Roche Virtuoso User manual

Ventana Medical Systems, Inc.

www.ventana.com

Part No.: PL-000123-EN Rev. K

2017 - 05

Virtuoso User Guide, Version 5.5

ii Virtuoso User Guide

Virtuoso User Guide

Copyright

Trademarks

VENTANA, ISCAN, the VENTANA logo, COMPANION ALGORITHM, VIRTUOSO, and VANTAGE are trademarks of Roche. All

other trademarks are the property of their respective owners.

Open Source And Commercial Software

Virtuoso software might contain components or modules that are Open Source or Commercial Software programs. For copyright and

other notices and licensing information regarding such software programs included with the Virtuoso software please see Appendix A

of the reference guide and the product on-line help pages included with the product.

The product and Virtuoso software as a whole may form a regulated device in accordance with the applicable laws – please refer to the

reference guide and the labeling for details. Please note that the respective authorization in accordance with the applicable laws lapse in

case of any unauthorized changes to the Virtuoso software.

Contact Information

Ventana Medical Systems, Inc.

1910 E. Innovation Park Drive

Tucson, AZ 85755

USA

+1 520 887 2155

+1 800 227 2155 (USA)

www.ventana.com

Ventana Medical Systems, Inc.

203 Ravendale Drive

Mountain View, CA 94043

USA

Roche Diagnostics GmbH

Sandhofer Strasse 116

D-68305 Mannheim

Germany

+49 621 7590

Part No.: PL-000123-EN Rev. K iii

Table of Contents

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

About the Virtuoso Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Who Should Read this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Intended Use for Virtuoso Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Related Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Connection Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Cyber Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1: SLIS Software Basic Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Opening the SLIS Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Logging into SLIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Manage Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Adding a New Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Update Case Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Delete a Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Manage Patients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Manage Clients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Manage Physicians . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Manage Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Adding a New User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2: Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Opening the Virtuoso Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Logging into the Virtuoso Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3: Virtuoso Software for Histotechnicians . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Case List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Find Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Filter Case List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Work List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

View Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Stain Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Accept or Reject a Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Specimen List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Release a Specimen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Upload a Gross Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Upload a Radiology Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Upload Miscellaneous Case Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

4: Virtuoso Software for Pathologists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Case List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Find Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Filter Case List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Rearrange Case List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Rearrange Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

View Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Stain Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Create a Field of View or Annotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Perform an FOV Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

iv Ventana Medical Systems, Inc.

Table of Contents Virtuoso User Guide

Accept or Reject an FOV for an Aggregate Score . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Mark an FOV for a Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Manual Override of Aggregated Slide Score . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Draw an Exclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Add Comments for a Slide and FOVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Viewing and Synchronizing Multiple Slides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Specimen List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Reject a Slide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Share a Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Report and Sign-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Sign-Out a Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Generate a Case Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Generate a Specimen Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Post Sign-Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Reopen a Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Make a Case Addendum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Make a Case Amendment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Make a Case Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Part No.: PL-000123-EN Rev. K 1

About the Virtuoso Software

Welcome to the Virtuoso software, a comprehensive web-based pathology solution for viewing, managing, and sharing digitized

glass slides.

Who Should Read this Guide

Histotechnicians and Pathologists should read this user guide and use it for reference while using the Virtuoso software.

Intended Use for Virtuoso Software

The Virtuoso software is a web based pathology solution for viewing, managing and sharing digital glass slides. Virtuoso is an accessory

to iScan systems and allows interfacing with stain scoring and interpretation software algorithms.

NOTE: Images in the Virtuoso Reference Guide are illustrative only and are shown for general training purposes. Please see

the individual stainer user guides for performance characteristics for staining systems that are available for clinical

use.

Related Software

When operating the Virtuoso software without a interface to a laboratory information system, there is an optional module to

manage cases, patients, clients, physicians, and users that appear and are used within the Virtuoso software. This module is the

Virtuoso Simple Laboratory Information System, or SLIS. If using the Virtuoso SLIS module, see “1: SLIS Software Basic

Procedures” on page 3 for more information.

Technical Support

For Virtuoso Technical Support, contact Ventana Medical Systems, Inc.

Connection Requirements

In order to connect to the Virtuoso software, your web browser and workstation must meet the minimum requirements listed in the

following table:

Ventana Medical Systems, Inc.

1910 E. Innovation Park Drive

Tucson, AZ 85755

USA

Tel (USA): +1 800 227 2155; for Technical Support, press 1

Tel: +1 520 887 2155; for Technical Support, press 1

Recommended Minimum

Operating System Windows 7 Professional Windows 7 Enterprise

Supported Browsers Mozilla Firefox 24 ESR, 17 ESR, and

Internet Explorer 9.0

Internet Explorer 8.0

Workstation RAM 4 GB 4 GB

Network Connectivity 1 Gbps Ethernet Network Card 10/100 Mbps Ethernet Network Card

PDF Reader (for generating reports) Adobe Acrobat Reader 11.0.06

Monitor

Minimum resolution requirements 1680x1050

2 Ventana Medical Systems, Inc.

About the Virtuoso Software Virtuoso User Guide

Cyber Security

See the Virtuoso Reference Guide (PL-000092-UK).

Part No.: PL-000123-EN Rev. K 3

1: SLIS Software Basic Procedures

The Simple Laboratory Information System, or SLIS, is a functional module to manage cases, patients, clients, physicians, and

users that appear and are used within the Virtuoso software. The SLIS software is used to manage the Virtuoso software when there

is no interface with a laboratory information system.

Opening the SLIS Software

1. Open a supported Internet browser.

2. Type your SLIS URL (uniform resource locator, or web address) in the Address Bar.

For example: https://<host name>/:8080/slis. Where <host name> is the name of the machine on which the SLIS application

server is installed.

3. Press Enter.

The SLIS software is opened in your browser.

Logging into SLIS

1. In the SLIS Login Screen: Enter your User ID and Password.

2. Click the Login button. The SLIS home page is opened.

After logging into the SLIS software, do not use the browser Back button or the

Backspace key to navigate between windows or views.

4 Ventana Medical Systems, Inc.

1: SLIS Software Basic Procedures Virtuoso User Guide

Figure 1-1. The SLIS Home Page.

NOTE: By default, the SLIS Home Page opens on the Cases tab.

Manage Cases

Adding new cases, updating case information, and deleting cases are performed using the SLIS Cases tab.

Figure 1-2. Cases Tab.

1. Click the Cases tab (see Figure 1-2). The Cases window appears (see Figure 1-3).

Virtuoso User Guide 1: SLIS Software Basic Procedures

Part No.: PL-000123-EN Rev. K 5

Figure 1-3. Cases Window.

Adding a New Case

1. From within the Cases window, select the New button from the SLIS tool bar (see Figure 1-4). The case Information pane

appears (see Figure 1-5).

NOTE: The following procedure assumes the use of a computer mouse when selecting items on drop-down menus but

the tab button and the up and down arrows on the keyboard can be used to perform the same actions.

Figure 1-4. The SLIS Tool Bar.

Add New Case Button

6 Ventana Medical Systems, Inc.

1: SLIS Software Basic Procedures Virtuoso User Guide

Figure 1-5. Case Information Pane.

Virtuoso User Guide 1: SLIS Software Basic Procedures

Part No.: PL-000123-EN Rev. K 7

2. Begin by entering the Accession number in the Case Information section (see Figure 1-6). Field names ending with a red

asterisk (*) are required fields.

Figure 1-6. Case Information.

3. Type information about the patient in the Patient Information section (see Figure 1-8).

IMPORTANT: You can create new patient information by clicking on the Create Patient button. The

Create Patient Screen (see Figure 1-7) is displayed where you can defined a new patient

for the case.

Figure 1-7. Create Patient Screen

Accession #*

Required field. Enter the accession number associated with the case.

Maximum 30 characters.

Lab Site

*

Required field. Type in the first letter of the lab. Select the lab site from the list

that appears.

Date Specimen

Collected

Enter a date in the MM/DD/YYYY format. For example, April 11, 1952 is

entered as 04/11/1952. Or, click on the Calendar button to the right of the field

to select a date from a calendar. Default is the current date or can be blank.

Time Specimen

Collected

Enter a time in the HH:MM AM/PM format. For example, 11:00 AM. Default is

the current date or can be blank.

Primary Tissue Type

*

Required field. Select the tissue type from the drop-down menu.

Tissue Type

Description

This field becomes active based on the tissue type selected. If active, select a

tissue description from the drop-down menu.

External Case ID A unique case identifier.

8 Ventana Medical Systems, Inc.

1: SLIS Software Basic Procedures Virtuoso User Guide

Figure 1-8. Patient Information.

4. Enter the workflow for the case on the Workflow section (see Figure 1-10). Field names ending with a red asterisk (*) are

required fields.

IMPORTANT: You can create a new client, referring and treating physician, and assigned pathologist by clicking on the

appropriate buttons.

Figure 1-9. Create Buttons

Name *

Required field. Type in the patient name. As you type, the system displays a likely match

from the list of existing patients in the system. If the correct patient name is displayed,

select the name from the list with a single mouse click.

To create a new patient, click the Create Patient button.

Patient ID Enter the Patient ID with the patient.

Patient Sex This field will be auto populated from the patient record.

Patient DOB This field will be auto populated from the patient record.

Patient Age This field will be auto populated from the patient record.

Clinical

Indications

Enter the clinical indication(s) for the patient. Maximum 450 characters.

Create New

Patient Button

New

Patient

Button

Create Client

Create Referring Physician,

Physician, and User Buttons

Virtuoso User Guide 1: SLIS Software Basic Procedures

Part No.: PL-000123-EN Rev. K 9

Figure 1-10. Case Workflow Information.

Case Workflow

Required field. Select a workflow type from the drop-down menu.

Integrated View (Treating MD) - Indicates that the lab performs both slide

preparation and diagnosis of the specimen submitted by the treating physician.

Integrated View (Client) - Indicates that the lab performs both slide

preparation and diagnosis of the specimen submitted by the pathologist from an

external lab.

TechView361 - Indicates that the lab performs the slide preparation only of the

specimen submitted by a pathologist from an external lab. The pathologist

performs the diagnosis with the aid of computer-assisted quantitative image

analysis.

TechView342 - Indicates that the lab performs the slide preparation only of the

specimen submitted by a pathologist from an external lab. The pathologist

performs the diagnosis and gives a manual score of the slide.

NOTE: Some fields displayed in this section depend on the chosen workflow

type. In addition, some fields are pre-populated based on existing

information.

Client Name

If the case workflow type is either Integrated View (Client), TechView361, or

TechView342, the client is the external pathology lab associated with the

pathologist submitting the specimen.

Type in the client name. As you type, the system displays a likely match from

the existing list of existing clients. If the correct client name is displayed, select

the name from the list with a single mouse click.

NOTE: To create a new client, click the Create Client button.

10 Ventana Medical Systems, Inc.

1: SLIS Software Basic Procedures Virtuoso User Guide

5. Enter the specimen information for the case on the Specimen Information section (see Figure 1-11). Field names ending with a

red asterisk (*) are required fields.

Referring Physician

If the case workflow type is Integrated View (Treating MD), then the referring

physician is the physician who is treating the patient and submitted the

specimen. If the case workflow type is either Integrated View (Client),

TechView361, or TechView342,the referring physician is the pathologist who

submitted the specimen and works for the external pathology lab (the client).

Type in the physician name. As you type, the system displays a likely match

from the existing list of existing physicians. If the correct physician name is

displayed, select the name from the list with a single mouse click.

NOTE: To create a new referring physician, click the Create Physician button.

Treating Physician

If the case workflow type is Integrated View (Treating MD), then the Treating

Physician field auto populates in this field with the name chosen as the referring

physician.

For the other case workflow types, type in the physician name. As with the

other physician fields, the system displays a likely match from the list of existing

physicians as you type. If the correct physician name is displayed, select the

name from the list with a single mouse click.

NOTE: To create a new physician, click the Create Physician button.

Assigned Pathologist

If the case workflow type is Integrated View (Treating MD) or Integrated View

(Client), then the assigned pathologist is selected from a list of pathologists that

belong to the lab. If the case workflow type is TechView361 or TechView342,

then the assigned pathologist is selected from a list of pathologists that belong

to the external pathology lab (the client)

Select a pathologist from the list.

NOTE: To create a new assigned pathologist, lick the Create User button or

refer to “Adding a New User” on page 19.

Virtuoso User Guide 1: SLIS Software Basic Procedures

Part No.: PL-000123-EN Rev. K 11

Figure 1-11. Specimen Information.

6. Add associated slide images for the case by selecting the Add button on the Slide Information section (see Figure 1-12).

Specimen Number Required field. Enter in the specimen number. For example, A for specimen A.

Date Received

Enter a date in the MM/DD/YYYY format. For example, April 11, 1952 is

entered as 04/11/1952 or appropriate international set default. Or, click on the

Calendar button to the right of the field to select a date from a calendar. Default

is the current date or can be blank.

Time Received

Enter a time in the HH:MM AM/PM format. For example, 11:00 AM. Your default

might be set to the 24 hour clock. Default is the current date or can be blank.

Primary Tissue

If you have a case with multiple tissue types, the primary tissue type is the main

tissue type of interest. For example, if the primary tissue type is breast, another

type of tissue could be lymph node tissue.

Tissue Type

Description

This field becomes active based on the tissue type selected. If active, select a

tissue description from the drop-down menu.

Client Specimen # If available, enter in the client specimen number.

Specimen Description Enter a description of the specimen.

Bar code

A unique bar code either received from an LIS system or manually entered by

the user.

Surgical Procedure Enter a description of the surgical procedure.

Gross Description Enter a gross description of the case. Maximum 450 characters.

12 Ventana Medical Systems, Inc.

1: SLIS Software Basic Procedures Virtuoso User Guide

Figure 1-12. Slide List - Add New Slide Row.

NOTE: To select or change the value for the Test Type, Control, Scoring Type, Clone Type and Vendor, double-click

on the field to display the values. Click on the value (Figure 1-19).

Figure 1-13. Selecting a Field Value

7. To associate an image with the slide, select the Associate Slide Images button in the upper right-hand corner of the Slide

Information section (see Figure 1-14). The Associate Slide Images window appears displaying slide images from the image

server (see Figure 1-15).

NOTE: Use a unique image label ID for each slide image, unless it is a rescan image of the same slide.

Slide # Required field. Enter in the specific slide number.

Block # If available, enter in the specific slide block number.

Test Type Required field. Select the test type from the drop-down menu.

Control Required field. Select the control type from the drop-down menu.

Scoring Type

Required field. Select the scoring type from the drop-down menu. The scoring

types displayed depend on the selected test type.

Clone Type

Select the clone type from the drop-down menu. The clone types displayed are

based on the selected test type.

Comments Enter in a brief comment on the specimen. Maximum 30 characters.

Image File Label

Required field. The field is auto populated once a slide image is associated with

the slide (refer to the next step). If known, you can also directly type in the

image file label.

Image

Once a slide image is associated with the slide, this field provides a preview of

the image.

Vendor

Required field. If an IHC slide, select the vendor of the antibody clone from the

drop-down menu.

External Site ID A unique ID assigned to an external site patient. Maximum 15 characters.

Double-Click

on the Field

Click on the

Value

Virtuoso User Guide 1: SLIS Software Basic Procedures

Part No.: PL-000123-EN Rev. K 13

Figure 1-14. Slide List - Add New Slide Row.

Figure 1-15. Associate Slide Images Window.

8. By default, the list of slide thumbnails displays up to twenty of the most recent slides scanned into the system. You can also

search for slide images in a date range or type in text to search for slides with a matching image file label. Once the desired

thumbnail is located, drag the slide thumbnail to the row on the slide list on the left. The image file label is populated into the

list. Repeat these steps until all slides have an associated image file label. Select the Apply button in the upper left-hand corner

of the window to complete this procedure. The window closes once the slide image is associated (see Figure 1-16).

Figure 1-16. Associate Slide Images Window - Slide Associated.

9. Select the Add button to add additional slide rows (see Figure 1-17).

NOTE: Click on Preview to confirm that a slide has been associated with the slide row.

14 Ventana Medical Systems, Inc.

1: SLIS Software Basic Procedures Virtuoso User Guide

Figure 1-17. New Slide Rows.

10. To add additional specimens in the Specimen Information section of the case, select the Add Specimen Tab (see Figure 1-18)

and repeat the above steps.

Figure 1-18. Specimen Tabs - Add Specimen Tab.

11. When you finish entering the case, select the Save button (see Figure 1-19) from the SLIS tool bar to complete the procedure.

A pop-up window confirms the successful addition of the new case (see Figure 1-20).

Figure 1-19. The SLIS Tool Bar - Save Button.

Add a Slide Row

Add Specimen Tab

Save Button

Virtuoso User Guide 1: SLIS Software Basic Procedures

Part No.: PL-000123-EN Rev. K 15

Figure 1-20. New Case Entered.

16 Ventana Medical Systems, Inc.

1: SLIS Software Basic Procedures Virtuoso User Guide

Update Case Information

1. From within the Cases window, select an existing case from the Case List pane (see Figure 1-21). The case information is

displayed in the Case Information pane.

Figure 1-21. Select an Existing Case.

2. Update the case information as needed.

3. When done, select the Save button from the SLIS tool bar to complete the procedure (see Figure 1-22). A pop-up window

confirms the successful update of the case information

Figure 1-22. The SLIS Tool Bar - Save Button.

Delete a Case

Deleting a case in SLIS deletes the case in the Virtuoso software, but only if all specimens on the case have NOT been released in

the Virtuoso software. If this condition is met, then the case is deleted from the Virtuoso software.

You can also completely remove a case in the Virtuoso software even if it has a specimen already released, for example, if you have

some test cases that you need to delete prior to going production. Or you may have entered the wrong data on a case and just want

to completely start over again and re-use the accession number.

CAUTION: The case is completely removed from both SLIS and the Virtuoso software. The delete is recorded in

the audit log including date, time stamp and user who did the deletion.

1. From within the Cases window, select an existing case from the Case List pane (see Figure 1-23).

Figure 1-23. Select an Existing Case.

2. Select the Delete button from the SLIS tool bar to delete the case (see Figure 1-24).

Save Case Information Button

Page is loading ...

Roche Virtuoso User manual

Roche Virtuoso User manual

Related papers

Other documents