luminii LineLED LL-RGB-RGBW-X18-Pixel Installation guide

luminii
Brand
luminii
Model
LineLED LL-RGB-RGBW-X18-Pixel
Type
Installation guide

This manual is also suitable for

REV0.1 11012023
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
LLX18-RGBW 24V - Installation Instructions
Please read complete instruction prior to installation and keep for future reference!
Models LLX18-RGBW-, LLX18X2-RGBW- 7777 N. Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations. Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0.
Attention: Always test LLX18-Pixel before installing. Connect LLX18-Pixel to power supply to
ensure it is working properly and no damage has occured during shipping.
1 2
HST - aluminum
heat sink tape
Clean the area thoroughly where the LLX18-RGBW will be
installed. Use the included Heat Sink Tape for installation of
LLX18-RGBW on non-aluminum and non-copper surfaces to
ensure proper heat dissipation. LLX18-RGBW may not reach
it’s rated average life when installed otherwise.
LLX18-RGBW
paper
backing
LLX18-RGBW
wire leads
solder
pads
Remove the paper backing
from the LLX18-RGBW and
firmly press down making
sure there are no air bub-
bles that can cause surface
irregularities. Do not remove
the adhesive, removing the
adhesive may cause arcing of
the Line LED tape.
ripple
Soldered joints
NOTE - When removing backing & laying
LLX18-RGBW to surface avoid installing with
ripples & bending over 90°.
NOTE - Avoid sharp bends
or bending on the solder
joints near 1” on wire lead.
3
If required for installation, cut the LLX18-Pixel strip between two
rows of solder pads. Always cut LLX18-Pixel from end without
connector / wire leads.
REV0.1 11012023
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
LLX18-RGBW 24V - Installation Instructions
Please read complete instruction prior to installation and keep for future reference!
Models LLX18-RGBW-, LLX18X2-RGBW- 7777 N. Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
[email protected]
www.luminii.com
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit. Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations. Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
6. Conforms to UL STD 2108. Certified to CSA STD C22.2 No.250.0.
WIRING DIAGRAM
SR-DMX-SPI
Smart Pixel LineLED Decoder
24V-
24V+
PIXEL LED
In
Out
(-)
(+)
POWER SUPPLY
(N)
(L)
CONTROLLER WIRES
1000 ft max,
decoder to Controller
AC
input
output
24VDC
32 ft max, decoder to strip
Before wiring, ensure power is off to power
supply
Also, ensure that the correct power supply (voltage
and wattage) is used to power the LED strips
connected to the decoder. Follow illustrated wiring
diagram. Use screwdriver to open and close
connection slots.
24V-
24V+
24V-
24V+
NOTE: When connecting two or more LED strip lights or light fixtures, always make sure the signal direction arrows
are pointing to same direction
The signal direction arrow should appear on each section (cut increment) of LED strip
Signal direction arrow Signal direction arrow
NOTE: Must power from the opposite direction of the signal direction arrow
NOTE: Please make sure that
power is turned off before wiring.
Also, ensure that the correct power
supply (voltage and wattage)
is used to power the LED strips
connected to the decoder. Follow
illustrated wiring diagram. Use
screwdriver to open and close
connection slots.
  • Page 1 1
  • Page 2 2

luminii LineLED LL-RGB-RGBW-X18-Pixel Installation guide

luminii
Brand
luminii
Model
LineLED LL-RGB-RGBW-X18-Pixel
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents