2. LAMONA
  3. LAM8702

LAMONA LAM8702 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the LAMONA LAM8702 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Installation Instructions
Washing Machine
(To be used in conjunction with User Instructions)
l
Please read these Installation Instructions to ensure safe,
correctttingofthisappliance.
l
Thewashingmachineshouldbettedbyasuitablycompetent,
qualiedperson.
l
Pleasekeeptheseinstructionsinasafeplaceforfuturereference.
l
Dangerofsuffocationkeeppackagingmaterialawayfromchildren.
LAM8702/03
Warning for hazardous
situations with regard to
lifeandproperty.
Warning for
electricshock.
Warning for
riskofre.
Throughout this manual the
followingsymbolsareused.
2
10mmopen
endedspanner
Flat and
cross head
screw drivers
DO NOT use high
speedimpact
powertools.
www.howdens.com
Safety Information
Installation
Tools required
Twopersonlift. Riskofinjury:
Bewareofsharpmetal
edges.Usegloveswhen
handling.
NOTE:Iftheelectricity
cable is damaged it
mustbereplacedbya
competentperson.
Washing machine must
bexedsecurelyand
level.
Risk of damage to
property:
Take care of surrounding
area when moving the
appliancetoprevent
damagetoooring,wall
coverings,pipesetc..
Ensurethatallpacking
andtransitprotectors
have been removed
fromtheappliance
beforepositioning.
DO NOT PUSH
against the washing
machinefasciapanel.
Thisapplianceisnot
designed for stacking
withotherappliances.
3
B(3x15mm)
A(4.5x10)
x2
x1
x2 x2 x5
x1
www.howdens.com
1. Remove transit POLY BLOCK..........................p.4
2. Removetransitbolts...........................................p.4
3. Dimensions..........................................................p.5
4. Fitfascialletandanti-tiltsupport....................p.5
5. Preparethedécordoor.......................................p.6
6. Washing machine connections..........................p.7
7. Connecting water hose.......................................p.8
8. Positioning the washing machine......................p.9
9. Fitdécordoorandmagneticcatches...............p.10
10. Raise and level the machine..............................p.11
11.Drainhoseandlter............................................p.12
12. Plinth.....................................................................p.12
Parts supplied
Fitting guide
Copyright©2018HowdenJoineryLtd.Allrightsreserved.
4
IMPORTANT:
REMOVE POLY BLOCK.
10mmopen
endedspanner
www.howdens.com
1 - Remove transit item
2 - Remove transit bolts
5
Position the washing machine
relativetoserviceconnections.
Décor fillet
can be added
Example
nominal
set-up
Min 5mm
Max 15mm
Anti-tilt block
45-50mm
*25mm
Approx 830mm
*At nominal set up -
165mm from floor to the
base of cabinet.
min
15mm
817mm-
831mm
554mm
597mm
820-920mm
min
575mm
*600mm
www.howdens.com
3 - Dimensions
4 - Fit décor llet and anti-tilt block
*Ensuretheoorislevelandstrongenough
tosupportafullyloadedwashingmachine.
6
edge of door
35mm
47mm
2mm
22.5mm
4.5mm
edge of door
45mm
2mm
31mm
468.5mm
597mm
716mm
384mm
84.5mm
*21.5mm
12mm
(+1mm)
35mm Dia.
Example
B(3x15mm)
Cross head
B(3x15mm)
TOP
TOP
Left hand hinged door
openingshown,
(righthandopposite).
*Check and drill
hole according to
the actual hole
drilling position of
door frontal range
being used.
www.howdens.com
5 - Prepare the décor door
Ifrequired,thandlesatthisstage,
(screwsmayneedcountersinking).
7
REMOVE
CAP/END
max.
100mm
min
500mm
min
300mm
max
1000mm
min
500mm
min
300mm
max
1000mm
www.howdens.com
Alldimensionsaretotheoor. DO NOT insertthehosetoodeepintothewastepipe,
(Maximum hose length, 3.2 metres).
6 - Washing machine connections
WARNING!Thisappliance
mustbeearthed.
(Socket must be accessible
after tting).
Ensurecap/endisremovedfrom
wastepipespigot.
WARNING!Donotuseextension
cables/adapters.
Ensure water is turned on and
the isolator valve is accessible
after tting.
Hoseconnection-3/4”.
Coldwaterpressure-
0.1–1Mpa(0.3-1.0Bar)
NOTE: Ensure hoses are not
kinked or trapped behind the
washing machine.
NOTE: Ifnecessaryloosenand
rotate the water hose towards
thewatersupplyandre-tighten.
(Always use the new hose
supplied with the washing
machine).
Cold water supply
10-80 lpm.
8
www.howdens.com
7 - Connect water hose (cold water supply only)
NOTE: Rotate the water hose
towardsthewatersupplyand
tighten.(Always use the
new hose supplied with the
washing machine).
Incorrectwastepipeconguration. Correctwastepipeconguration.
9
&
www.howdens.com
8 - Positioning the washing machine
NOTE: Ensure hoses
are not kinked or
trapped behind the
washing machine.
DO NOT PUSH against the washing machine fascia panel.
DO NOT adjust the rear feet
until in nal position,
(NEVER move the washing
machine with the rear feet
extended).
10
A(4.5x10)
A(4.5x10)
x2
www.howdens.com
9 - Fit décor door and magnetic catches
11
DO NOT use high
speedimpact
powertools.
DO NOT damage
theplasticscrew
heads.
Loosen the locknut(s) and
adjustthefrontfeet.
Adjustfrontfeetbyhand.
Tightenlocknut(s)byhandonly.
Rear
foot
Rear
foot
www.howdens.com
10 - Raise and level the machine
Raise and level the washing
machine using the front and
rearfeet.
Adjustrearfeetbyusingfrontscrews.
NOTE: Therearfeetscrewadjustmentishanded.
Final check for level,
remove the detergent
drawer and view the
spiritlevel.
MAKING SPACE MORE VALUABLE
ProductinformationcorrectatthetimeofpublicationinJune2018.Thecompanyhasapolicyof
continuousproductdevelopmentandreservestherighttochangeanyproductsandspecications
giveninthismanual.SubjecttotheTermsandConditionsofTrading,acopyoftheHowdensJoinery
TermsandConditionsisavailableuponrequest.
HowdenJoineryLtd,FirstFloor,40PortmanSquare,London,W1H6LT.
RegisteredinEngland526923
816010AA
12 - Plinth
Ensurecustomercanremoveplinthsectioneasily.
Accesstolteranddrainhoseisnecessaryafterinstallation.
Ensure hose remains in position during installation.
DO NOT remove end cap.
11 - Drain hose and lter
Werecommendthelengthofplinth
in front of the washing machine is
easilyremovableforeasyaccessto
drainhoseandlter.
/