Sauder Entertainment Credenza Installation guide

Sauder
Brand
Sauder
Model
Entertainment Credenza
Type
Installation guide
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Enlish p 1-24
Français p 23-25
Español p 26-28
Lot # 362999 06/25/14
Purchased: __________________
Be sure to ive us a rin before
makin any returns. 1-800-523-3987
Entertaining what
entertains you.
Entertainment Credenza
Camarin Collection | 414802
Table of Contents Assembly Tools Required
Part Identifi cation
Hardware Identifi cation
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
WARNING
!
Skip the power trip.
This time.
3
4
5-22
23-25
26-28
29-30
31
Use of a TV that is too heavy or lare is hazardous. A TV that is too heavy will create a risk of a tip-over that can cause severe injury or
death. A TV that is too lare for the available space miht be accidentally pushed or bumped o the furniture, or subject to tip-over.
• Check the size and weiht of your TV. Compare it to the diaram below – before you begin assembly!
• This Sauder unit is desined for use with televisions weihin less than 95 pounds. Never use with a TV that weihs more.
• The size of the television, front-to-back and side-to-side, must fi t within the space defi ned in the diaram.
• Never place the front ede of the TV past the front ede of the TV support shelf (or stop moldin – if equipped)
• Never allow the sides of the TV to extend past the side edes of the TV support surface.
• If the TV has a CRT picture tube, the picture tube cone may extend past the rear of the support shelf.
• Be sure to apply the warnin label as instructed in the last assembly step. The label provides important safety related information.
47-1/4"
19-1/2"
26-1/2"
414802 www.sauder.com/servicesPae 2
Part Identifi cation
å While not all parts are labeled, some of the parts will have a label or an inked letter on the ede
to help distinuish similar parts from each other. Use this part identifi cation to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C RIGHT UPRIGHT (1)
D LEFT UPRIGHT (1)
D16 RIGHT DRAWER SIDE (2)
D17 LEFT DRAWER SIDE (2)
D73 DRAWER BACK (2)
D720 DRAWER BOTTOM (2)
E UPRIGHT (1)
F TOP (1)
G BOTTOM (1)
H SHELF (1)
I BACK (1)
J ADJUSTABLE SHELF (1)
K FRONT SKIRT (1)
L SIDE SKIRT (2)
M DRAWER FRONT (2)
R
LEFT FRONT/RIGHT REAR
FOOT (2)
S
RIGHT FRONT/LEFT REAR
FOOT (2)
T CENTER FOOT (2)
A
B
C
D
E
F
G
H
I
J
K
L
L
M
M
R
R
S
S
T
D16
D16
D17
D17
D73
D73
D720
D720
414802www.sauder.com/services
Pae 3
Hardware Identifi cation
å Screws are shown actual size. You may receive extra hardware with your unit.
METAL BRACKET - 3
DD
GOLD 1" MACHINE SCREW - 2
MM
BLACK 9/16" LARGE HEAD SCREW - 35
NN
CAM COVER - 4
GG
OO
GOLD 5/16" FLAT HEAD SCREW - 16
METAL PIN - 10
HH
FF
SLIDE CAM - 4
BLACK 1-15/16" FLAT HEAD SCREW - 10
KK
NAIL - 48
PP
LL
BLACK 1-9/16" FLAT HEAD SCREW - 8
HIDDEN CAM - 10
Y
CAM DOWEL - 10
Z
KNOB - 2
EE
AA
CORNER CAP - 1
BB
FOOT BRACKET - 1
35GA
CABINET RIGHT - 2
35GB
CABINET LEFT - 2
35GC
DRAWER RIGHT - 2
35GD
DRAWER LEFT - 2
CC
CORNER BRACKET - 4
RUBBER SLEEVE - 4
II
(Refer to step __ for proper location and application)
WARNING LABEL - 1
JJ
WARNING
Never use this furniture with a TV that is too
large or too heavy. Severe injury or death
can occur. The TV and furniture will be
unstable and may tip.
-The TV must less than 95 lbs.
-The base of the TV must be able to sit
completely on this shelf.
-Refer to instruction book for complete
safety information.
Note: This is a permanent label. Do not try
to remove. Surface will be damaged.
02/ 02 269227
414802 www.sauder.com/servicesPae 4
Step 1
Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
Arrow
Y
Z
(10 used)
(10 used)
Arrow
Y
Z
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
Do not tihten the HIDDEN CAMS in this step.
å
Assemble your unit on a carpeted fl oor or on the empty
carton to avoid scratchin your unit or the fl oor.
å
Push ten HIDDEN CAMS (Y) into the ENDS (A and B),
RIGHT UPRIGHT (C), and SHELF (H). Then, insert a CAM
DOWEL (Z) into each HIDDEN CAM.
A
B
C
H
414802www.sauder.com/services
Pae 5
å
Fasten the CABINET RIGHTS (35GA) and CABINET
LEFTS (35GB) to the RIGHT END (A) and RIGHT
UPRIGHT (C). Use eiht GOLD 516" FLAT HEAD
SCREWS (OO) throuh holes #1 and #3.
Step 2
1
2
3
1
2
3
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
OO
1
2
3
1
2
3
Roller end
Roller end
Finished ede
Rounded ede
414802 www.sauder.com/servicesPae 6
Remember:
Rihty tihty.
Lefty loosey.
A
C
å
Fasten the LEFT END (B) to the TOP (F). Tihten two
HIDDEN CAMS.
å
Insert two METAL PINS (HH) into the UPRIGHT (E).
å
Insert the METAL PINS in the end of the UPRIGHT (E) into
the holes in the TOP (F).
Step 3
Surface
with holes
B
E
F
HH
Finished ede
Rounded ede
Rounded ede
Surface with
HIDDEN CAMS
Start Tighten
Arrow
Minimum
190 derees
Caution
Risk of damae or
injury. HIDDEN CAMS
must be completely
tihtened. HIDDEN
CAMS that are not
completely tihtened
may loosen, and parts
may separate. To
completely tihten:
Arrow
Maximum
210 derees
414802www.sauder.com/services
Pae 7
å
Fasten the SHELF (H) to the LEFT END (B). Tihten two
HIDDEN CAMS.
å
Fasten the SHELF (H) to the UPRIGHT (E). Use two
BLACK 11516" FLAT HEAD SCREWS (KK).
Step 4
B
E
H
Arrow
Minimum
190 derees
Maximum
210 derees
Surface with
HIDDEN CAMS
KK
BLACK 1-15/16" FLAT HEAD SCREW
(2 used in this step)
414802 www.sauder.com/servicesPae 8
Finished ede
å
Fasten the RIGHT UPRIGHT (C) to the SHELF (H).
Tihten two HIDDEN CAMS.
å
Insert two METAL PINS (HH) into the LEFT UPRIGHT (D).
å
Insert the two METAL PINS (HH) in the end of the LEFT
UPRIGHT (D) into the holes in the SHELF (H).
Step 5
Arrow
Minimum
190 derees
Maximum
210 derees
Surface with
HIDDEN CAMS
Finished ede
HH
C
D
H
Surface
without holes
414802www.sauder.com/services
Pae 9
å
Fasten the RIGHT END (A) to the TOP (F) and SHELF (H).
Tihten four HIDDEN CAMS.
Step 6
Arrow
Minimum
190 derees
Maximum
210 derees
Surface with
HIDDEN CAMS
Rounded ede
A
F
H
414802 www.sauder.com/servicesPae 10
å
Fasten the BOTTOM (G) to the ENDS (A and B) and
UPRIGHTS (C and D). Use eiht BLACK 11516" FLAT
HEAD SCREWS (KK).
Step 7
Rounded ede
Surface
with more
holes
KK
BLACK 1-15/16" FLAT HEAD SCREW
(8 used in this step)
414802www.sauder.com/services
Pae 11
A
B
C
D
G
å
Fasten four CORNER BRACKETS (CC) to the FEET (R and S).
Use eiht BLACK 916" LARGE HEAD SCREWS (NN).
å
Then, fasten the FEET (R and S) to the SIDE SKIRTS (L).
Use eiht BLACK 916" LARGE HEAD SCREWS (NN).
Step 8
L
L
R
R
R
R
S
S
S
S
Finished ede
BLACK 9/16" LARGE HEAD SCREW
(16 used in this step)
NN
414802 www.sauder.com/servicesPae 12
CC
CC
CC
CC
å
Insert two METAL PINS (HH) into the FRONT SKIRT (K).
å
Insert the METAL PINS (HH) in the FRONT SKIRT (K) into
the FEET (R and S).
å
Fasten the SIDE SKIRTS (L) and FEET (R and S) to
the BOTTOM (G). Use eiht BLACK 916" LARGE
HEAD SCREWS (NN).
Step 9
BLACK 9/16" LARGE HEAD SCREW
(8 used CORNER BRACKETS)
NN
G
K
L
R
R
S
S
HH
HH
414802www.sauder.com/services
Pae 13
L
Step 10
å
Fasten three METAL BRACKETS (DD) to the FRONT
SKIRT (K) and BOTTOM (G). Use six BLACK 9/16" LARGE
HEAD SCREWS (NN)
BLACK 9/16" LARGE HEAD SCREW
(6 used in this step)
NN
DD
G
K
414802 www.sauder.com/servicesPae 14
å
Fasten the FOOT BRACKET (BB) to the BOTTOM (G).
Use three BLACK 916" LARGE HEAD SCREWS (NN).
å
Slide the CENTER FEET (T) onto the FOOT BRACKET (BB)
and place the CORNER CAP (AA) into the rooves in the
CENTER FEET (T). Then, fasten the FOOT BRACKET (BB)
to the CENTER FEET (T). Use two BLACK 916" LARGE
HEAD SCREWS (NN).
å
NOTE: There are no pre-drilled holes in the CENTER
FEET. The screws will tihten into the rooves.
Step 11
G
BB
AA
T
Groove
BLACK 9/16" LARGE HEAD SCREW
(5 used FOOT BRACKET)
NN
414802www.sauder.com/services
Pae 15
Don't worry. It isn't
Rome. This can be built
in a day.
å
Carefully turn your unit over onto its front edes. Unfold
the BACK (I) and lay it over your unit.
å
Make equal marins alon all four edes of the BACK (I). Push
on opposite corners of your unit if needed to make it “square”.
å
Fasten the BACK (I) to your unit usin the NAILS (PP).
å
NOTE: Be sure to tap NAILS into the holes that line up
over the UPRIGHTS and SHELF.
å
NOTE: Perforations have been provided for access
throuh the BACK. Carefully cut out the holes needed.
Step 12
Do not stand the unit upriht without the
BACK fastened. The unit may collapse.
Caution
NAIL
(48 used in this step)
PP
These holes must line up over the
SHELF (H) and UPRIGHTS (C and D).
I
414802 www.sauder.com/servicesPae 16
Step 13
VIEW THE T-LOCK BOX VIDEO
Groove
D720
D720
å
Fasten the DRAWER BACK (D73) to the DRAWER SIDES (D16 and D17). Use four BLACK 1-9/16" FLAT HEAD SCREWS (LL).
å
NOTE: Be sure the DRAWER BOTTOM (D720) inserts into the roove of the DRAWER BACK (D73).
å
Repeat this step for the remainin drawer.
12
3
å
Insert the DRAWER SIDES (D16 and D17) at an anle
into the slot at each end of the DRAWER FRONT (M).
å
Slide the DRAWER BOTTOM (D720) into the rooves in the
DRAWER SIDES (D16 and D17) and DRAWER FRONT (M).
The tabs should insert freely
into the slots. Gently tilt the
DRAWER SIDES side to side
until the tabs slip into the slots.
Start each screw a few turns before
completely tihtenin any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(8 used in this step)
LL
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT roove.
Unfi nished
surface
With the palm of your
hand, tap the DRAWER
BOTTOM down into
the roove.
D17
D17
D17
D73
D16
D16
D16
M
M
414802www.sauder.com/services
Pae 17
å
Insert a SLIDE CAM (FF) into the DRAWER SIDES (D16 and D17).
å
Fasten the drawer RIGHT (35GC) and DRAWER LEFT (35GD)
to the drawer sides (D16 and PD17). Use FOUR GOLD 516"
FLAT HEAD SCREWS (OO) throuh holes #1 and #3.
å
NOTE: The screw head in the cam must be visible throuh
the slotted hole in the slide.
å
Repeat this step for the other drawer.
Step 14
1
2
3
1
2
3
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
OO
Screw head - turn CAM to line up holes in
the SLIDES with holes in DRAWER SIDES
FF
FF
D16
D17
414802 www.sauder.com/servicesPae 18
å
Fasten a KNOB (EE) to the DRAWER FRONT (M). Use a
GOLD 1" MACHINE SCREW (MM).
å
Repeat this step for the other drawer.
Step 15
GOLD 1" MACHINE SCREW
(2 used for the KNOBS)
MM
M
EE
414802www.sauder.com/services
Pae 19
å
Carefully stand your unit upriht.
å
To insert a drawer into your unit, tip the front of the drawer
down and drop the rollers on the drawer behind the rollers
on the unit. Lift the front of the drawer up and slide it into
the unit.
å
Repeat this for the other drawer.
Step 16
Place the roller on the SLIDE
behind the roller on the RAIL.
414802 www.sauder.com/servicesPae 20
Side Step: Make
nachos. (Optional, but
recommended.)
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Sauder Entertainment Credenza Installation guide

Sauder
Brand
Sauder
Model
Entertainment Credenza
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents