ClearWater Lights BMW G310R User manual

Brand: ClearWater Lights

Model: BMW G310R

Category: Motorcycle Accessories

Type: User manual

ClearWater Lights BMW G310R are designed to enhance your riding experience with brighter, safer lighting. These lights feature multiple brightness levels, controlled by a handlebar-mounted dimmer switch, allowing you to adjust the intensity to suit different riding conditions. The lights also integrate with your motorcycle's high beam and horn, automatically switching to full brightness when activated. Installation involves mounting the lights to your motorcycle's fender and connecting the wiring harness to your battery and electrical system.

Page 2

Parts List and Bike Preparation

Check Parts list below with your kit to be sure all parts are handy. If

something is missing, please call us at (916) 852-7029.

Please be sure to read our instructions thoroughly

before attempting installation.

Page 1

Page 3

Page 2

Disassembly

Remove the left and right side bolts pointed out above with a

Phillips screwdriver.

Phillips ScrewdriverPhillips Screwdriver

The headlight assembly will pivot downward, as shows above.

Bike Preparation:

First, park the motorcycle on hard pavement or concrete to insure the

bike will be stable during the installation. If you can mount the bike on a

stand with tie-down straps, this will help secure the motorcycle.

Follow the manufacturers guidelines for disconnecting the battery. This is

important to prevent damage to the electrical system.

Remove the rear seat.

Page 4 Page 3

Remove the two M6 bolts as shown above on both sides of the

bike. It is helpful to remove the bolts and install our bracket on one

side at a time.

Mount the Darlas to the fender mount as shown above.

5mm Hex Key5mm Hex Key

M5x40 SH (4) M6x14 SHCS Bolt

M6 Flat Washers(4)

#14 Spacer

M5 Flat Washer

Mounting the Lights

Page 5

Page 4

Wiring Diagram

NOTE: Before proceeding with wiring the lights, take a moment to

review the wiring diagram. Keep the diagram handy throughout the

installation.

Page 6

Mounting the Dimmer

Page 5

Mounting The Volume Control Knob: (Bar Mount)Mounting The Volume Control Knob: (Bar Mount)

Mount the dimmer to the handlebar using the provided pot

hardware. Follow the photos above for mounting details.

Route the dimmer wire along factory wires to the harness

mounting location (behind the headlight assembly). Use zip ties to

secure in place.

Page 7

Mounting the Harness

Wire Routing:

Be sure to route wires so that they cannot become tangled or caught

in either a suspension part or steering part. Check movement of both

steering and suspension before riding the bike.

It is sometimes helpful to follow existing wire routing.

Using included zip ties, mount the wiring harness (small black box) to the

area behind the headlight assembly. Reference photo below for harness

mounting location and wiring path for power wires.

Page 6

With the fuse holder removed, route the black and red power cables from

the Clearwater Lights harness through the wiring trough. Using a pull tool

will make this easier.

Mount relay harness inside hereMount relay harness inside here Attach power terminals to battery hereAttach power terminals to battery here

Page 8

Switched Hot, High Beam & Horn

Page 7

Tap white wire from volume control knob to this yellow wire.

Tap thin red wire from relay Tap thin red wire from relay

harness to this orange wireharness to this orange wire

Switched Hot Wire: Locate the auxiliary plug and tap the thin RED wire from

the harness to the ORANGE wire as shown below. This tells our harness

when to turn on and off with the key.

High Beam Wire: Remove the rubber boot from the headlight connector,

exposing the 3-wire plug underneath. Using the included Posi-tap, connect

the thin WHITE wire from the harness to the YELLOW wire at the headlight

connector. This will tell our lights to go to 100% when the high beam is on.

Horn Wire: Using a posi-tap, connect one of the white wires from the harness

to the hot wire of the horn. This will tell our lights to go to 100% when the

horn is pressed.

Ensure all wires are free from pinch points and direct heat. Connect the

dimmer to the harness (green connectors).

Page 9

Finishing the Install

Aligning the Lights:

Ask an assistant to help you with this

procedure. Make sure the bike is on

level ground and have an assistant sit

on the bike. Press a level against the

face of the light, and adjust its angle.

The goal is to adjust the lights so that

the light is level with the ground.

Passengers and luggage may alter

the alignment of the light, so further

adjustments may be needed. You

may find that a slight downward angle

(5 degrees) is helpful.

Page 8

Do Not Kink The Grommet

Do Not Kink The

Grommet

To maintain the

integrity of the water

sealling grommet,

do not kink, deform

or put pressure on

the grommet when

dressing the wires

during install of

Clearwater Lights.

Connect the RED power wire to the fuse included in your kit, then attach it

to the positive terminal on the battery. Connect the BLACK power wire to the

negative terminal on the battery.

Test your lights. The bike needs to be on, engine running for our system to

work properly. Ensure the lights dim when in low beam, and go to 100%

when the high beam or horn are pressed.

Page 10

Notes

Page 9

Page 11

Notes

Page 10

Revised 11/5/21

ClearWater Lights BMW G310R User manual

Brand: ClearWater Lights

Model: BMW G310R

Category: Motorcycle Accessories

Type: User manual

Download PDF

report

ClearWater Lights BMW G310R User manual

ClearWater Lights BMW G310R User manual

Related papers

Other documents