Shine Company 4698BB Operating instructions

Shine Company
Brand
Shine Company
Model
4698BB
Category
Computer cases
Type
Operating instructions

This manual is also suitable for

Step 1:
Place Seat on its side and
screw Front Leg with three
Short Machine Thread (6 x 50 m/m)
and three Nuts. Repeat on the
other side.
A
B
How To Assemble Your Porch Rocker
TOOLS NEEDED: Philips screwdriver, power drill optional
CAUTION: When assembling chair, DO NOT completely tighten the bolts and nuts until all the parts & holes
are properly aligned.
8 PC Wood Screws (3.5 x 40 m/m)
16 PC
Nuts
4 PC Lag Bolts (6 x 60 m/m)
14 PC Short Machine Thread (6 x 50 m/m)
2 PC Long Machine Thread (6 x 70 m/m)
2 PC Short
Machine Thread
(6 x 50 m/m) & 2 Nut
2 PC Short Machine
Thread (6 x 50 m/m)
& 2 Nut
PARTS INCLUDED: HARDWARE INCLUDED:
4 PC
Barrels
E
Back Rest
G
Wood Slat
F
Rocker Slats
Arm Rest
D
Rear Armrest
Support
C
Front Leg
B
Seat
A
Step 2:
Place Seat in upright position.
Screw Rear Armrest Support
with two Short Machine Thread
(6 x 50 m/m) and two Nuts to Seat
so that it is perpendicular to the floor.
Repeat on the other side.
NOTE: Lightly screw the bolts of
Rear Armrest Support to properly
attach to Armrest in the next step.
A
C
A
C
D
3 PC Short Machine
Thread (6 x 50 m/m)
& 3 Nuts
(REV. 03/2017)
3 PC Short Machine
Thread (6 x 50 m/m)
& 3 Nuts
R
R
L
L
D
D
C
Step 3:
Attach the back of Armrest to Rear
Armrest Support with one Long Machine
Thread (6 x 70 m/m) and one Nut. Repeat on
the other side. Leave Armrest sitting on
Front Legs for now and do not attach
the screws.
B
B
B
B
B
A
G
D
A
A
E
E
E
E
Step 4:
Place two barrels into the holes found on the
inner sides of Seat and place two barrels
into holes found at the inner side of Rear
Armrest Support.
Remove any debris from holes in Back
Rest. Fit Back Rest onto Rear
Armrest Support.
Once fitted, use two Lag Bolts (6 x 60 m/m)
to attach Back Rest to Seat and the
remaining two Lag Bolts (6 x 60 m/m) to
attach Back Rest to Rear Armrest
Support.
Step 5:
Use 1 Short Machine Thread (6 x 50 m/m) &
1 Nut to attach Rocker Slats to Rear
Armrest Support and 1 Short Machine Thread
(6 x 50 m/m) & 1 Nut to attach Rocker
Slats to Front Leg. Repeat on the other side.
Step 6:
Push Armrest forward until it hits the
wings of Front Leg and use 2 Wood
Screws (3.5 x 40 m/m) to attach them together
for both sides.
Step 7:
Take Wood Slat and place it on Front
Legs below Seat. Use 2 Wood Screws
(3.5 x 40 m/m) for each side to attach to
Front Legs.
C
C
C
C
F
F
A
A
B
B
G
C
D
D
E
E
A
A
B
B
C
D
D
F
F
1PC Long Machine
Thread (6 x 70 m/m)
& 1 Nut
1PC Long Machine
Thread (6 x 70 m/m)
& 1 Nut
1PC Short Machine
Thread (6 x 50 m/m)
& 1 Nut
1PC Short Machine
Thread (6 x 50 m/m)
& 1 Nut
1PC Short Machine
Thread (6 x 50 m/m)
& 1 Nut
1PC Short Machine
Thread (6 x 50 m/m)
& 1 Nut
2PC Wood Screw
(3.5 x 40 m/m)
2PC Wood Screw
(3.5 x 40 m/m)
2PC Wood Screw
(3.5 x 40 m/m)
2PC Wood Screw
(3.5 x 40 m/m)
Left
Right
1PC Lag Bolt
(6 x 60 m/m)
1 PC Barrel
(Inner Side)
1PC Lag Bolt
(6 x 60 m/m)
1 PC Barrel
(Inner Side)
1PC Lag Bolt
(6 x 60 m/m)
1 PC Barrel
(Inner Side)
1PC Lag Bolt
(6 x 60 m/m)
1 PC Barrel
(Inner Side)
  • Page 1 1
  • Page 2 2

Shine Company 4698BB Operating instructions

Shine Company
Brand
Shine Company
Model
4698BB
Category
Computer cases
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents