eevi Life Pendant (EV04)
Exported on
19 January 2022
eevi Life Pendant (EV04)
19 January 2022
–
Table of Contents
1 EV-04 - Programming and Modification Instructions .............................................4
1.1 GPS Tracker Parameter Editor NEW DEVICE SETUP [for Tunstall Monitoring with Telstra Nano
SIM] .................................................................................................................................................4
1.2 EV-04 SMS / Text Commands Editing an ACTIVE Tunstall Monitored Device..............................9
1.3 EV-04 SMS / Text Commands Remotely Provisioning a NEW Tunstall Monitored Device........10
1.4 EV-04 SMS / Text Commands Remotely Provisioning a NEW Self Monitored Device ...............10
2 Eevi Life Pendant (White) - Post-shipping/Setup Instructions ............................11
eevi Life Pendant (EV04)
19 January 2022
– 3
•
•
•
•
•
The eevi Life Pendant (EV04) is available for professional monitoring.
In the Box:
charging doc
lanyard
charging cable
pendant
Telstra sim
eevi Life Pendant (EV04)
19 January 2022
EV-04 - Programming and Modification Instructions– 4
•
•
•
•
•
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
1 EV-04 - Programming and Modification Instructions
This document outlines configuration settings for the EV-04 (GEM 4) pendant to function with Tunstall, as
well as modifying settings in the field through SMS.
These settings can be applied to the pendant via SMS commands, the Eview configuration software and via
config.bin file generated by Tunstall and applied through the Eview configuration tool [GPS Tracker Parameter
Editor] Note: it is also possible to build our own config files.
Tools needed
Internet
cable
base station
computer
access to GPS Tracker Parameter Editor
1.1 GPS Tracker Parameter Editor NEW DEVICE SETUP [for Tunstall
Monitoring with Telstra Nano SIM]
Connect base station via the usb cable to the PC
Open the GPS Tracker Parameter Editor (see attached zip file to download program)
select ‘model’
from the drop down select ‘model 04’
select ‘open EVD’
select profile
select ‘.bin file’ (see attached)
go to system info
update the password (to the full PERS ID) for this pendant
update the prefix to ‘SAC-XXXX’
then save all.
open EVD to disconnect pendant from PC.
At this point a brand new pendant has been configured with a Telstra SIM and TUNSTALL response.
eevi Life Pendant (EV04)
19 January 2022
EV-04 - Programming and Modification Instructions– 5
NOTE: out of box testing was conducted with Vodafone and could not be made to work. At this stage the only
network that this device is compatible with is Telstra.
eevi Life Pendant (EV04)
19 January 2022
EV-04 - Programming and Modification Instructions– 6
eevi Life Pendant (EV04)
19 January 2022
EV-04 - Programming and Modification Instructions– 7
eevi Life Pendant (EV04)
19 January 2022
EV-04 - Programming and Modification Instructions– 8
eevi Life Pendant (EV04)
19 January 2022
EV-04 - Programming and Modification Instructions– 9
•
•
•
•
Parameter Editor Program:
ParamEdit-NoJDK-0.5.10.zip
Sample Config Files - PERS ID will require updating:
*note that it is important any spacing within the .bin files remains the same. It is key to Tunstall receiving all of the
required information from the pendant
640002.bin640001.bin
1.2 EV-04 SMS / Text Commands Editing an ACTIVE Tunstall Monitored
Device
This tool is used for a device that is already programmed. These SMS functions allow remote changes once the
device has been fully programmed.
Tools needed:
Internet
Jasper Access
Sim Card number
Device powered up and on
eevi Life Pendant (EV04)
19 January 2022
EV-04 - Programming and Modification Instructions– 10
•
•
•
•
•
•
•
•
•
•
•
PERS ID
1.3 EV-04 SMS / Text Commands Remotely Provisioning a NEW Tunstall
Monitored Device
This tool is used for a device that is already programmed. These SMS functions allow remote changes once the
device has been fully programmed.
Tools needed:
Internet
Jasper Access
Sim Card number
Device powered up and on
PERS ID
1.4 EV-04 SMS / Text Commands Remotely Provisioning a NEW Self
Monitored Device
This tool is used for a device that is already programmed. These SMS functions allow remote changes once the
device has been fully programmed.
Tools needed:
Internet
Jasper Access
Sim Card number
Device powered up and on
PERS ID
eevi Life Pendant (EV04)
19 January 2022
Eevi Life Pendant (White) - Post-shipping/Setup Instructions– 11
•
•
•
•
•
2 Eevi Life Pendant (White) - Post-shipping/Setup Instructions
Our Eevi Life Pendant (White) aka EV-04/GEM4 gets shipped with a booklet which contains an insert instructing the
client to call us when the device arrives. This doc contains some information to provide the client with, setup
instructions and a walkthrough of a test call to Tunstall (the monitoring centre for these devices).
This is the insert sent out with the Eevi Life Pendant:
Once it arrives with the client, we should expect a call. The purpose of that call is to familiarise the client with the
pendant (how to raise an alarm, how to charge it, a quick explanation that GPS will work best outside, explain that
invoices will begin after the first 3 free months). To initiate the test call to Tunstall, the SOS button is held for 2
seconds, it will then vibrate and the button can be released. The call sequence will begin.
The following are some points you might like to discuss with the client:
The GPS on the device works best outside. The response centre will have difficulty accurately locating you
inside, particularly in a multi-level building like a shopping centre
The Eevi Life Pendant is charged by placing it in the charging dock. We suggest that you do this every night
to ensure a full day of charge.
When unboxing the pendant, there is a few things you will find.
There is a lanyard to attach, if you wish to wear the pendant around your neck
There is the charging base unit, a cable and a charging brick - attach the smaller end of the cable into
the charging base unit and the larger USB side into the charging brick. The charging brick can than be
plugged into a power point
/
