Kichler Lighting 83340CG User manual

Brand
Kichler Lighting
Model
83340CG
Type
User manual
IS-83340-US
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
1) Lower shade[N] down over frame and secure to frame by aligning two (2) tabs on
shade with two (2) tabs on frame and screwing threaded nials[O] through holes in
aligned tabs.
2) Pass xture wires from coupling[L] on top of frame through long threaded tube[P]
and then through decorave tube[Q]. Screw threaded tube into coupling.
3) Lower decorave tube down over long threaded tube. Pass xture wires through
decorave cap[R] and then through coupling[S].
4) Lower decorave cap onto decorave tube, ensuring threads on long threaded tube
inside decorave tube protrude through hole in center of decorave cap.
5) Screw coupling[S] onto threads protruding out of the top of decorave tube[Q].
Tighten coupling to secure decorave tube and decorave cap.
6) Pass xture wires through desired number of stems[M] and supplied short threaded
tubes[K], and screw stems together using short threaded tubes.
NOTE: Thread locking compound must be applied to all stem threads as noted with
symbol (4) to prevent accidental rotaon of xture during cleaning, relamping, etc.
7) Screw rst stem into coupling using a short threaded tube.
8) Pass xture wires from last stem through short threaded tube[K] and through loop[I].
Screw short threaded tube into top of last stem and into loop.
9) Take threaded pipe[A] from parts bag and screw in screw collar loop[B] a minimum
of 6 mm (1/4”). Lock into place with hexnut[C].
10) Run another hexnut down threaded pipe almost touching rst hexnut. Now screw
threaded pipe into mounng strap[D]. Mounng strap must be posioned with
extruded thread faced into outlet box[E]. Threaded pipe must protrude out the back
of mounng strap. Screw third hexnut onto end of threaded pipe protruding from
back of mounng strap.
11) Connect mounng strap[D] to outlet box using the strap mounng screws[J].
12) Unscrew the threaded ring[F] from screw collar loop. Take canopy[G] and pass over
screw collar loop. Approximately one half of the screw collar loop exterior threads
should be exposed. Adjust screw collar loop by turning assembly up or down in
mounng strap. Remove canopy.
13) Aer desired posion is found, ghten both top and boom hexnuts up against the
boom and top of the mounng strap.
14) Slip canopy over screw collar loop and thread on threaded ring. Aach open chain
link[H] (with xture connected) to boom of screw collar loop. Close the open link by
wrapping with a towel and squeezing closed using pliers. Unscrew threaded ring, let
canopy and threaded ring slip down.
15) Pass electrical wire and ground wire through chain link[H], threaded ring[F], canopy,
screw collar loop, and threaded pipe.
16) Wrap supply ground wire (BARE COPPER OR GREEN) around ground screw aached
to mounng strap and ghten screw. Be sure to leave extra wire beyond ground
screw to make connecon with ground wire from xture (no less than 2”).
17) Connect driver neutral input wire (WHITE) to supply neutral wire (WHITE) using P4
(YELLOW) wire nut.
18) Connect driver live input wire (BLACK) to supply hot wire (BLACK) using P4 (YELLOW)
wire nut.
19) Using a P4 (YELLOW) wire nut, connect xture ground wire (BARE COPPER) to supply
ground wire (aached to the mounng strap ground screw).
20) Connect xture neutral wire (BLUE or BLACK) to driver neutral output wire (BLUE or
BLACK) using P3 (ORANGE) wire nut.
21) Connect xture live wire (RED) to driver live output wire (RED) using P3 (ORANGE)
wire nut.
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main fusebox before starng and
during the installaon.
WARNING:
This xture is intended for installaon in accordance with the Naonal Electrical Code
(NEC) and all local code specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
CLEANING:
• Always be certain that electric current is turned o before cleaning.
• Only a so damp cloth should be used. Harsh cleaning products may damage
the nish.
Installaon Instrucons
[A] Threaded Pipe
[B] Screw Collar Loop
[C] Hexnut
[D] Mounting Strap
[E] Outlet Box
[F] Threaded Ring
[G] Canopy
[H] Chain Link
[I] Loop
[J] Strap Mounting
Screws
[K] Short Threaded Tubes
[L] Coupling
[M] Stem
[N] Shade
[O] Threaded Finials
[P] Long Threaded Tube
[Q] Decorative Tube
[R] Decorative Cap
[S] Coupling
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired operaon.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will
not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Informaon:
For warranty informaon please visit: kichler.com/warranty
22) Raise canopy to ceiling.
NOTE: Be certain wires do not get pinched between mounng strap and canopy, or
canopy and ceiling.
23) Secure canopy in place by ghtening threaded ring onto screw collar loop.
WIRING DIAGRAM
LIVE (HOT) WIRE (+DC)
FROM FIXTURE (RED)
GROUND WIRE FROM FIXTURE
(BARE COPPER)
NEUTRAL WIRE (-DC) FROM FIXTURE
(BLUE OR BLACK)
LIVE (HOT) OUTPUT WIRE (+DC)
FROM DRIVER (RED)
NEUTRAL OUTPUT WIRE (-DC)
FROM DRIVER (BLUE OR BLACK)
SUPPLY GROUND WIRE
(BARE COPPER OR GREEN)
NEUTRAL INPUT WIRE (-AC)
TO DRIVER (WHITE)
LIVE (HOT) INPUT WIRE (+AC)
TO DRIVER (BLACK)
SUPPLY GROUND WIRE
(BARE COPPER OR GREEN)
SUPPLY NEUTRAL WIRE
(WHITE)
CANOPY
DRIVER (ATTACHED
TO CANOPY)
OUTLET BOX
P4 WIRE NUT
(YELLOW)
P3 WIRE NUT
(ORANGE)
P4 WIRE NUT
(YELLOW)
P3 WIRE NUT
(ORANGE)
P4 WIRE NUT
(YELLOW)
SUPPLY HOT WIRE
(BLACK)
K
M
►
►
►
M
►
B
F
H
►
I
K
G
C
A
E
D
J
O
N
S
R
Q
P
L
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kichler Lighting 83340CG User manual

Brand
Kichler Lighting
Model
83340CG
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents