ALIBI ALI-CD700WAIR Installation and User Manual

ALIBI
Brand
ALIBI
Model
ALI-CD700WAIR
Category
Security cameras
Type
Installation and User Manual
1
www.observint.com
ALI-CD700WAIR_CQ
10/21/14
Power
Connector
Audio BNC
Connector
Video BNC
Connector
Camera drop cable connectors
What’s in the box
• Camera assembly
• Drill template
• Video test cable
• Adjuster (for camera module)
• Security L- wrench
• Mounting hardware (screws and wall inserts)
• Pad
• This manual
Security L-wrench
Adjuster
Mounting
hardware
Pad
Video test cable
Tools you need
To install the camera, you will need:
• 12 Vdc power source. See Specications for voltage and wattage requirements.
• Tools and additional fasteners (may be required) for mounting the camera
• Video, audio and power extension cables
• CCTV video setup monitor (optional)
Installation
Before installation:
• Make sure that the device is in good condition and all the assembly parts are included.
• Check the specication of the products for the installation environment.
• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specications section.
During installation:
• Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning section.
• Monitor impedance: Set the monitor impedance switch to 75 Ω.
• Power supply: Camera drop cable: The camera drop cable includes two connectors:
— Video BNC connector: For transmission of the video signal across a coax (75 Ω) BNC extension
cable.
— Power connector: When applying Vdc power, observe the power polarity. See the picture
above for connector polarity conguration.
— Audio BNC connector: Connect the audio drop cable to a coax (75 Ω) BNC extension cable.
1. Using the drill template provided with your camera, mark the location of the two screws that anchor
the base assembly to the mounting surface. If you are routing the drop cable through base, also
mark the position of the hole for the drop cable. (See the template above.)
ALI-CD700WAIR Infrared Mini Dome
Camera Installation and User Guide
The ALIBI ALI-CD700WAIR dome camera include a new generation sensor with high sensitivity and
advanced circuit design technology. It features high resolution, low image distortion and low noise features
which makes them suitable for surveillance and image processing systems.
Features
• High resolution color sensor: 700 TV Lines
• IR cut lter enables the day/night surveillance
• Auto white balance with high color rendition
• Auto electronic shutter control adapts to dierent surveillance environments
• Auto gain control, adaptive brightness
• Internal 3-axis adjustment
• Weather protection: IP66 rated
1.83"
3.92"
ALI-CD700WAIR camera assembly front and side views
3.82"
Drop cable
Microphone
Base
assembly
IR array
Lens
Camera
module
Pan
adjust.
lock screw
OSD
joystick
Hole for
mounting
screw
Hole for
mounting
screw
Jack for
video test
cable
Hole for
cover
screw (4)
ALI-CD700WAIR camera internal components
2 www.observint.com
2. Drill holes for the screws that anchor the base to the ceiling. The mounting hardware provided is
appropriate for most surfaces. However, depending on the surface materials, more appropriate
fasteners may be required.
3. If using wall inserts for the mounting screws, install them at this time.
4. Drill a 3/4” hole for the camera drop cable, if necessary. The drop cable can be routed through the
mounting surface, or through a cable channel in the base assembly.
5. Route video, power and audio extension cables from your power and monitoring equipment to the
mounting location of the camera. Do not apply power to the power extension cable at this time.
6. Using the L-wrench provided, loosen the four cover screws, and then lift the cover o of the base
assembly.
Cover (captive)
screw (4)
7. Connect the camera drop cable to the video, power and audio extension cables.
8. Place the pad on the mounting location, and then anchor the base assembly to the surface over the
pad.
9. Connect the video, audio and power extension cables to your monitoring and power equipment.
Apply power to the camera.
10. If you have a CCTV video setup monitor, attach the video lead to the video test cable provided, then
plug the video test cable into the video test jack (see photos above).
11. Verify that you can see a clear video image from the camera on your monitoring equipment, and the
audio is clear.
12. Loosen the pan adjustment screw slightly so that the camera module pan (left and right) can be
adjusted.
13. Attach the “adjustor” tool provided to the camera module. See below.
Adjustor tool
Pan lock screw
14. While holding the adjustor in place and observing the video from your camera, adjust the pan, tilt
and rotation of the camera module to aim it at your surveillance target.
CAUTION: Avoid touching the camera lens.
15. Remove the adjustor tool.
16. Tighten the pan lock screw.
17. Use the OSD menu system to customize the settings for your camera. See OSD Menu System
below.
18. Reinstall the camera cover.
OSD Menu System
1. Locate the OSD joystick on base assembly.
Joystick
Reset button
The OSD joystick is used to open the OSD menu and navigate through the menus. To open the
camera menus and select a menu option, press the joystick down (in toward the base assembly).
To navigate the menus, rock the joystick up (
p, U) or down (q, D) to move through the parameter
list menus vertically, rock the joystick left (
t, L) or right (u, R) to change the parameter value
that appears for the parameter. Press the joystick down (in toward the base assembly) to select the
parameter value shown. Changes made to the OSD setup must be saved to be retained. See NOTES
below.
2. Open the OSD menus by pressing the joystick in toward the base assembly. The OSD menu tree is
shown below.
SETUP
NRBrightness
MirrorContrast
LanguageColor Gain
System SetupSharpness
Motion
Alarm
Function
Setup
Save & Exit
Reset
Lens Type
AGC
DWDR
Exposure
Mode
WB
Mode
D&N Video Setup
3. Navigate through the menu OSD menus as adjust the camera function as needed.
Notes on the OSD:
After making changes to the parameters in the OSD menu, they must be SAVED to retain them after closing
the menu. See the SAVE & EXIT submenu below.
• EXPOSURE submenu:
— Lens: Select FIX or IRIS
— AGC: Select HIGH, MIDDLE, LOW or OFF for the best performance.
— DWDR: Select HIGH, MIDDLE, LOW or OFF for the best dynamic range performance.
• WB (White Balance) submenu:
— Mode: Use AUTO 1 for environments where the color temperature is stable. Use AUTO 2 for
environments where the color temperature changes.
• DAY & NIGHT submenu:
— Mode: Select SMART, AUTIO, B/W, or COLOR. If SMART is selected, day and night mode switches
automatically.
— SET: Select ON (IR LED is on), or OFF.
© 2014 Observint Technologies. All rights reserved.
3
www.observint.com
© 2014 Observint Technologies. All rights reserved.
• VIDEO SETUP submenu:
— BRIGHTNESS: Rock the joystick left or right to adjust the brightness of the video image.
— CONTRAST: Rock the joystick left or right to adjust the contrast of the video image.
— COLORGAIN: Rock the joystick left or right to adjust the color gain of the video image.
— SHARPNESS: Rock the joystick left or right to adjust the sharpness of the video image
— NR: Rock the joystick left or right to set the noise reduction to HIGH, MIDDLE, DEFAULT, or LOW.
— MIRROR: Rock the joystick left or right to set the mirror eect (reection) to HV (horizontal and
vertical reection), H (horizontal reection), or V (vertical reection).
— LANGUAGE: Select ENGLISH or CHINESE.
• SYSTEM SETUP submenu:
— OSD COLOR: Rock the joystick left or right to select either RED, WHITE or YELLOW.
— OSD BG: Rock the joystick left or right to select either background ON or OFF.
• FUNCTION SETUP submenu:
— MOTION: Rock the joystick left or right to select the motion detection area (1 .. 5).
— ALARM: Rock the joystick left or right to select either alarm ON or OFF. When ON, the motion
detection area ickers when motion is sensed in that area.
• RESET submenu:
— RESET: Select RESET to set the camera to it’s factory default conguration.
• SAVE & EXIT submenu:
— SAVE & EXIT: Select SAVE & EXIT to save your settings and close the OSD menu system.
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
Troubleshooting
Problem Possible Cause
Nothing appears on the screen - Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark. - Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and the
surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor ickers - Make sure that the camera isn’t facing direct sunlight or uorescent light.
If necessary,change the camera position.
Specications
Parameter Specication
Image Sensor 1/3” DIS
Signal System NTSC
Eective Pixels 976 (H) × 496 (V)
Min. Illumination 0.1 Lux @ (F1.2, AGC ON), 0 Lux with IR
Shutter speed 1/60 s to 1/100,000 s
Lens 2.8 mm @ F2.2
Angle of view 68.4° (2.8 mm)
Lens Mount M12
Angle Adjustment Pan: 0 ~30°, Tilt: 0 ~ 80°, Rotation: 180°
Day & Night IR cut lter with auto switch
Horizontal Resolution 700 TVL
Synchronization Internal synchronization
S/N Ratio More than 62 dB
Menu
Auto Gain Low/Middle/High/O
D/N Mode Auto / Color / B/W / SMART
White Balance Auto 1/Auto 2
D-WDR Low/Middle/High/O
Motion Detection On/O, maximum 6 zones
Language English/Chinese
Function Brightness, Contrast, Saturation, Sharpness, NR, Mirror
Interface
Video Output 1 Vp-p composite output (75 Ω, BNC connector)
Audio In Built-in Microphone
Audio Output 1-ch audio interface (BNC connector)
General
Working Temperature -40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity 90% or less (non-condensing)
Power Supply 12 VDC
Power Consumption Max. 2W (Max. 4W with IR cut lter on)
Impact Protection IEC 60068-2-75 test, Eh, 50J; EN 50102, up to IK07
Ingress Protection IP66
IR Range Up to 65 ft approx.
Dimensions 3.82” × 1.83” × 3.92” (97 × 46.6 × 99.5 mm)
Weight 0.66 lb (300 g)
  • Page 1 1
  • Page 2 2
  • Page 3 3

ALIBI ALI-CD700WAIR Installation and User Manual

ALIBI
Brand
ALIBI
Model
ALI-CD700WAIR
Category
Security cameras
Type
Installation and User Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents