Extron ISM HDSDI User manual

Extron
Brand
Extron
Model
ISM HDSDI
Category
Video converters
Type
User manual
The Extron
®
ISM HDSDI is
a universal video and RGB
scaler board with HDSDI
output for the ISM 824.
It has a single BNC connector and a local audio
output. The board mounts in one of the four vertical expansion slots
(numbered 1 to 4) at the rear of the ISM 824. Refer to the ISM 824 User Guide,
available at www.extron.com.
To install an ISM HDSDI output board in the ISM 824 base unit:
1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.
2. Select an open slot at the rear, or take out a blank plate by removing the two
retaining screws (top and bottom), and lifting the plate away.
NOTE: Retain and reuse the screws to secure the new output board in place.
Retain the blank plates. If a board is already installed in the desired slot,
remove the screws and carefully pull out the board.
3. Holding the new board by the frame,
align the front (non-connector end) of the
board with the top and bottom plastic
guides in the ISM 824. Slide the board in
carefully, keeping within the guides. Push
it into place firmly, and secure it with the
retained screws.
4. If required, repeat steps 2 through 4
for any other output boards.
5. Power on the ISM 824. The new output
board(s) is autodetected, and takes
approximately 30 seconds to initialize.
The 16 character LCD display indicates the new board type,
slot used, and counts down the initialization time. See inset
for example display of a new ISM HDSDI board installed in
slot #2, with 16 seconds left.
6. Connect a suitable display device to the BNC connector. The output can be
configured via the front panel (see page 2) or by SIS
™
commands (see page 3).
7. Insert a 5-pole captive screw connector into the local audio output connector
for balanced or unbalanced stereo output. Wire the connector as shown below.
1
100
-
240
50/60 Hz
1.2A MAX.
1
2 3 4 5 6 7
8
2
1 2
3 4 5 6 7 8
1
2
1
INPUTS
OUTPUTS
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
R/R-Y
G/Y
VID
B/C
B-Y
H/HV
V
PASS THRU
INPUTS
RESET
LAN
REMOTE
RS232/RS422
ACT
LINK
OUTPUT
VIDEO
SCALER
70-545-01
3
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
UNIV.
SCALER
70-544-01
5
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
PASS
THRU
70-547-01
8
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
Extron
ISM 824
Integration Scaling
Matrix Switcher
Align output board
with top and bottom
plastic guides.
R/
R-Y
G/Y
B/
B-Y
H/
HV
V
OUTPUT
7
SCAN
CONV.
70-546-01
Example Output Board Installation
NOTE: X! = Input number, 0-8
X@
= Output number, 1-8
X1)
= Mode status, 1 = on, 0 = off
X2)
= Test pattern, 00 = off, 01 = color bars, 02 = 4:3/16:9 crosshatch, 03 = 4x4 crosshatch,
04 = split gray scale, 05 = ramp, 06 = alternating pixels, 07 = crop, 08 = 1.33 aspect,
09 = 1.78 aspect, 10 = 1.85 aspect, 11 = 2.35 aspect
X2!
= Output resolution, 17 = 720p, 18 = 1080i, 19 = 1080p
X2@
= Refresh rate, 1 = 50 Hz, 2 = 60 Hz, 7 = 24 Hz, 8 = 25 Hz, 9 = 30 Hz, 10 = 59.94 Hz
X5%
= Aspect ratio, 1 = 16:9, 0 = 4:3
ISM HDSDI Output Board • Setup Guide
New Univ HDSDI
Slot #2 16
ISM HDSDI
HDSDI
UNIVERSAL
SCALER
HDSDI
L
R
Unbalanced Stereo Output
Balanced Stereo Output
Tip
Ring
Sleeve(s)
Tip
Ring
L R
Left
Right
Tip
Sleeve(s)
Tip
L R
Left
Right
NO GROUND HERE.
NO GROUND HERE.
CAUTION: For unbalanced audio, DO NOT connect the sleeves to the
negative contacts. Connect to center ground contact.
ISM HDSDI Output Board • Setup Guide, cont’d
ISM HDSDI Configuration Menu
Using the front panel menu buttons (Menu and Next), the ISM HDSDI
configuration menu can be accessed. From the Output Configuration screen, press
Next until reaching the #x Univ HDSDI menu (see the image below). Press Menu
and Next to navigate through the menus and use the front panel Adjust knobs
({ [), to change the settings as desired. Refer to the ISM 824 User Guide, online
at www.extron.com for full details.
From the default cycle press Menu repeatedly to reach the Output
Configuration menu. Press Next (enters Select Output menu) and rotate
either Adjust knob to select the Univ HDSDI menu. Follow the figure
below to enter each menu and use the Adjust knobs to change the value.
Se le ct O ut put
#8 Un iv H DSDI
Next
In pu t Se tu p
#8 Un iv H DSDI
As pe ct R at io
4: 3
Next
Rotate either knob
to select Aspect Ratio
(4:3 or 16:9).
Next
H St ar t V
12 8 12 8
Rotate knob to
adjust H(orizontal) start.
Rotate knob to
adjust V(ertical) start.
Next
Total Pix Ph a s e
17 2 8 0 0
Rotate knob to
adjust Total Pix value.
Rotate knob to
adjust Phase value.
.
Next
H Ac t i v e V
12 8 3 1 0 2 8
Rotate knob to
adjust H active value.
Rotate knob to
adjust V active value.
Menu
Next
Ou t p u t C o n f i g
#8 U n i v H D S DI
Rotate knob to
adjust resolution.
Rotate knob to
adjust refresh rate.
Next
10 8 0 i 6 0 Hz
Re s o l u t i o n
Next
Menu
Us e r P r e s e t s
#8 U n i v H D S DI
30 sec.
<N A > 1 2 3
Save Preset
Next
Rotate either knob
to select a preset to
save current settings.
<N A > 1 2 3
Er a s e P r e s e t
Next
Rotate either knob
to select a preset
to erase.
Advanced C o n f i g
#8 U n i v H D S DI
Next
No n e
Te st Pa t t e r n
Rotate either knob
to select a test pattern.
<O f f > O n
Bl u e M o d e
Next
Rotate either knob
to turn blue mode On
or Off.
Next
Of f < O n >
Fi l m M o d e
Rotate either knob
to turn film mode On
or Off.
Next
Menu
Next
Next
Rotate knob to
select input.
Rotate knob to
turn On or Off.
In p u t # 2 O f f
Auto I m a g e
Auto Memory
Next
Rotate either knob
to turn auto memories
On or Off.
Of f < O n >
In p u t # 2 O f f
Fu l l S c r e e n
Rotate knob to
select input.
Rotate knob to
turn On or Off.
Next
NOTE: Within any submenu, press the Menu button
to go directly to the top level (Output Card
Configuration) menu. If, for 30 seconds, no
button is pressed or Adjust knob is rotated,
the menu times out and reverts to the default
display cycle.
Input Setup
The Input Setup submenu allows configuration of aspect ratio, horizontal and
vertical start points, total pixels and phase value, and active horizontal and vertical
areas. Rotate the Adjust knobs as required to change values.
MENU NEXT
ADJUST
2
Output Config
The Output Config submenu displays and allows changes to be made to the
resolution and refresh rate. Use the Adjust knobs to select a resolution and
refresh rate.
Resolution 24 Hz 25 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz
720p X X X X X X
1080i X X X
1080p X X X
User Presets
The User Presets submenu displays and allows the current settings to be saved
as a preset, or to erase an existing saved preset. Use the Adjust knobs to select
between the presets.
Advanced Config
Within this submenu the following settings can be adjusted:
auto image (on or off), test pattern (selection), blue mode (on or off),
auto memories (on or off), film mode (on or off), and full screen (on or off).
Test Pattern
The test pattern submenu offers the following test patterns to choose from:
Color Bars
Split Grayscale
4x4 Crosshatch
Alternating
Pixels
4:3/16:9
Crosshatch
1.78 Aspect
1.85 Aspect 2.35 Aspect
1.33 Aspect
Crop
Ramp
3
NOTE: X! = input number, 0-8
X@
= output number, 1-8
SIS commands and definitions continue on page 4.
Board-specific SIS Commands
The ISM HDSDI board can be configured with specific Simple Instruction Set
™
(SIS)
commands. The table below and on page 4 lists some of the ISM HDSDI board
specific commands. Refer to the ISM 824 User Guide, at www.extron.com for a list.
Command ASCII
Command
(host to ISM)
Response
(ISM to host)
Additional Description
Input selection
Video and audio X!*X@!
OutX@•InX!•All
]
Tie video/audio input X! to X@.
Video X!*X@&
OutX@•InX!•RGB
]
Select video input X! to X@.
Audio X!*X@$
OutX@•InX!•Aud
]
Select audio input X! to X@.
Extron USA - West
Headquarters
+800.63 3.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
+800.63 3.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron Europe
+800.39 87.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
Inside Asia Only
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FA X
Extron Middle East
+971.4.2991800
+971.4.2991880 FAX
68-1123-65
Rev A
08 10
© 2010 Extron Electronics. All rights reserved. www.extron.com
4
Command ASCII
Command
(host to ISM)
Response
(ISM to host)
Additional Description
Output scaler rate
Set output rate
X@
*
X2!
*
X2@
=
RteX@ *X2!*X2@
]
Set resolution/refresh rate.
View
X@
= X2!*X2@
]
View selected output rate.
Start auto image
Start auto image 14*X@# ImgX@
]
Auto image input tied to X@.
Auto memory
On X@
*1M
X@
Aut1
]
Set auto memory to on.
Off
X@
*0M
X@
Aut0
]
Set auto memory to off.
View setting
X@
M
X1)]
View current auto memory.
Auto image
Enable
55*X@* X!*1#
X@ImgX!*1
]
Enables auto image for all
inputs.
Disable 55*X@* X!*0# X@ImgX!*0
]
Disables auto image.
View
55*X@* X!#
X1)
]
View auto image setting.
Input aspect ratio
16:9 9*X@*1# X@AspX!*1
]
Set input aspect ratio to 16:9
.
4:3 9*X@*0# X@AspX!*0
]
Set input aspect ratio to 4:3
.
View 9*X@#
X5%
]
View current aspect ratio.
Full screen
Enable 99*X@*X!*1# X@FulX!*1
]
Enables full screen view.
Disable 99*X@*X!*0# X@FulX!*0
]
Disables full screen view.
View 99*X@*X!#
X1)
]
View the current on/off status.
Test pattern
On X@*X2) J X@TstX2)
]
Select test pattern.
View X@ J
X2)
]
View the test pattern selected.
NOTE: X! = Input number, 0-8
X@
= Output number, 1-8
X1)
= Mode status, 1 = on, 0 = off
X2)
= Test pattern, 00 = off, 01 = color bars, 02 = 4:3/16:9 crosshatch, 03 = 4x4 crosshatch,
04 = split gray scale, 05 = ramp, 06 = alternating pixels, 07 = crop, 08 = 1.33 aspect,
09 = 1.78 aspect, 10 = 1.85 aspect, 11 = 2.35 aspect
X2!
= Output resolution, 17 = 720p, 18 = 1080i, 19 = 1080p
X2@
= Refresh rate, 1 = 50 Hz, 2 = 60 Hz, 7 = 24 Hz, 8 = 25 Hz, 9 = 30 Hz, 10 = 59.94 Hz
X5%
= Aspect ratio, 1 = 16:9, 0 = 4:3
ISM HDSDI Output Board • Setup Guide, cont’d
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron ISM HDSDI User manual

Extron
Brand
Extron
Model
ISM HDSDI
Category
Video converters
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents