Wyrestorm SW-1001-HDBT Quick start guide

Brand: Wyrestorm

Model: SW-1001-HDBT

Type: Quick start guide

Quickstart Guide

WyreStorm 10 x 1 HDBaset Presentation Switcher

with Mic Control and CEC

SW-1001-HDBT

Attention: Open out for installation diagram.

Before Installation

• Check compatibility of source/display devices and device

settings prior to connection and operation

• Make sure of firm cable connection to devices but do not force

connectors into ports

• Always use good quality, high speed Category 2 HDMI cables

within the transmission distance specification for devices used

– we recommend WyreStorm Express HDMI cables

• Although WyreStorm products are tested with Cat5e, we

recommend Cat6 as standard due to increased bandwidth and

improved capacity for handling large transmissions and power

along a single cable.

• This unit will auto-scale output according to EDID settings of

connected sync device. See full manual for details on how to

manually override this function.

Set-up

At source location, connect VGA (with corresponding audio input)

HDMI, HDBaseT and DisplayPort devices as required, either directly

to the rear of the SW-1001-HDBT or via a desk plate, ensuring firm

port connection using good quality cables.

NOTE: VGA audio inputs are embedded and passed with

transmissions.

If using an external microphone, connect to MIC input 1 or 2 and

adjust the input level (MIC GAIN) on the front of the unit – microphone

inputs are embedded independently over the selected video source.

Ensure the Phantom Power setting is turned ON if using a

microphone requiring 48V power and OFF If using a dynamic

microphone.

A source in a remote location up to 100m/328ft* from the SW-

1001-HDBT can be distributed and powered using HDBaseT and

POH technology in conjunction with a compatible WyreStorm PoH

transmission device to eliminate the need for mains power supply

at the remote source location. (See full manual for compatible

transmission devices)

*Depending on HDBaseT classification used in the transmission

device - Class A (100m) / Class B (70m)

Connect good quality, well-terminated Cat6 cable between the HDBT

or UTP OUT port of the transmission device and the HDBT IN port

of the SW-1001-HDBT and connect IR/RS232 to a control system if

used.

NOTE: Control of display device (projector/screen) from the

remote location is achieved by sending embedded commands

from the HDBaseT transmitter through SW-1001-HDBT and

passed along the HDBaseT link to the receiver at the display

location.

Output connection is via mirrored HDBaseT and HDMI, with HDMI

connection to a local display device up to 15m using High Speed

Category 2 HDMI cables from a quality brand such as WyreStorm

Express.

For HDBaseT output, connect another well terminated Cat6 cable of

no more than 100m/328ft from the HDBT OUT of SW-1001-HDBT

to the HDBT IN of a compatible PoH-enabled WyreStorm receiving

device at display location (See wyrestorm.com for compatible

receiving devices.)

A PoH-enabled receiver or compatible display device can be

remotely powered by the SW-1001-HDBT so no power outlet is

required at the receiver location.

NOTE: Optional power connectivity is available on both

transmission and receiving devices if required, for example if a

cable is too weak to carry power.

Any HDBaseT transmitter or receiver can be used but support of

features (such as PoH, serial control, Ethernet etc.) is dependent

on model. Check the specification of the TX or RX device before

installation.

Connect to a control system via RS232 or LAN as required, ensuring

RS232 connections are in place at source and display locations.

Connect a network cable from a router or Ethernet switch to the

LAN 1 port to add Ethernet to the HDBaseT transmission. Connect a

cable also to LAN 2 if controlling via a LAN enabled control system.

Audio breakout is offered as a fixed line-out or variable pre-out for

connection to power amplifiers with no in-built volume control.

Control of this function is via Web UI or command protocol for the

switch. See full manual for details

To reset IP address or auto-scaling functionality for any reason, press

to reset to default settings.

NOTE: This action cannot be undone so would require set up

to be repeated.

Connect power cable included and switch on the power at the rear of

the unit – a lit red power LED on the front panel will indicate the unit

is powered.

Wiring and Connections

HDBaseT Wiring

Wiring for HDBaseT follows the EIA T568B standard.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference can have an adverse effect on

HDBaseT transmission limiting performance. Steps should be taken to minimize these factors (or remove completely) during installation for best

results.

Specications

Pin 1

Pin 8

RJ-45 Connector (Gold Pins Facing Up)

Pin 2:

Orange

GreenPin 6:

Pin 1: White/Orange

Pin 5: White/Blue

Pin 3: White/Green Pin 7: White/Brown

Pin 4: Blue

Pin 8: Brown

Pin 2:

RX (Receive)

Pin 1: TX (Transmit)

Pin 3: Ground (GND)

Wire colors shown follow EIA-561 standard.

1 2 3

RS232 Wiring

Audio and Video

Audio Connection 3-pin phoenix port (MIC), 3-pin phoenix

port (Stereo)

Audio Formats Stereo

Video Connection HDMI 1.3a (input/output), HDBaseT

(output)

Video Resolution HDMI: Up to 1920x1200p @ 60Hz

VGA: Up to 1920x1200 @ 60Hz

Color Depth 36bit

Control

Method Bi-directional IR, bi-directional RS-232,

front panel buttons, I/O control devices,

LAN (Telnet & Web GUI)

Ports IR, RS232-1, RS232-2, CONTACT IN,

LED OUT, LAN

Power

Input Power 100-240VAC 50/60Hz

Max Power Consumption 26.5W

HDBaseT (PoH) 15.4W (HDBT OUT)

Phantom Power (for MIC) 48 VDC 100 mA

Dimensions and Weight

Height 50mm/1.9”

Width 440mm/17.3”

Depth 280mm/11.0”

Weight 4.0kg/8.81lbs

Environmental

Operating Temperature 32°F ~ 113°F (0°C ~ 45°C) 10% ~ 90%,

non-condensing

Storage Temperature -4°F ~ 140°F (-20°C ~ 70°C) 10% ~

90%, non-condensing

ESD Protection ±8kV (Air-gap discharge), ±4kV (Contact

discharge)

Surge Protection Voltage: ±1 kV

REGULATORY

Safety and Emission CE | FCC

RoHS Compliant

Cable Performance Guide

SW-1001-HDBT

0ft 328ft32ft 65ft 98ft 131ft 164ft 197ft 230ft 262ft 295ft

0m 100m10m 20m 30m 40m 50m 60m 70m 80m 90m

HDMI* Transmission HDBaseT Class B Cat5e/6 Transmission

HDBaseT Class A Cat5e/6 Transmission

Operation

The SW-1001-HDBT features hot-plug detection to enable instant

switching to any source device plugged in to the rear of the unit or a

desk plate, and instant disconnection from any device unplugged. On

removing a connected device, the SW-1001-HDBT will return to the

last available active source connected.

The unit also includes CEC support to trigger an ‘ON’ command for

the sync device when connecting an active source. Disconnecting

or powering off sources instructs the sync device to turn off after a

predefined period of time – duration variable between 1min-1hour or

function can be deactivated.

(See full manual for further CEC details and customization.)

Control the SW-1001-HDBT via local push button, Web UI or RS232

using control protocols, with local source selection made by pressing

the relevant button on the front panel.

A static green LED above the input button indicates the source

selected and flashing blue STATUS LED illustrates the SW-1001-

HDBT is active and functioning correctly.

See full manual for operation using Web UI and RS232.

Troubleshooting

Regardless of manufacturer or product, the majority of installation

diculties can typically be attributed to communication problems between

devices or when high bandwidth transmissions are attempted with

insucient cable/connections. Should you nd yourself in such a situation,

refer to the following checklist of common issues and causes that should

help you shoot your way out of trouble without seeking further assistance.

No or poor quality picture

Connected and powered? Double-check all device cables and power

connections are rmly inserted into correct ports and that all devices are

powered.

Are connected sources o or outputting an unsupported resolution?

Is the scaler set to an unsupported resolution for the display device?

Check an active connected source is selected.

Check HDBaseT transmission and receiving devices are operating

normally.

Test the system - conrm local HDMI outputs are functioning correctly

using pattern timing generator and signal analyzer test equipment - we

recommend the WyreStorm TT-KIT-4K Test Kit.

Use the test equipment to send a test signal into the SW-1001-HDBT

to check for correct signal routing prior to installation.

HDMI – make sure output resolution is not higher than the supported

1200p.

LED Indication. Check red POWER LED is lit to signify unit is

powered. Check blue STATUS LED on unit is ashing to indicate correct

functionality. Check green Input LED is lit to illustrate source is selected.

No or poor quality audio

VGA Audio – if VGA audio is not embedding, check cable and ensure

devices are outputting audio.

HDMI/DisplayPort Audio – check output audio signal is supported.

If no output audio, check the level is not set to zero in Web UI or serial

protocol

Receiving device – please be advised that the use of third party

HDBaseT receiving devices is not recommended. WyreStorm PoH-

enabled receivers are preferred method of receiving transmissions but

the WyreStorm AMP-001-010 digital audio amplier can also be used for

enhanced audio connectivity at display zones.

Note: AMP-001-010 is PoH compatible as a pass-through device

only. The unit itself will require local mains power.

Cable and signal

Cable length – is the signal struggling to transmit the distance of the

HDMI or Cat5e/6 cable? Interference may be exceeding the maximum

capacity of the transmission cable distance.

Try a shorter cable run or swap out cable or device for one you know is

functioning normally to rule out faulty equipment and cable.

Signal strength – the use of cable joins, stranded patch panels, wall

outlets and stranded patch leads as interconnects between them, can

signicantly reduce signal strength. Use solid core straight, straight

through connections wherever possible.

Resolution - If no signal, reduce the resolution of the output to 720p

or 576p. If a signal appears, a bandwidth issue with the cable is the likely

cause. Check all inputs and outputs share the same resolution and make

sure the signal is being successfully transmitted the full length of the cable

run.

Picture ‘snow’/HD ‘noise’ – signies a failure to fully establish a signal

and can often be caused by poorly terminated RJ45 connectors or

excessive cable lengths on distribution devices. Ensure any category

cable used is correctly wired to 568B standards. Try swapping in sources,

displays or transmission devices known to be functioning correctly – if the

problem continues on the same output, turn o all equipment and swap

the signal carrying cables at both ends.

Cable quality and condition – HDMI cable/connectors can be easily

damaged and the quality of material can vary, especially in the lowest

price brackets. Successful transmission of video, audio and control, can

all be aected by cable and termination quality. Always use good quality

leads and cables, with RJ45 connectors wired to the 568B standard at

both ends for category cables. We recommend using WyreStorm Express

high-speed HDMI cables.

In terms of HDBaseT transmissions, Cat6 is recommended as standard

due to increased bandwidth and improved capacity for handling large

transmissions and power along a single cable.

Should transmission problems be experienced, try swapping cables/leads

for those already working to see if this improves your image to identify

cable issue as source of problem.

Blu-ray - Make sure all your equipment has been congured and

enabled to transmit and accept the signal, or is capable of passing a

signal. Are resolutions between source and display compatible and cable

adequate for the large bandwidth required by Blu-ray transmissions?

4K – is 4K equipment being used within the installation? The SW-

1001-HDBT is not 4K compatible.

Safety Recommendations:

Do not expose this apparatus to any form of moisture, including the

placement of anything containing liquids on the unit.

To prevent risk of electric shock or re hazard, ensure apparatus is

installed in an unobstructed, well ventilated area away from any external

heat sources - including other electrical devices which may produce heat.

Only use attachments / accessories specied by the manufacturer and

refer all servicing to qualied service personnel.

Failure to adhere to these recommendations may invalidate your

warranty.

Warranty Information

This product is covered by a 3 year

limited parts and labor warranty. During

this period there will be no charge for

unit repair, component replacement or

complete product replacement in the event

of malfunction. The decision to repair or

replace will be made by the manufacturer.

This limited warranty only covers defects in materials or workmanship and

excludes normal wear and tear or cosmetic damage.

Visit our website for full details on this product and to download the

full instruction manual for complete information on this product and full

warranty terms and conditions.

wyrestorm.com

150807

For additional product information visit wyrestorm.com

For technical support contact:

North America: +1 844-280-WYRE (9973) EMEA/ROW: +44 (0) 1793 230 343

KEY

HDMI/DisplayPort

HDBaseT/Ethernet

Power

Analog Audio

IR/RS232

Speaker Level Audio

Analog Video

In the Box

1 x SW-1001-HDBT 10x1 HDBaset Presentation Switcher with Mic

Control and CEC

1 x Mains cable (UK/US/EU)

2 x Phoenix Connector (Male, 3.5 mm, 4 pins)

4 x Phoenix Connector (Male, 3.5 mm, 3 pins)

5 x Phoenix Connector (Male, 3.5 mm, 5 pins)

2 x Mounting brackets

1 x Quickstart guide (Quickstart and full manual also available to download

from product page on wyrestorm.com)

Podium PC with Microphone

IR RS232

Ethernet

Ethernet Ethernet

Analogue Audio

Analogue

Audio

HDMI Video /

Audio

HDMI Video /

Audio

HDMI Video /

Audio

HDMI SourceHDMI Source

Analog

Video

Analog

Audio

Digital

Video

VGA Video

WyreStorm HDBaseT

PoH Receiving device

Projector

Display

RS232

HDBaseT

Cat6 100m/328ft

HDMI Video /

Audio

Ethernet

HDMI Video /

Audio

Optional

Power

Local Amplier

Speaker Level Audio

Analog Audio

VGA Source

Transmission Device

Control

system

Media PC

Wyrestorm SW-1001-HDBT Quick start guide

Wyrestorm SW-1001-HDBT Quick start guide

Wyrestorm SW-1001-HDBT Quick start guide

Related papers

Other documents