table top joint (see diagram).
NOTE
An additional base must be mounted in the centre if the table top is larger than 1600 mm.
8/60 2023, 62913815/A
EN
SPECIFICATIONS AND RESTRICTIONS FOR ASSEMBLY AND MODIFICATION
4 Specifications and restrictions for assembly and modifica-
tion
4.1 Requirements for an office desk
NOTE
If the dimensions of a configuration are at least equal to the specified masses, then the
requirements for an office desk according to EN527-1 are met.
4.1.1 Full-fledged desk
2023, 62913815/A 9/60
SPECIFICATIONS AND RESTRICTIONS FOR ASSEMBLY AND MODIFICATION
EN
4.1.2 Written material on a smaller scale
10/60 2023, 62913815/A
EN
ASSEMBLY
5 Assembly
5.1 General assembly instructions
Joyn 2 facilitates a variety of configuration options. Before use, it is necessary to familiarise
yourself with the individual components and their function as well as the limits of the table
arrangement.
The assembly instructions and instructions for use is an important document that the user
must observe.
To assemble your Joyn 2 Platform, you will need the following tools and aids.
2023, 62913815/A 11/60
ASSEMBLY
EN
12/60 2023, 62913815/A
EN
ASSEMBLY
5.2 Overview of assembly sequence
1 Profile connectors
2 Cross-connectors
3 Trestle
4 Base
5 End cap
6 Notes on mounting the cover
7 Technical rail
8 Table tops and end plates
9 Cover
10 Cable basket
1
2
3
4
5
6
7
8
9
8
10
8
8
8
9
2023, 62913815/A 13/60
ASSEMBLY
EN
1. Profile connector
14/60 2023, 62913815/A
EN
ASSEMBLY
2. Cross connector
2023, 62913815/A 15/60
ASSEMBLY
EN
16/60 2023, 62913815/A
EN
ASSEMBLY
3. Trestle
2023, 62913815/A 17/60
ASSEMBLY
EN
4. Table top support
18/60 2023, 62913815/A
EN
ASSEMBLY
NOTE
The base must be mounted as follows:
1) under each butt joint.
2) in the middle of the table top, for table tops larger than 1600 mm.
2023, 62913815/A 19/60
ASSEMBLY
EN
5. End caps
20/60 2023, 62913815/A
EN
ASSEMBLY
6. Notes on mounting the cover
NOTE
Before installing the cover holders on the technical rail and the table top, the position of
the individual covers must be noted. Accordingly, the holders must be pre-assembled.
/
