Coats Kit 85000805, Carrier Operating instructions

Brand: Coats

Model: Kit 85000805, Carrier

Type: Operating instructions

Parts List

Part No. Description

8185679 Clamp Carrier

8182279 1/2-13 UNC, Hex Link Bolt

903174 5100-75 Ext. Retaining Ring

8185035 0.512 ID x 0.787 OD x 0.079 Washer

8185018 5100-46 Ext. Retaining Ring

85000803 Packet Loctite®

Loctite® is a trademark of Henkel Corporation

Tools Required: Screwdriver, 15mm Combination

Wrench, Snap Ring Pliers, 3/4-inch Socket, 1/2-inch

Drive Ratchet, Dead Blow Hammer, 9/16-inch

Combination Wrench, Allen Wrench, Torque Wrench

Installation Instructions

Always DISCONNECT THE ELECTRICAL

POWER before servicing equipment. This

prevents electrical shock or accidental

movement of the systems operated by the

electrical power.

Always DISCONNECT AIR SUPPLY before

servicing equipment. This prevents acciden-

tal movement of systems operated by com-

pressed air which may result in personal

injury. BLEED THE AIR SYSTEM by actuating

all the valves.

1. Before beginning any work, clear the area, position

clamps in outer position, and rotate table top for easy

access to the carriers. Disconnect all power sources,

both air and electricity inputs. Allow any stored air in the

reservoir to escape by depressing the inflate pedal.

2. Verify the stored air pressure is zero by observing

the air pressure gauge on top of the tower.

3. Disconnect

air line at carri-

er’s elbow fit-

ting. Repeat on

opposite side.

4. Loosen and then remove the four table top hose

holders. If necessary, remove air hose and use screw-

driver to provide leverage when loosening hose holder.

5. Remove outer retaining rings and washers from

both cylinder mounting shafts. Slide the cylinders off.

6. Next, remove the inner retaining ring that holds the

cylinder mounting shaft on the carrier and slide the

cylinder mounting shaft out.

7. Loosen and remove the table top link bolt to

remove the old carrier assembly.

CAUTION

Carrier Kit 85000805

For use with COATS Model

APX Series Tire Changers

Hennessy Industries • 1601 J.P. Hennessy Drive, LaVergne, TN 37086-3565 (800) 688-6359 • (615) 641-7533 • (615) 641-5104 FAX • www.ammcoats.com

Inner Retaining Ring

Outer Retaining

Ring & Washer

Outer

Retaining

Ring &

Washer

Table Top

Link Bolt

Cylinder Mounting Shaft

Air Line At

Elbow Fitting

Hose

Holder

8. Use slight force to pull carrier assembly off table

top. Remove slide stopper screws and lift off slide.

9. Remove clamp, clamp button and air fitting from

old carrier and install them on the new carrier. Press

large button in and move clamp to outer position. Press

and hold large button and with a small screwdriver,

press back of button through small hole in clamp; then

slide clamp off clamp carrier.

10. Next, install slide stopper onto new carrier

assembly. Position slide at an angle on carrier and,

using a dead blow hammer, drive slide onto carrier so

that it passes the carrier’s ridge stop.

11. Install new carrier assembly and the slide stop-

per screws on the table top.

12. Apply loctite to the table top link bolt and install

new carrier assembly to the tabletop.

Note: Using a torque wrench, tighten the bolt holding

the carrier to 25-35 ft. pounds torque.

13. Repeat steps 6 - 12 for opposite side carrier

assembly.

14. Reassemble remaining components in reverse

order.

15. Functional test machine.

Carrier’s

Ridge Stop

Angle Slide

On Carrier

PUSH

Remove Clamp

Table Top

Link Bolt

Coats Kit 85000805, Carrier Operating instructions

Coats Kit 85000805, Carrier Operating instructions

Coats Kit 85000805, Carrier Operating instructions

Related papers

Other documents