Baja X250 Xmoto Extreme Setup Instructions

Brand: Baja

Model: X250 Xmoto Extreme

Category: Rechargeable batteries

Type: Setup Instructions

X250 Dirt Bike Set Up Instructions

Removal from crate

1. Remove cardboard carton.

2. Remove metal frame and parts included.

Parts and Hardware

Gas cap and vent tube

Side fender

Number plate

Tools

Battery acid

Rear foot brake pedal

Handlebar

3. Attach rear foot brake pedal to lever.

Bolt size 6mm QTY 2. Torque bolts 6-8ft lbs

(8-11Nm)

Bolts

4. Attach handlebar to forks using allen head screw. Be sure to

place spacer between handlebar clamp and fork.

Screw size 8mm QTY 4. Torque bolts 15-18 ft.lbs (20-25Nm)

Spacer

Ignition Switch

Number plate

5. Attach ignition switch assembly to handlebars

and attach electrical plug to wire harness.

Screw size 6mm QTY 2

6. Attach number plate

Bolt size 6mm QTY 2

Side covers

Gas cap

7. Attach left and right side fenders.

Bolt size 6mm QTY 6 (3per side)

8. Twist gas cap onto gas tank.

Battery

WARNING

The following procedure is very dangerous and should be performed with utmost

care and attention. Wear protective eye wear, rubber gloves, and have water available

should electrolyte come in contact with skin or eyes. KEEP ALL CHILDREN AWAY FROM

THE AREA WHILE THIS PROCEDURE IS BEING PERFORMED.

POISON – CAUSES SEVERE BURNS

Contains sulfuric acid.

Avoid contact with skin, eyes, or clothing

To prevent accidents, rinse empty container with water.

ANTIDOTE:

External – ush with water

Internal – Call physician immediately. Drink large quantities of water or milk.

Follow with milk of magnesia, beaten eggs or vegetable.

Eyes – Flush with water for 15 minutes and get prompt medical attention.

KEEP OUT OF REACH OF CHILDREN.

9. Remove bolt holding rear side fender

and seat to frame. Remove battery

Battery

Preparing the battery:

· Place battery on level surface. Remove sealing tape

from top. (see gure 1)

· Take the electrolyte container out of the plastic bag.

· Place electrolyte container upside down with the sealed

silver mouths of the electrolyte bottles in line with the

six ller holes of the battery. (see gure 2)

· Push the container down strongly enough to break the

silver seals. (see gure 3)

· As electrolyte starts owing into battery, air bubbles

will come up from the mouths of the plastic electrolyte

bottles.

· Leave bottles upside down in battery holes until

electrolyte is completely drained.

· Never leave children unattended around battery.

· If air bubbles cease to oat to the top of the electrolyte

bottles, tap lightly on top.

· DO NOT remove container from battery while it is

draining.

· Never cut or pierce electrolyte container.

· After all the electrolyte has drained from the bottles

into the battery, pull plastic electrolyte bottles gently

out of the battery.

· Discard empty electrolyte bottles in a waste area that is

inaccessible to children and animals.

· After lling let battery stand for at least 30 minutes

before charging. This allows the electrolyte to penetrate

plates for optimum performance and ensures longer

battery life.

· After 30 minutes the battery is ready for its initial

charge. Place cap strip loosely over the lling holes as

shown in the picture. (see gure 4)

Figure 1

Figure 2

Figure 3

Figure 4

Battery

How to Initially Charge the battery:

1. Connect the red positive (+) cable to the red positive (+)

pole of the battery.

(see gure 5)

2. Connect the black negative (-) cable to the black negative

(-) pole of the battery. (see gure 6)

Note: The red positive (+) cable has a larger diameter than

the black negative y cable.

3. Charging rate: Charge battery @ 0.7 Amps for

5 ~ 10 hours.

• After charging is complete, press down rmly with

both hands to seat the caps. (Do not pound or

hammer.) The battery is now sealed. (see gure 7 )

• Once battery is rmly seated in battery compartment

attach the red positive wire to the red positive terminal

on the battery.

• Then attach the black negative wire to the black

negative terminal on the battery.

WARNING

NEVER REMOVE THE STRIP OF CAPS NOR ADD ANY

WATER OR ELECTROLYTE.

Figure 5

Figure 6

Figure 7

Black (-)

Red (+)

Gas and Oil

10. Fill gas tank as specied in

owners manual.

11. Refer to owners manual for

proper starting instructions.

!!WARNING!!

This engine may be shipped with oil in it. This oil

should be drained and replaced with new engine

oil as described in the owners manual. Never

attempt to start the engine without rst replacing

the engine oil with the proper amount and grade

as described in the owners manual.

Baja X250 Xmoto Extreme Setup Instructions

Brand: Baja

Model: X250 Xmoto Extreme

Category: Rechargeable batteries

Type: Setup Instructions

Download PDF

report

Baja X250 Xmoto Extreme Setup Instructions

Baja X250 Xmoto Extreme Setup Instructions

Related papers

Other documents