INSTALLATION & MAINTENANCE MANUAL
TRK8270xx / TRK8271xx
These instructions should be read carefully and retained after installation by the end-user for
future reference and maintenance.
These instructions should be used to aid the installation of the following products:
TRK8270xx / TRK8271xx
GENERAL INSTRUCTIONS
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)
and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the
circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
SAFETY
INSTALLATION
• Provide powered track to the required point of installation
• The side of the track with the earthing conductor has a shallow polarity groove on the surface on one side
the of the track to help identify which way round to insert the accessories (see Fig. 1)
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end-user for future reference and
maintenance.
These instructions should be used to aid the installation of the following products:
TRK8270XX / TRK8271XX
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
INSTALLATION
• Provide powered track to the required point of installation
• The side of the track with the earthing conductor has a shallow polarity groove on the surface on one
side the of the track of the track to help identify which way round to insert the accessories (see Fig. 1)
Fig. 1
• Align the arrows on the track pendant with the polarity groove on the track, push into the track and rotate
anti-clockwise (see Fig. 2).
Fig.2
• Insert a suitable E27 lamp
• Switch on and check for correct operation
Polarity groove
Fig. 1
• Align the arrows on the track pendant with the polarity groove on the track, push into the track and rotate
anti-clockwise (see Fig. 2).
INSTALLATION & MAINTENANCE MANUAL
These instructions should be read carefully and retained after installation by the end-user for future reference and
maintenance.
These instructions should be used to aid the installation of the following products:
TRK8270XX / TRK8271XX
SAFETY
• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations
(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician
• Please isolate mains prior to installation or maintenance
• Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of
the circuit cable, fuse, or circuit breaker
• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation
• This product is for indoor use only
• This product is Class I and must be earthed
• This product is IP20 rated
INSTALLATION
• Provide powered track to the required point of installation
• The side of the track with the earthing conductor has a shallow polarity groove on the surface on one
side the of the track of the track to help identify which way round to insert the accessories (see Fig. 1)
Fig. 1
• Align the arrows on the track pendant with the polarity groove on the track, push into the track and rotate
anti-clockwise (see Fig. 2).
Fig.2
• Insert a suitable E27 lamp
• Switch on and check for correct operation
Polarity groove
Fig. 2
• Insert a suitable E27 lamp
• Switch on and check for correct operation
• The cable drop can be shortened by removing the two screws on the base of the of the track adaptor and
opening the base (see Fig. 3)
• The cable drop can be shortened by removing the two screws on the base of the of the track adaptor
and open the base (see Fig3.)
Remove the 2 screws
Fig.3
• Remove the 2 screws from the Live and Neutral terminals (see Fig. 4)
Fig.4
• Loosen the plastic screw on the side of the pendant adapter and pull the cable through to the desired
length, cut the cable and re-attach to the Live and Neutral terminals with crimps (not provided)
• Tighten the plastic screw on the side of the pendant adapter and refit the base and fasten down the
two screws
• Insert into a track, switch on and check for correct operation
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type.
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the
current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate
the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase
for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs
associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right
to alter product specification without prior notice.
• Remove the 2 screws from the Live and Neutral terminals (see Fig. 4)
• The cable drop can be shortened by removing the two screws on the base of the of the track adaptor
and open the base (see Fig3.)
Remove the 2 screws
Fig.3
• Remove the 2 screws from the Live and Neutral terminals (see Fig. 4)
Fig.4
• Loosen the plastic screw on the side of the pendant adapter and pull the cable through to the desired
length, cut the cable and re-attach to the Live and Neutral terminals with crimps (not provided)
• Tighten the plastic screw on the side of the pendant adapter and refit the base and fasten down the
two screws
• Insert into a track, switch on and check for correct operation
GENERAL
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type.
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with the
current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate
the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase
for a free of charge replacement. ML Accessories does not accept responsibility for any installation costs
associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve the right
to alter product specification without prior notice.
• Loosen the plastic screw on the side of the pendant adapter
and pull the cable through to the desired length, cut the cable
and re-attach to the Live and Neutral terminals with crimps
(not provided)
• Tighten the plastic screw on the side of the pendant adapter
and refit the base and fasten down the two screws
• Insert into a track, switch on and check for correct operation
Fig. 3
Fig. 4
This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities
for where facilities exist.
Clean with a soft dry cloth only, do not use aggressive cleaning products or solvents which may damage the
product.
This product is dimmable dependent on lamp type.
GENERAL
WARRANTY
This product has a warranty of 1 year from date of purchase. Failure to install this product in accordance with
the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will
invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place
of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation
costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve
the right to alter product specification without prior notice.
AKJUL21_V1
ML Accessories Limited LU5 4LT
www.mlaccessories.co.uk
101
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
INTERNATIONAL
CONTACT DETAILS
-
1
-
2
-
3
-
4
-
5
-
6
ML Accessories TRK8271BK User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ML Accessories TRKIT8ABC User manual
-
-
-
-
-
-
-
-
ML Accessories BL5BK User manual
-
Other documents
-
Hampton Bay EC8715ABZ Operating instructions
-
Hampton Bay EC636ABZ User guide
-
Hampton Bay EC400WH Operating instructions
-
Vaillant TURBOmax VUW 242 E Instructions For Installation And Servicing
-
-
Hampton Bay 16033KIT1-WH Operating instructions
-
Knightsbridge CBL22BK 22W 370lm 3000K 1000mm LED Bollard User manual
-
Wonderfire BR00290 SONNET Installer's Manual
-
Worcester Greenstar 25Si Installation And Servicing Instructions
-
Eterna SDPHO Safety And Installation Instructions Manual
