Dometic GP-ISW-R User manual

Dometic
Brand
Dometic
Model
GP-ISW-R
Category
Power adapters & inverters
Type
User manual

Dometic GP-ISW-R is a remote control for GP-ISW inverters that allows you to switch them on and off remotely. It displays battery bank voltage, output power, and error and action conditions. The remote can be used to:

  • Turn the inverter on or off
  • Monitor the battery bank voltage
  • Monitor the output power
  • Identify error conditions (High Battery, Low Battery, Over Temperature, Overload)
  • Identify action conditions (INV, POWER SAVING, GRID) Compatible with GP-ISW700/1000/1500/2000/3000/4000 inverters.

Dometic GP-ISW-R is a remote control for GP-ISW inverters that allows you to switch them on and off remotely. It displays battery bank voltage, output power, and error and action conditions. The remote can be used to:

  • Turn the inverter on or off
  • Monitor the battery bank voltage
  • Monitor the output power
  • Identify error conditions (High Battery, Low Battery, Over Temperature, Overload)
  • Identify action conditions (INV, POWER SAVING, GRID) Compatible with GP-ISW700/1000/1500/2000/3000/4000 inverters.
gpelectric.com
GP-ISW-R
15
14
13
12
11
10
®
PURE SINE
WAVE INVERTER
REMOTE
User Manual
GP-ISW-R (12/24)
© 2021 Go Power!
Worldwide Technical Support and Product Information gpelectric.com
Go Power! | Dometic
201-710 Redbrick Street Victoria, BC, V8T 5J3
Tel: 1.866.247.6527
80325_MANUAL_ISW-R_RevB
[page 2] | gpelectric.com
2. FEATURES...........................................................................................................2
3. SPECIFICATION ..................................................................................................2
4. INTRODUCTION .................................................................................................3
4.1 FRONT PANEL INTRODUCTION.............................................................3
4.2 REAR PANEL INTRODUCTION ...............................................................5
2. FEATURES
The GP-ISW-R remote allows the switching on and off of any GP-ISW inverter from a remote location.
The LED display indicates the following:
• Battery bank voltage display
• Output power display
• Error condition indicator (High Battery, Low Battery, Over Temperature, Over Load
conditions)
• Action condition indicator (INV, POWER SAVING, GRID)
3. SPECIFICATIONS
SPECIFICATION ITEM GP-ISW-R-12/24
Input Voltage 10.5 ~ 66VDC
Operating Temperature Range 0 ~ 40°C
Storage Temperature Range -30°C ~ 70°C
Standby Current Draw < 80mA
Compatible Inverters GP-ISW700/1000/1500/2000/3000/4000
CONTENTS
gpelectric.com | [page 3]
4.1 FRONT PANEL INTRODUCTION
gpelectric.com
GP-ISW-R-12
15
14
13
12
11
10
®
1
3 2
4
11 POWER ON/OFF BUTTON
Power ON/OFF button turns the inverter on or off.
2OUTPUT POWER INDICATOR
Output power indicator shows the power draw from the inverter by the load. Ideally,
the output power indicator should remain in the green & orange area of the bar chart.
If the output power indicator is up to the red area, the OLP LED will ash and the inverter
will shut down.
Power ON/OFF button Battery voltage indicator
Output power indicator Other indicators
11 3
2 4
Note: the 24 volt inverter remote’s Battery volt-
age indicator reads “20, 22, 24, 26, 28, 30.”
4. INTRODUCTION
[page 4] | gpelectric.com
3
4
BATTERY VOLTAGE INDICATOR
Battery voltage indicator will move up and down as the battery voltage changes.
Ideally, the voltage should remain in the green area of the bar chart.
If the voltage goes into the red area at the top and bottom of the bar chart, the
inverter may shut down.
OTHER INDICATORS
• OVP (Over voltage protection):
•
Indicates that the inverter will shut down because its input voltage is above
the voltage limit.
• UVP (Under voltage protection):
•
Indicates that inverter will shut down because its input voltage is below the
voltage minimum.
• OLP (Overload protection indicator):
•
Indicates the inverter will shut down due to a short circuit or overload protection.
• OTP (Over temperature protection indicator):
•
Indicates the inverter will shut down due to over temperature protection. Once
the inverter cools down, the indicator will turn off automatically.
• INV indicator:
• Indicates the inverter is ready.
• PWR. SAV. indicator:
• Power saving functions are described below:
LED MEANING INVERTER OUTPUT
Solid Ready ON
Flashing Active OFF
Off Inactive
• GRID indicator:
Indicates the AC Grid is connected to the inverter (only functional when
connecting inverter series with Transfer Relay).
INTRODUCTION
gpelectric.com | [page 5]
4.2 REAR PANEL INTRODUCTION
89
76
Ø4.5
77
10.5
6.5 72
AUX
22±1.0
10±0.5
Ø4.5±0.3
5
6
7
5AUX PORT
Note: the AUX port is only used in work trucks.
The connector (shown above) attached to AUX wire (AWG 14 or 16) must be
connected with a 12V / 0.5A fuse.
• Ignition Lockout function:
Turns OFF the inverter when the auxiliary input wiring is connected to the
ACC with 12 volts.
• Return Override function:
Turns ON the inverter when the auxiliary input wiring is connected to the
reversed gear shift with 12 volts.
Connector
AUX port JP1
Phone jack connector
5 7
6
INTRODUCTION
[page 6] | gpelectric.com
6PHONE JACK CONNECTOR
1. Before connecting, make sure to switch the inverter to REMOTE mode.
2. Connect the RJ-11 cable between the ISW-R remote and the inverter.
WARNING!
DO NOT use a standard telephone cable.
A
6
1
B
6
1
9.6±0.2
9.6±0.2
12.4±0.3
6.5±0.2
14.6±0.3
3.1±0.2
12.4±0.3
6.5±0.2
14.6±0.3
3.1±0.2
A
6
5
4
3
2
1
WIRE COLOR
YELLOW
BLUE
GREEN
WHITE
BLACK
RED
B
6
5
4
3
2
1
INTRODUCTION
gpelectric.com | [page 7]
7JP1
The JP1 is to set either the Return Override function or the Ignition Lockout function.
• JP1 jumper “Short” - Return Override function:
• Turns ON the inverter when the auxiliary input wiring is connected to the
reversed gear shift with 12 volts.
• JP1 jumper “Open” - Ignition Lockout function:
•
Turns OFF the inverter when the auxiliary input wiring is connected to the
ACC with 12 volts.
•
The connector which is connected to AUX power must be used with a
12V / 0.5A fuse.
TRIGGERED SIGNAL JP1 INVERTER STATUS
AUX
1 Open OFF
0 Open ON
1 Short ON
0 Short OFF
Note: default mode is Open.
INTRODUCTION
© 2021 Go Power!
Worldwide Technical Support and Product Information gpelectric.com
Go Power! | Dometic
201-710 Redbrick Street Victoria, BC, V8T 5J3
Tel: 1.866.247.6527
80325_MANUAL_ISW-R_RevB
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Dometic GP-ISW-R User manual

Dometic
Brand
Dometic
Model
GP-ISW-R
Category
Power adapters & inverters
Type
User manual

Dometic GP-ISW-R is a remote control for GP-ISW inverters that allows you to switch them on and off remotely. It displays battery bank voltage, output power, and error and action conditions. The remote can be used to:

  • Turn the inverter on or off
  • Monitor the battery bank voltage
  • Monitor the output power
  • Identify error conditions (High Battery, Low Battery, Over Temperature, Overload)
  • Identify action conditions (INV, POWER SAVING, GRID) Compatible with GP-ISW700/1000/1500/2000/3000/4000 inverters.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents