ClearWater Lights Low Beam User manual

Brand
ClearWater Lights
Model
Low Beam
Category
Motorcycle Accessories
Type
User manual

This manual is also suitable for

Page 1
Specs and Parts List
The Glendina makes your motorcycle more visible to oncoming traffic
during the day, and at night provides a wide pattern of light for more side
illumination. They are a combination of a fog and visibility lights meant to
make you more conspicuous. If you ride mostly on the street, during the day,
Glendina is a good choice to help make you safer and more visible. This
universal Glendina kit can fit over 300 bikes!
Please be sure to read our instructions thoroughly
before attempting installation.
Modes: Low Beam/High Beam
LEDs: Three LEDs (ea)
Brightness: 900 Lm on High Beam, 200 Lm on Low Beam (ea)
Power: 10W/1A on High Beam (ea), 1W/0.1A on Low Beam (ea)
Optic: Driving Beam
Size: 1.8” Diameter
Weight: 4 oz (ea)
Page 3
Mounting The Lights
• First, park the motorcycle on hard pavement or concrete to insure the
bike will be stable during the installation. If you can mount the bike on a
stand with tie-down straps, this will help secure the motorcycle.
• Follow the manufacturers guidelines for disconnecting the battery. This is
important to prevent damage to the electrical system.
• Pre-assemble the lights to the mounting brackets using the shoulder
washers (if needed), along with the spacers and new bolts. Add 1 or 2
plastic washers to shoulder washer to make up difference in thickness of
front fender if needed. Make sure to assemble one side at a time.
• Gently screw all bolts in hand tight. Inspect the bolt length and spacer
alignment before tightening the bolts. Follow the pictures below as a
reference.
• The mounting bracket can be mounted facing down (shown) or up to
give the desired adjustability range.
Page 2
Page 4
Wiring
• Be sure to route wires so that they cannot become tangled or caught
in either a suspension or steering component. Check movement of both
steering and suspension before riding the bike.
• It is helpful to follow existing wire routing.
Page 3
High Beam Feature:
When your Glendina lights are installed, they will run at a lower brightness
setting when the motorcycle headlight is switched to low, and 100%
brightness when the motorcycle headlight is switched to high.
• Before connecting wires together on the lights and bike, be sure to
disconnect the negative terminal from the battery first, then the positive
terminal.
• Use the wiring diagram on Page 4 as reference.
• Connect small red wires coming out of lights with a Posi-tap to a switched
hot wire. This means one that turns off with the key. A low beam wire coming
from the headlight assembly can often be used. Make sure both red wires
are connected to the Posi-tap together. Refer to the Posi-tap installation
instructions on Page 5.
• Connect small black wires coming out of lights with a Posi-tap to a ground
wire coming out of the headlight assembly. Or any ground on the bike.
• Connect small yellow wires coming out of lights with a Posi-tap to a high
beam wire (Voltage when high beam is switched on) coming out of the
headlight assembly.
Page 5
Wiring Diagram
Page 4
Page 5
How To Use Posi-Taps
1. Strip black sleeve
back 2.5” and strip the
six wires back 0.5”
2. Twist common
colored wires together.
6. Unscrew the gray cap
of the Posi-Tap.
7. Twist the two common
coloed wires backwards
so when threading the
grey cap back on, the
wires will be in a relaxed
state and not twisted.
3. Completely unscrew
bottom cap from Posi-Tap.
4. Feed the twisted
wires through the bottom
portion of the Posi-Tap.
5. Hold onto the base to
ensure the wires do not
slip out of the bottom of
the Posi-Tap, attach to
Posi-Tap body and tighten.
8. Slide the wire you wish
to tap into through the slot
in the cap.
9. Re-attach the body of
the Posi-Tap and tighten,
this will relax the twist
applied in step 7.
Page 7
Aligning The Lights + Tips
Ask an assistant to help you with this procedure. Make sure the bike is on
level ground and have an assistant sit on the bike. Press a level against the
face of the light, and adjust its angle.
The goal is to adjust the lights so that the light is level with the ground.
Passengers and luggage may alter the alignment of the light, so further
adjustments may be needed. You may find that a slight downward angle (5
degrees) is helpful.
Page 6
Do Not Kink The Grommet
Do Not Kink The
Grommet
To maintain the
integrity of the water
sealling grommet,
do not kink, deform
or put pressure on
the grommet when
dressing the wires
during install of
Clearwater Lights.
Page 8
Step 1: Parts List and Bike Preparation
Revised 2/15/21
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ClearWater Lights Low Beam User manual

Brand
ClearWater Lights
Model
Low Beam
Category
Motorcycle Accessories
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents