Modern Forms PD-87956 Harmonix Operating instructions
- Type
- Operating instructions
1
INSTALLATION INSTRUCTIONS
879 - LED PENDANT
PD-87956
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
Wire Connector
Qty:4pcs+1Extra
Mounting Screw
Qty:1Extra
Wood Screw
Qty: 4pcs+1Extra
Φ
4
Plastic Anchor
Qty:4pcs+1Extra
A
Wire Connector
Qty:3pcs+1Extra
Rod
Qty:12"x6pcs
+6"x2pcs
BCDEF
HARDWARE
2
INSTALLATION INSTRUCTIONS
879 - LED PENDANT
PD-87956
FIG. 1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1. Shut o the power at the circuit breaker and remove existing xture,including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
3. Remove the mounting screws (D) and mounting back plate from the xture.
4. Drill holes in the wall aligned with the key-hole location in the mounting back plate, insert the plastic anchors (E).
5. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box. Fasten it to the
ceiling using the wood screws (F). Note: the side of the mounting plate marked “GND” must face out.
6. Unscrew the hex nuts, take out the swivels. Choose suitable rods for desired length. Thread the xture wires through the rods, swivels,
canopy, washers, ground wire, safety cord brackets and hex nuts.Then make sure all are tightened.
Wire connector
Mounting Backplate
Driver input wire
Mounting screw
Canopy
Rod
Swivel
Hex nut
Safety cord
Junction box
B
D
Plastic Anchor
E
A
Wood screw
F
Driver(2pcs)
LD-1200MA50U-DI-IS
Wire connector
C
Washer
Safety cord bracket
Ground wire
Driver output wire
Junction box screw
FIG. 4 Mounting Backplate Dimensions
FIG. 3 Driver Wiring
3
INSTALLATION INSTRUCTIONS
879 - LED PENDANT
PD-87956
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement progr
am. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
7. Connect the driver’s output wires (shown in Fig. 3) to xture wires as shown in Fig. 2, making sure that all wire connectors (C) are secured.
One driver connect to one xture wire, red wire to red, and black to black. After all output wires connected, tidy the wires in the canopy.
8. Hook the safety cords to the mounting back plate slot.
9. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (B) are secured. If your outlet
box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to
the back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
10. Secure the xture to the mounting back plate using the mounting screws (D) .
11. For slope ceiling application, rotate swivel at the top of the stem to ensure luminaries are aiming down (Fig.4).
Note: The xture exceeds 28lbs, and must be installed using an outlet box U.L. approved for up to 100lbs.
12. This xture features electronic low voltage (ELV) or 0-10V dimming capabilities. See notes below for specic dimming wires information.
13. To utilize ELV dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
14. To utilize 0-10V dimming: use wire purple (dim+), pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.
161
2"
Ø31
2"
Ø23
4"
41
2"
113
4"
81
4"
Turn to down
23
4"
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
Purple - Dim+
Pink or Gray - Dim-
Red - Fixture+
Black - Fixture-
Black - Hot
White - Neutral
-
1
-
2
-
3
Modern Forms PD-87956 Harmonix Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Modern Forms BL-54307 Nexus Operating instructions
-
-
WAC Lighting FM-W46205 Squat Operating instructions
-
WAC Lighting FM-W47206-35-BK Operating instructions
-
-
-
-
-
-
Other documents
-
George Kovacs P1336-665-L User manual
-
-
circa LIGHTING RL 2092 User manual
-
-
superbrightleds com LHBD3 Series User manual
-
-
-
-
-
