George Kovacs P5436-697-L User manual

Brand
George Kovacs
Model
P5436-697-L
Category
Motorcycle Accessories
Type
User manual

The George Kovacs P5436-697-L is a stylish and versatile lighting fixture that offers a range of features for customized illumination. With its adjustable frames, you can direct the light to create the perfect ambiance for your space. Installation is straightforward, allowing you to mount it securely to your ceiling. The fixture supports dimming functionality using compatible wall dimmers, enabling you to adjust the brightness level to suit your needs or mood.

The George Kovacs P5436-697-L is a stylish and versatile lighting fixture that offers a range of features for customized illumination. With its adjustable frames, you can direct the light to create the perfect ambiance for your space. Installation is straightforward, allowing you to mount it securely to your ceiling. The fixture supports dimming functionality using compatible wall dimmers, enabling you to adjust the brightness level to suit your needs or mood.

Fig. 3
INSTALLATION INSTRUCTIONS
Item#P5436-697-L & P5437-697-L (Rev. 04/26/2022)
READ AND SAVE THESE INSTRUCTIONS
WA R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION
1.
Carefully remove the fixture from the carton and check that all parts
are included as shown in the illustration.
2.
Shut off power at the circuit breaker and remove the old fixture
including the mounting hardware.
MOUNTING THE FIXYURE (Fig. 1)
3.
Attach mounting plate (A) to junction box (not included) using
mounting screws (B) (Size: #8-32N*L1”L) as shown in Fig. 1.
Noted: The side of mounting plate (A) marked “GND” must face
out.
4.
Determine the desired hanging height and thread rods (F1, F2 and
F3) to all thread on fixture body. Carefully pass wires through
each rod during assembly. Secure swivels (G) onto rods (F1).
5.
Slide metal plate (E) and canopy (D) followed by lock washers
(H) over swivels (G) and secure with hex nuts (I) via wrench (J)
(not included).
CONNECTION THE WIRES (Fig. 2)
6.
There is one driver inside canopy, connect driver output wire to LED
wires as listed below. Secure with wire connectors (I).
-Red driver output wire (labeled Output+) to red LED wire (labeled LED+)
-Yellow driver output wire (labeled Output-) to yellow LED wire (labeled LED-)
7.
Connect the electrical wires as shown in Fig. 2, making sure that all
wire connectors are secured. If your junction box has a ground wire
(green or bare copper), connect the fixtures ground wire to it.
Otherwise, connect the fixture ground wire directly to the mounting
plate (A) using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
FINISHING THE INSTALLATION (Fig. 1)
8.
Align canopy (D) over mounting plate (A) and secure with
screws (C).
9.
Adjust each frame on the fixture body as Fig.3. Fig.2
Note:Illustration (Fig. 1) on this manual is for installation purpose
only. It may or may not be identical to the fixture purchased.
Dimmable with ELV and/or LED compatible wall dimmer switch.
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Black
(Hot)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or
Bare
Copper(G
round)
Page: 1/2
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY
A QUALIFIED ELECTRICIAN TO ENSURE PROPER
WIRING AND INSTALLATION.
P5436-697-L & P5437-697-L
Outlet box
Fig. 1
Set#XXXX
-
Mounting plate
-
Ground screw
-
Mounting Screw*2
-
Swivel*2
A
H
I
B
D
J
C
E
G
F1
F2
F3
Rod#
-
XXXX*2 (F1)
-
XXXX*4 (F2)
-
XXXX*2 (F3)
Fixture body
Fig.4
a. Hardware Bag
A. Mounting Plate*1
D.Canopy*1
E.Metal plate*1
C.Mounting screw*2
G.Swivel*2
b. Hardware Bag:
F1. ROD 6"*2
F2. ROD 12"*4
F3. ROD 12"*2
Page: 2/2
P5436-697-L & P5437-697-L
A
D
C
E
G
F2
F3
F1
  • Page 1 1
  • Page 2 2

George Kovacs P5436-697-L User manual

Brand
George Kovacs
Model
P5436-697-L
Category
Motorcycle Accessories
Type
User manual

The George Kovacs P5436-697-L is a stylish and versatile lighting fixture that offers a range of features for customized illumination. With its adjustable frames, you can direct the light to create the perfect ambiance for your space. Installation is straightforward, allowing you to mount it securely to your ceiling. The fixture supports dimming functionality using compatible wall dimmers, enabling you to adjust the brightness level to suit your needs or mood.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents