88LBS
40KG
Max:
Max:400x400mm/16x16"
Min:75x75mm /3x3"
26"~55"
(A0)
If you have any questions, please contact us via
help@jollyholding.com
MU0010 INSTALLATION INSTRUCTION
Velcro cable ties X5 Bubble level X1 HDMI cable X1
- 1 -
Hammer
3/8"(10mm)
Masonry Drill Bit
7/32"(5.5mm)
Wood Drill Bit
AwlStud Finder
Socket Wrench
1/2"(13mm)
ElectrodrillScrewdriverPencil
3
What is your wall
made of?
Solid concrete
wall?
● This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
● The wall must be capable of supporting five times the weight of the TV and mount
combined.
● Do not apply this product to any purpose not indicated by MOUNTUP.
● Incorrect installation may result in product damage or body injury. MOUNTUP shall
bear no responsibility for any damage or in
jury resulted from incorrect installation,
incorrect assembly or misuse.
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, contact Customer Service via
help@jollyholding.com
5
Safety Caution
2M2M
Band Tape
Drywall with
wood studs?
CAUTION:
Yes --- Perfect!
No --- This mount is NOT compatible.
MAX:
400mm/16"
MAX:400mm/16"
Yes --- Perfect!
No --- This mount is NOT compatible.
4
Installation Tools
(Not Included)
2 Does your TV
(including accessories)
weigh less than
88 LBS (40 KG)?
1 Is your TV VESA
equal to/greater than
75x75mm /3x3" and
equal to/less than
400x400mm/16x16"?
Before getting started, let’s make sure this mount is perfect for you!
88LBS
40KG
Max:
DO NOT install
into drywall alone
Perfect! Perfect!
Wood Stud Install
Concrete Install
- 2 -
Arm and
Wall Plate
Hardware Included
01
x1
This product contains
small items that could be a choking hazard if
swallowed. Before starting assembly, verify
all parts are included and undamaged. If
any parts are missing or damaged, do not
return the damaged item to your dealer;
please contact our customer service team.
Never use damaged parts!
NOTE: Not all parts and hardware included
will be used.
WARNING:
Brackets
02
x2
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4
x4x4
Philips Screws
M8 x 15mm
M8 x 45mm
x4
x4 x8 x4
M-EM-A M-B M-C M-D
M-F M-G
M-H
Spacers
L5mm
x8
M-I
TV Screws / Washers
Hardware
Wall /Product)
5/16 x 2½ in
Lag Bolts
x4
x1
CA
Washers
Ø8mm
x4
B
Open end wrench
- 3 -
STEP 1-1 Select TV
Screw Diameter
Thread screws by hand into the threaded holes on the back of your TV to select which screw
diameter fits your TV.
M6M4
M8
STEP 1-2 Select TV
Screw Length
Correct
Correct
Too Long
Too Short
- 4 -
STEP 1-3
Attach the Bracket
Position your brackets over your TV hole pattern - making sure the brackets are centered
and level over the TV hole pattern.
Secure the brackets using your screw/washer/spacer selection:
(a) for Flat Back
(b) for Round Back / Extra space
CAUTION: Ensure bracket is securely fastened before moving on to the next step.
M-H
M-E
M-C
M-A
(a) Flat Back
M-H
M-G
M-I
M-F
M-D
M-B
(b) Round Back /
Extra Space
Not for M8 screws
Not for M8 screws
- 5 -
STEP 2A
Wall Plate Installation (Wood stud)
2A-1
2A-2
Locate your studs. Verify and
mark the center of the studs by
finding the stud edges using an
awl, a thin nail, or an
edge-to-edge stud finder.
Position the wall plate at
your desired height and line up
the holes with your stud center
line. Level the wall plate and
make the holes.
01
2A-3
7/32 in.
Ø5.5 mm
in. (70 mm)
Drill pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit.
IMPORTANT:
Pilot holes must be
in. (70 mm).
Be sure to drill into the center of the stud.
drilled to a depth of
01
- 6 -
STEP 2B
Wall Plate Installation (Concrete or Brick)
Drill pilot
holes
2B-1
2B-2
2.75in 70 mm
Ø 10 mm
Ø 10 mm
2A-4
01
01
2
01
A
B
01
Install wall plate using lag bolts
and washer . Tighten the lag bolts
until until they are pulled firmly against
the wall plate
A
B
A
01
Position the
wall plate
at your
desired
height , level
the wall plate
and mark the
polit hole
locations.
- 7 -
Concrete Wall
Concrete Wall
01
A
B
01
Install wall plate using lag bolts ,
washer and anchor.
Tighten the lag bolts until they are
pulled firmly against the wall plate
A
01
STEP 3
Lift and hang TV with brackets [02] onto wall bracket [01].
02
02
01
01
Secure TV with brackets against the
horizontal plate with the pre-assembled
screws
Preassembled
screw
- 8 -
Contact us by email help@jollyholding.com to have
these additional pieces shipped directly to you.
Concrete Wall Anchor
4pcs
Concrete wall anchor (NOT INCLUDED)
A
B
± 3°
Adjustments
± 3°
Tilting angle adjustment (+5° / -10°)
Pull TV to your desired angle then fasten tilting nuts with
open end wrench.
Leveling adjustment (-3°/+3°)
If needed, TV can be leveled ±3 degrees via adjusting the 4
nuts with the open end wrench.
- 9 -
C
C
(Tilting)
(Leveling)
±3°
C
- 10 -
Product dimensions:
-
5°
10°
-3°
/+3
°
435.8mm
429.5mm
80mm
359mm
425mm
MAX:400mm
MIN:75mm
MAX:400mm
MIN:75mm
155mm
/
