Johnson Controls CKM-MR16OUT Hardware Installation

Brand: Johnson Controls

Model: CKM-MR16OUT

Type: Hardware Installation

This manual is also suitable for

P2000

Johnson Controls CKM-MR16OUT is a terminal module designed to provide output control for OEM system integrators. It features 16 form-C contact relays for load switching, allowing you to control various devices or systems. The module also includes 2 digital inputs for tamper and power fault status monitoring, enhancing the security of your installation. CKM-MR16OUT supports RS-485 communication, enabling seamless integration with other devices and systems. Its compact design and versatile mounting options make it suitable for various applications and environments.

24-10707-82 Revision D

December 2017

P2000

Security Management System

CKM-MR16OUT

authentic Mercury™ terminal module

hardware

installation

Johnson Controls

No part of this document may be reproduced without the prior permission of Johnson Controls.

If this document is translated from the original English version by Johnson Controls, all reasonable

endeavors will be used to ensure the accuracy of translation. Johnson Controls shall not be liable

for any translation errors contained herein or for incidental or consequential damages in connection

with the furnishing or use of this translated material.

Due to continuous development of our products, the information in this document is subject to

change without notice. Johnson Controls shall not be liable for errors contained herein or for

incidental or consequential damages in connection with furnishing or use of this material. Contents

of this publication may be preliminary and/or may be changed at any time without any obligation to

notify anyone of such revision or change, and shall not be regarded as a warranty.

Other Manufacturers’ Documentation

Johnson Controls does not duplicate documentation of other equipment manufacturers. When

necessary, Johnson Controls provides documentation that supplements that of other manufacturers.

When unpacking your equipment, keep all original manufacturer documentation for reference.

Technical Support

For factory technical support, Johnson Controls authorized field technicians or authorized dealer

representatives can contact Global Security Solutions Technical Support by phone at

(866) 893-0423 or (414) 524-1214, or by email at [email protected]

. They

can also call the Field Support Center at (800) 524-1330 or (414) 524-5000 and use options 6, 1, 7.

End users and customers should contact their local Johnson Controls branch or authorized dealer

for any of their support needs (technical support, maintenance contracts, on-site field support,

P2000 Software Service Agreements, Service Partnerships, and so on). Visit

http://www.johnsoncontrols.com/location-finder

to find your local Johnson Controls office.

For material returns contact the branch if the material was purchased through a Johnson Controls

branch or through the Product Sales Operations Team, if ordered through the Advanced Order

Management System (AOMS) and follow the RMA process; or contact the authorized dealer

representative where the material was purchased directly.

Single Point of Contact by Region

Acknowledgments

Metasys® and Johnson Controls® are trademarks of Johnson Controls. All other company and

product names are trademarks or registered trademarks of their respective owners.

European Single Point of Contact

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

NA/SA Single Point of Contact

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

APAC Single Point of Contact

JOHNSON CONTROLS

C/O CONTROLS PRODUCT

MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

Declarations of Conformity

United States: This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

Canada: CAN ICES-3 (A)/NMB-3(A)

European Union: This product complies with the requirements of the EMC Directive.

This equipment must not be modified for any reason and it must be installed as stated in the

Manufacturer’s instruction. If this shipment (or any part thereof) is supplied as second-hand

equipment, equipment for sale outside the European Economic Area or as spare parts for either a

single unit or system, it is not covered by the Directives.

UNDERWRITERS LABORATORIES COMPLIANCE VERIFICATION SHEET

The following model number is listed under Underwriters Laboratories® (UL) 1076 for Proprietary

Burglar Alarm Units and Systems, UL 294 for Access Control Systems Units and Underwriters

Laboratories of Canada ULC/ORD-C1076-86.

CKM-MR16OUT

When installed at the site the following requirements must be met to comply with these standards.

1. The CKM-MR16OUT shall be mounted in Listed Enclosures CCKM-CE75-E2M, CKM-

CE150-E4M, and Listed Burglar Alarm and Access Control System Units SPF10000-1I00,

SPF1I100-1I00 or SPF1I300-1J00.

2. A CKM-MR16OUT mounted in Listed Enclosures CKM-CE75-E2M, CKM-CE150-E4M, and

Listed Burglar Alarm and Access Control System Units SPF10000-1I00, SPF1I100-1I00 or

SPF1I300-1J00 shall be powered through the CKM-F8P power distribution module.

3. Transient protection devices that are installed must not be removed or defeated.

4. Do not connect equipment to an AC power source that is controlled by a switch.

5. Power for devices connected through relay/control output wiring must be provided by a UL

Listed power limited power source.

6. Encrypted communication has not investigated by Underwriters Laboratories.

7. Suitable for use with the model P2K-nnn-UL-x Security Management System, where n can be

any number 0 through 9 and where x can be any three letters A through Z.

8. UL 294 Performance Levels

Destructive Attack Level I

Endurance Level IV

Line Security Level I

Standby Power Level I

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

CKM-MR16OUT TERMINAL MODULE

This document provides hardware installation and setup instructions for

CKM-MR16OUT, the authentic Mercury™ terminal module. This document is

divided into the following sections:

• General Information on page 1

• Mounting Information on page 2

• Wiring Information on page 2

• Setup Information on page 5

• Status LEDs on page 7

• Specifications on page 8

• Maintenance on page 9

ENERAL INFORMATION

The CKM-MR16OUT output terminal module provides a solution to the OEM

system integrator for output control. The controller has 16 form-C contact

relays for load switching. Additionally, 2 digital inputs are provided for tamper

and power fault status monitoring. The CKM-MR16OUT requires 12 to 24

VDC for power.

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

MOUNTING INFORMATION

Figure 1: CKM-MR16OUT Hardware

WIRING INFORMATION

This sections covers the following:

• Cable Routing

• Supplying Power

• Communications Wiring

• Inputs for Cabinet Tamper/Power Fault

• Relay Outputs Wiring

6.00 [152.40]

5.50 [139.70].25 [6.35]

2.00 [50.80]3.00 [76.20]2.00 [50.80]

8.00 [203.20]

12 435 12976 8 13 1410 11 15 16

TB10

TR+

GND

R+

R-

TR-

RS-485

GND

VIN

GND

TB9

TB11

J2 J1

J1, J2

RS-485

TERM

OUT 8

OUT 7

TB4 K8

OUT 6

OUT 5

OUT 4

OUT 3

OUT 2

OUT 1

TB3K7 TB2 TB1

K11

K12

K10

K13

K14

K15

K16

TB5

TB6

TB7

TB8

OUT 9

OUT 10

OUT 11

OUT 12

OUT 13

OUT 14

OUT 16

OUT 115

POWER IN

12-24Vdc

SIO COMMUNICATION

PORT, RS-485

TAMPER AND POWER

MONIOTR INPUTS

DIP SWITCHES

STATUS LEDs

Ø.156 [Ø4.0]

8 PLACES

OUTPUTS

RELAY STATUS LEDs

.50 [12.70]

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

Cable Routing

The cables should run in grounded conduit or at least two feet from AC

power, fluorescent lights, or other high energy sources.

IMPORTANT: All data cables should be physically separated from power lines. If

conduit is used, do not run data cables in the same conduit as power cables or

certain door strike cables, e.g. strike voltage greater that 42V or Magnetic door

locks without EMI suppression.

All cables must conform with the following regulations:

• National Electrical Code

•NFPA 70

• Local electrical codes

• Canadian Electric Code C22.1 (installations in Canada)

• BSI Standard BS7671, latest edition (installations in Great Britain)

Cabling should be made using good wiring practices and should be long

enough to allow service loops at their terminations in the enclosure.

Supplying Power

The CKM-MR16OUT requires 12 to 24 VDC for power on TB11. Locate

power source as close to the unit as possible. Connect power with

minimum of 18 AWG wires.

Figure 2: CKM-MR16OUT Supplying Power

IMPORTANT: Observe polarity on VIN.

12 TO 24Vdc

GND

VIN

TB11

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

Communications Wiring

The CKM-MR16OUT communicates to a controller via a two-wire RS-

485 interface. The interface allows multidrop communication on a single

bus of up to 4,000 feet (1,200 m). Use twisted pair (minimum 24 AWG)

with shield for the communication line.

Install the following jumpers for the RS-485 interface according to the

selected configuration.

Figure 3: CKM-MR16OUT Communications Wiring

Inputs for Cabinet Tamper/Power Fault

Input CT and input BA are used for monitoring cabinet tamper and power

failure with normally closed contacts. These two inputs are for contact

closure monitoring only, and do not use EOL resistors. If you are not

using these inputs, install a short piece of wire at the input to indicate a

safe condition.

Figure 4: CKM-MR16OUT Cabinet Tamper and Power Fault Wiring

GND

CABINET

TAMPER

POWER

FAULT

TB9

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

Relay Outputs Wiring

The following diagrams show typical use of the relay. A DC power

source is recommended whenever possible. Transient clamping must be

provided to protect the contacts and to reduce EMI emission. Use

sufficiently large wires for the load current to avoid voltage loss.

Figure 5: CKM-MR16OUT Relay Outputs Wiring

SETUP INFORMATION

Table 1: Jumpers

Jumper Description

J1 RS-485 termination, install in first and last units only

J2 Factory Use Only

J3 Two-wire/four-wire select, install in 2W position only

J4 - J9 Factory Use Only

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

Table 2: Switches

S8 S7 S6 S5 S4 S3 S2 S1 Selection

OFF OFF OFF OFF OFF Address 0

OFF OFF OFF OFF ON Address 1

OFF OFF OFF ON OFF Address 2

OFF OFF OFF ON ON Address 3

OFF OFF ON OFF OFF Address 4

OFF OFF ON OFF ON Address 5

OFF OFF ON ON OFF Address 6

OFF OFF ON ON ON Address 7

OFF ON OFF OFF OFF Address 8

OFF ON OFF OFF ON Address 9

OFF ON OFF ON OFF Address 10

OFF ON OFF ON ON Address 11

OFF ON ON OFF OFF Address 12

OFF ON ON OFF ON Address 13

OFF ON ON ON OFF Address 14

OFF ON ON ON ON Address 15

ON OFF OFF OFF OFF Address 16

ON OFF OFF OFF ON Address 17

ON OFF OFF ON OFF Address 18

ON OFF OFF ON ON Address 19

ON OFF ON OFF OFF Address 20

ON OFF ON OFF ON Address 21

ON OFF ON ON OFF Address 22

ON OFF ON ON ON Address 23

ON ON OFF OFF OFF Address 24

ON ON OFF OFF ON Address 25

ON ON OFF ON OFF Address 26

ON ON OFF ON ON Address 27

ON ON ON OFF OFF Address 28

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

STATUS LEDS

ON ON ON OFF ON Address 29

ON ON ON ON OFF Address 30

ON ON ON ON ON Address 31

OFF OFF 115,200 BPS

OFF ON 9,600 BPS

ON OFF 19200 BPS

ON ON 38,400 BPS

OFF

Encrypted communication not

required

ON Encrypted communication

required

1. Firmware revisions prior to 1.38.1, this setting is 2,400 BPS.

2. Firmware revisions prior to 1.38.1, SW8 is not defined. Set to the OFF position.

Table 3: LED Information

Process LED Information

Power-up All LEDs OFF

Initialization Once you apply power, initialization of the module begins.

When initialization is completed, LEDs A, B, CT, and BA are briefly

sequenced ON then OFF.

Running A LED Heartbeat and On-Line Status:

Offline

1-second rate, 20% ON

Online

Non-encrypted communication: 1-second rate, 80% ON

Encrypted communication:

0.1 second ON

0.1 second OFF

0.1 second ON

0.1 second OFF

0.1 second ON

0.1 second OFF

0.1 second ON

0.3 second OFF

Table 2: Switches

S8 S7 S6 S5 S4 S3 S2 S1 Selection

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

SPECIFICATIONS

Use this interface in low voltage, Class 2 circuits only.

Running

(continued)

A LED Error Indication:

Waiting for application firmware to be downloaded:

1 second ON

1 second OFF

Running

(continued)

B LED SIO Communication Port Status:

Indicates communication activity on the SIO communication port.

Running

(continued)

CT: Cabinet Tamper

BA: Power Fault

Running

(continued)

LED 1 through 16: Illuminates when output relay OUT 1 (K1), OUT 2 (K2)

is energized, and so on.

Table 4: CKM-MR16OUT Specifications

Category Description

Primary Power 12 to 24 VDC ±10%, 1100 mA maximum (plus reader current)

12 VDC at 850 mA nominal

24 VDC at 450 mA nominal

Relay Contacts 16 Form-C, 5A at 30 VDC, resistive

Inputs 2 unsupervised, dedicated for cabinet tamper and UPS fault

monitoring

Communication RS-485, two-wire. 9600, 19200, 38400, or 115200 bps

Cable Requirements

Power 1 twisted pair, 18 AWG.

RS-485 24 AWG, 120 ohm impedance, twisted pair with shield, 4,000 ft

(1,219 m) maximum

Inputs 1 twisted pair, 30 ohms maximum

Outputs As required for the load.

Environmental

Temperature 32 to 120°F (0 to 49 °C) operating

-67 to 185°F (-55 to 85°C) storage

Humidity 10 to 93% RHNC

Table 3: LED Information

Process LED Information

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

MAINTENANCE

Impaired Performance

The following is a list of the impaired performance conditions:

• Unit environment not as specified

• Unit power not as specified

• Cable type and length not as specified

Test Procedure

To check for proper operation of the device:

1. Verify LED status indicates device is online.

2. Change the state of any input and verify change of state.

3. Change the state of any output and verify change of state.

Mechanical

Dimensions

(W x L x H)

6 in x 8 in x 1in (152mm x 203 mm x 25 mm)

Weight 14 oz. (400 g) nominal

Table 4: CKM-MR16OUT Specifications

Category Description

CKM-MR16OUT Hardware Installation Manual

24-10707-82 Rev. D

We welcome your comments at [email protected].

Security Solutions

(805) 522-5555

www.johnsoncontrols.com

Johnson Controls CKM-MR16OUT Hardware Installation

Brand: Johnson Controls

Model: CKM-MR16OUT

Type: Hardware Installation

This manual is also suitable for

P2000

Download PDF

report

Johnson Controls CKM-MR16OUT Hardware Installation

This manual is also suitable for

Johnson Controls CKM-MR16OUT Hardware Installation

Related papers

Other documents