LED WORLD LIGHTING LS2 RGB-W LED Receiver User manual

Brand
LED WORLD LIGHTING
Model
LS2 RGB-W LED Receiver
Type
User manual
LS2 - RGBW Color Receiver
LS2 OPERATION OVERVIEW
This product is rated for indoor installation and only for dry locations. Do not install in washrooms or areas near water (or the possibility of in
the future).
Ensure applicable wire is installed between driver, xture, and any controls in between. When choosing wire, factor in voltage drop, amperage
rating and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires and cause re.
Wiring diagrams in this installation guide for basic installations. Please carefully review your installation before proceeding with a qualied
electrician familiar with low voltage wiring techniques.
Do not modify this product beyond the instructions in this guide or the warranty will be voided.
This product is intended to be installed and serviced by a qualied licensed electrician. Install in accordance with the National Electric Code,
and local regulations.
Securely mount the LS2 using the two mounting points at each end.
Only power with a regulated (listed) constant voltage Class 2 power supply (12-24V DC).
SAFETY & WARNINGS
BEFORE YOU BEGIN, READ ALL WARNINGS AND INSTALLATION INSTRUCTIONS (AS THEY MAY HAVE BEEN UPDATED FROM PREVIOUS VERSIONS ).
IMPROPER INSTALLATION(S) PRESENT HAZARDS, WHICH CAN RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.
1/3
INTRODUCTION
5 in 1 (RGB, RGBW, CCT, RGB+CCT and single color) controller is the wireless controller works with wireless remote FUT089. The LS2
controller features mesh network and auto-synchronizing function with brightness, CCT, RGB, RGBW and RGB+CCT output mode. LS2
controller uses 2.4GHz wireless technology. It consumes less power, transmits signal over a long distance and it is anti-interference.
23mm (0.9”)
Input 1 Input 2
124mm (4.88”)
38mm (1.49”)
Indicator light Output mode switch
White
Yellow
Red
Green
Blue
Single color mode
Dual White Mode
RGB Mode
RGBW Mode
RGB+CCT Mode
Indicator light color instruction:
Input voltage
Output
Compatible remote control
Remote Distance
DC12V-DC24V Class 2 Regulated
5A/channel, Max 5A
FUT089
22.8m (75 Feet) Clear line of sight
Working temperature
Dimension
-20°C~40°C (-4°F~104°F)
L124mm(4.88”) × W38mm(1.49”) × H23mm(0.9”)
LS2 TECHNICAL SPECIFICATIONS
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
1-800-387-4081
ledworldlighting.com ledworld.ca |
Copyright © 2022 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.1 09/29/2022
WIRING DIAGRAM
L
N
AC Power
50/60Hz
Class 2 Low Voltage Regulated Driver
(match Voltage with LED Strip Voltage)
G
N
L
t
u
p
n
I
t
u
p
t
u
O
V+
V-
RGB LED Strip
Diagram-1 : Hardwired connection to a RGB LED Fixture
[+]
[B]
[G]
[R]
Recommended 14~20 AWG cord
+-
Make sure that
wires cannot
cross
+-
Make sure that
wires are screwed tight
and fully inserted
wrong correct
Warning: Input voltage must be identical to output voltage of the LED Fixture!
Exposed wire should not be more than 6- 8 mm long & solder tip (tinned). Do not allow Wires to cross and insure all exposed
wire is fully inserted into the screw terminals. Hand tighten screw terminals. Use 22 to 16 AWG gauge wire for output
terminals.
WIRE 6-8MM (0.25-0.30”)
Hardwired wiring
LS2 RGB Receiver
RGB LED Strip
Diagram-2 : Plug-in connection to a RGB LED Fixture
[+]
[B]
[G]
[R]
Recommended 14~20 AWG cord
Wiring with a Plug-in Driver
LS2 RGB Receiver
Class 2 Low Voltage Regulated Driver
AC Power
50/60Hz
(match Voltage with LED Strip Voltage)
MESH NETWORK
75ft (22.8m)
Clear line of sight
Controllers can send signals to another controller within 75ft (22.8m) distance
creating a mesh network.
75ft (22.8m)
Clear line of sight
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
LS2 - RGBW Color Receiver
1-800-387-4081
ledworldlighting.com ledworld.ca |
2/3 Copyright © 2022 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.1 09/29/2022
RGB FIXTURE WIRING DIAGRAM
RGB LED Strip
[+]
[B]
[G]
[R]
LS2 RGBW Receiver
RGBW FIXTURE WIRING DIAGRAM
RGBW LED Strip
[+]
[B]
[G]
[R]
LS2 RGBW Receiver
SINGLE COLOR FIXTURE WIRING DIAGRAM
Single Color LED Strip
[V+]
[V-]
LS2 RGBW Receiver
CCT ADJUSTABLE FIXTURE WIRING DIAGRAM
CCT adjustable LED Strip
[+]
[WW]
[CW]
LS2 RGBW Receiver
RGB+CCT FIXTURE WIRING DIAGRAM
RGB+CCT LED Strip
[+]
[B]
[G]
[R]
LS2 RGBW Receiver
[W]
W
V-
V+
CW
WW
CW
WW
[CW]
[WW]
PAIRING/UNPAIRING WITH FUT089 REMOTE CONTROLLER
ŸCheck the indicator light on LS2 receiver according to connected LED xture. (eg. For RGB mode indicator light should be red). Touch the color
wheel to make sure that device is paired and changes the color.
ŸBefore pressing anything on the FUT089 remote controller, press “I” button on the desired zone 3 times quickly. Connected LED xture light will
blink 3 times when the pairing is done.
ŸTurn OFF LS2 receiver by disconnecting the power, then turn ON by reconnecting the power after about 5 seconds.
Note: If you have to control multiple receivers synchronously, each receiver should be paired according to the above steps.
Pairing:
Unpairing:
ŸBefore pressing anything on the FUT089 remote controller, press “I” button on desired zone you wish to unpair 5 times quickly. Connected LED
xture light will blink 10 times when the receiver is unpaired.
ŸTurn OFF LS2 receiver by disconnecting the power, then turn ON by reconnecting the power after about 5 seconds.
Zone On (I) button
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
™
LED W RLD
INC
ledworldlighting.com | ledworld.ca
SwitchIndicator light
Made in China
Model No.: LS2
Working Temperature: -20~60
Input Voltage: DC12V~24V
Output: 3A/Channel
Total Max input: 5A
2.4G wireless controller
Use only with regulated Class 2
power source
5 IN 1 Smart LED Controller
RGB+CCT Mode
RGBW Mode
RGB Mode
Indicating lamp
show output mode
Dual White Mode
Green
Blue
Red
Yellow
Single Color ModeWhite
Note: Changing a receiver to a different zone can be done using the above steps. Unpair it rst from current zone, then
pair it to new zone number.
LS2 - RGBW Color Receiver
1-800-387-4081
ledworldlighting.com ledworld.ca |
3/3 Copyright © 2022 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 2.1 09/29/2022
  • Page 1 1
  • Page 2 2
  • Page 3 3

LED WORLD LIGHTING LS2 RGB-W LED Receiver User manual

Brand
LED WORLD LIGHTING
Model
LS2 RGB-W LED Receiver
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents