ML Accessories TRKSP7BCCW User manual

ML Accessories
Brand
ML Accessories
Model
TRKSP7BCCW
Type
User manual

This manual is also suitable for

ML Accessories TRKSP7BCCW is a dimmable LED track light fitting, designed for use with either a 230V or 50Hz power supply. It features a modern, sleek design with a white finish and has an IP20 rating, making it suitable for indoor use only.

With a versatile design, this fitting can be used in a variety of applications, such as shops, offices, and homes. It provides focused lighting thanks to the included 24° reflector, which can be easily replaced if desired.

Installation is simple and straightforward, with the fitting requiring an earth connection for safe operation. The included instructions provide clear guidance on how to wire the end cap, ensuring correct polarity. The fitting is then easily attached to the track by pushing it into place and rotating it 90° anti-clockwise.

ML Accessories TRKSP7BCCW is a dimmable LED track light fitting, designed for use with either a 230V or 50Hz power supply. It features a modern, sleek design with a white finish and has an IP20 rating, making it suitable for indoor use only.

With a versatile design, this fitting can be used in a variety of applications, such as shops, offices, and homes. It provides focused lighting thanks to the included 24° reflector, which can be easily replaced if desired.

Installation is simple and straightforward, with the fitting requiring an earth connection for safe operation. The included instructions provide clear guidance on how to wire the end cap, ensuring correct polarity. The fitting is then easily attached to the track by pushing it into place and rotating it 90° anti-clockwise.

90
INSTALLATION & MAINTENANCE MANUAL
TRKSP7xxx
230V
50Hz
IP
20
1
These instructions should be read carefully and retained after installation by the end user for future
reference and maintenance.
These instructions should be used to aid installation of the following products:
TRKSP7BCW/TRKSP7BCCW/TRKSP7WCW/TRKSP7BWW/TRKSP7BCWW/TRKSP7WWW
GENERAL INSTRUCTIONS
SAFETY
INSTALLATION
• Installation of this product should only be carried out by a qualified electrician or competent person
to the latest Building and current IEE Wiring Regulations (BS7671)
• Please isolate mains prior to installation/maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the
rating of the circuit cable, fuse or circuit breaker
• Please note the IP (Ingress of Protection) rating of this luminaire when deciding the location for
installation
• This product is Class I and requires an earth
• This product series is IP20 rated
• This product is dimmable
Live End
Terminal cover
screw
Rear entry
knock out
• If this product is to be used with a dimmer, please check compatibility with dimmer manufacturer
prior to installation
• Choose a suitable location to mount the track ensuring the surface will be able to support the
weight of the track and fittings
• Provide power to the required point of installation
• Drill the holes ensuring not to infringe with any joists, gas / water pipes or electrical cables
• Remove the securing screw to remove the Live End from the track (See Fig 1)
Fig 1
2
SECURING SCREW LIVE END
L N
Neutral (blue)
Live (brown)
Earth (green & yellow)
• Remove the terminal cover screw from the Live End to gain access to the mains connections
• Choose the method of cable entry - either rear entry (metal back) or side entry (plastic)
• Wire the end cap and ensure the correct polarity is observed. Live (brown), Neutral (blue) and Earth
(green and yellow) (see Fig 2)
3
L N
Fig 2
Fig 3
• Ensure that the Dead End Connector is on the track and connect the Live End to the track
• Fix fitting to track as shown in Fig 3
The Polarity groove
is a shallow groove
on the surface of the
track. It is only on
one side of the track.
• Push track fitting into the track
ensuring the polarity groove is on the
correct side and the pins are lined up
correctly as shown
• Rotate fitting anti-clockwise 90° and
gently pull back sliding cover until it
locks into place (see Fig 4)
Twin pins
Fig 4
• Switch on power supply and
check for correct operation
Single pin
Sliding cover
ML Accessories Group Limited
LU5 5TA
www.mlaccessories.co.uk AKSEPT17_V4
4
The LEDs fitted in this product are non-replaceable. The unit should be recycled in the correct
manner when it reaches the end of its life. Check local authorities for where facilities exist.
Subject to the surface foundation material, ensure the correct fixings are used.
The Live End will only fit on one end of the track. Putting the Live End on the incorrect end may
damage the track and fitting.
TRKSP7R - (24° reflector). To replace, unscrew front bezel, remove existing reflector and replace
with TRKSP7R reflector
This product must be disconnected from the circuit if subjected to any high voltage or insulation
resistance testing. Irreparable damage will occur if this instruction is not followed.
This product has a warranty of 3 year from date of purchase. Failure to install this product in
accordance with the current edition of the IEE Wiring regulations, improper use or removal of the
batch codes will invalidate the warranty. If this product should fail within its warranty period it
should be returned to the place of purchase for a free of charge replacement. ML Accessories does
not accept responsibility for any installation costs associated with the replacement product. Your
statutory rights are not affected. ML Accessories reserve the right to alter product specification
without prior notice.
GENERAL
WARNING
ADDITIONAL ACCESSORIES
WARRANTY
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ML Accessories TRKSP7BCCW User manual

ML Accessories
Brand
ML Accessories
Model
TRKSP7BCCW
Type
User manual
This manual is also suitable for

ML Accessories TRKSP7BCCW is a dimmable LED track light fitting, designed for use with either a 230V or 50Hz power supply. It features a modern, sleek design with a white finish and has an IP20 rating, making it suitable for indoor use only.

With a versatile design, this fitting can be used in a variety of applications, such as shops, offices, and homes. It provides focused lighting thanks to the included 24° reflector, which can be easily replaced if desired.

Installation is simple and straightforward, with the fitting requiring an earth connection for safe operation. The included instructions provide clear guidance on how to wire the end cap, ensuring correct polarity. The fitting is then easily attached to the track by pushing it into place and rotating it 90° anti-clockwise.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents