REV0.7 11012023
LineLED 24V - Installation Instructions
Models LLDW68-
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit.
Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations.
Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 1 of 3
LineLED
Attention: Always test LineLED operation before installing.
Connect LineLED to power supply to ensure it is working
properly and no damage has occured during shipping.
2 3
If length of LineLED needs to be adjusted on site, simply
cut the LED strip in between solder pads. Always cut from
end with no wire leads.
solder pads
Always ensure power to power supply is off! Follow
diagrams on page 2 to connect power feed wires to power
supply.
Clean the area thoroughly where the LineLED will
be installed.
Remove the paper backing from the LineLED and
firmly press down making sure
there are no air bubbles that can cause surface
irregularities. Do not remove the
adhesive, removing the adhesive may cause
arcing of the Line LED tape.
1
LineLED
adhesive tape
NOTE - When removing backing & laying
LineLED to surface avoid installing with ripples
& bending over 90°.
NOTE - Avoid bending
near 1” on both side of the
soldered joints.
ripple
Soldered joints
REV0.7 11012023
LineLED 24V - Installation Instructions
Models LLDW68-
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit.
Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations.
Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 2 of 3
Wiring Diagrams
+
WW
CW
DMX cables
(For DMX cable, use
Belden 9829, 9842
or CAT5 shielded
twisted pair cabling or
equivalent)
Load
Ground
Neutral
INPUT
120 - 277VAC
D-
D+
GND
to the next
LED Driver
To Controller
DYNAMIC WHITE
LineLED
Operations to Controller
120 - 277VAC
24V DC+
24V DC-
Load
Ground
Neutral 120 - 277VAC
To on/off Switch
INPUT
DYNAMIC WHITE
LineLED
RGBW-RC-R
RGBW Receiver
PSDMX-3X96-24
DMX LED Driver
DDW-MC
Wireless Controller
PSV-XX-24-U2ND-XX
Non Dimming LED
power supply
Using DMX LED power supply
Using non dimming LED power supply, receiver and controller
REV0.7 11012023
LineLED 24V - Installation Instructions
Models LLDW68-
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit.
Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations.
Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 3 of 3
Load
Ground
Neutral
+
–
DYNAMIC WHITE
LineLED
PS010WD-96-24
Warm Dim LED Driver
Using warm dim LED power supply
Using tunable white LED power supply
120 - 277VAC120 - 277VAC
Controller 1:
0-10V for intensity
Controller 2:
0-10V for color
temperature
INPUT
+
–
+
–
Load
Ground
Neutral
DYNAMIC WHITE
LineLED
PS010TW-96-24
Tunable White LED Driver
REV0.7 11012023
LineLED 24V - Installation Instructions
Models LLDW68-
Please read all instructions prior to installation and keep for future reference!
1. Product should be installed by a qualified electrician.
2. Prior to installation ensure power is off at fuse box to prevent electrical shock.
3. Use only with Class 2 power unit.
Utiliser seulement avec Classe 2 unite d’alimentation electrique.
4. Suitable for Damp Locations.
Convient Aux Emplacements Humides.
5. For under-cabinet or shelf mount.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATIONS WITHOUT NOTICE
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
www.luminii.com
Page 4 of 3
24V DC+
24V DC-
Load
Ground
Neutral
To on/off Switch
120 - 277VAC
INPUT
DYNAMIC WHITE
LineLED
DDMX-RGBW
DMX Decoder
PSV-XX-24-U2ND-XX
Non Dimming LED
power supply
Using non dimming LED power supply and decoder
24V DC+
24V DC-
Load
Ground
Neutral
To on/off Switch
120 - 277VAC
INPUT
DYNAMIC WHITE
LineLED
PSV-XX-24-U2ND-XX
Non Dimming LED
power supply
DDMX-RGBW
DMX Decoder
DW-DMX
Dynamic White
DMX Controller
Using non dimming LED power supply, decoder and controller
/
