Audioplex KS-2-DX4056 EYE Installation guide

Brand: Audioplex

Model: KS-2-DX4056 EYE

Type: Installation guide

KS-2-DX4056 EYE

SPECIFICATIONS

INSTALLATION

WARRANTY

Power: Supplied from K-2/S-2 package.

Connectors: Screw type connectors.

Remotes: Kenwood / Sony.

Range: 25-35 feet.

Angle: + or - 35 degrees off nominal axis.

Wire: Must be wired with two 16-2 wires.

The KS-2-DX4056 Eye works in conjunction with the K-2 / S-2 package, creating a 2-way system

designed to receive infrared signals from remote controllers via remote sensors, and send them to the base

unit, which in turn sends these signals to remote repeaters. This unit also sends a return signal back to the

remote control, confirming that the signal has been received. This system is not capable of making devices

remote controllable that are not so already, but allows remote system operation from any room in a structure

where the KS-2 Eye sensors are installed. NOTE: No more than 4 sensors should be used in a system.

The K-2 / S-2 base unit must be positioned in a location to receive the 455khz data signal from the

front of the A/V Receiver. Either in front, beside, or by using reflective material to direct the signal. If the 1/8"

jumper accesory for Kenwood is not used then the TBW emitter should likewise be positioned. If using the

Stick-Emit, the emitter should be positioned directly over the component's IR sensor. You may have to move

the emitter around to find the "sweet spot". Once a good position is found, peel the backing paper off and

adhere the emitter to the unit. Make sure that the emitter is not in the line of sight or reflection of any

sensors as radiation from the repeater may be picked up by a system sensor, resulting in a feedback situation

which causes instability and unreliable operation. Undesirable reflection can occur off light colored walls,

windows, mirrors and even shiny wood finishes. Connect the emitter to central processor and to the sensor

eyes, following the wiring diagram on the back of this sheet. The system must be wired with two 16-2 wires.

For connection, prepare the wire leads for the emitter and all remote sensors by stripping about 1/4"

of insulation from each of the wire ends. Twist strands tightly together so that none stick out to cause possible

short circuits. Insert the wire ends into the outputs on the back of the base unit following the wiring diagram

on the back of this page. Tighten all screws and inspect for loose wire strands, etc.

Plug the power supply into the wall, and the wire lead into the jack labeled POWER on the back of the

base unit. The unit is now ready to operate.

Your AUDIOPLEX TECHNOLOGY KS-2 Eye is covered by a LIFETIME warranty against any defects

in workmanship and materials. Any defects will be remedied without charge for labor or parts.

Damage incurred by shipping or by accident is not considered to be a defect, and not covered by this

warranty. AUDIOPLEX TECHNOLOGY is not responsible for defective operation caused by abuse or by

modification or service by any unauthorized person or agency.

The unit must be properly installed and operated according to instructions for the warranty to apply.

Any necessary servicing must be done by AUDIOPLEX TECHNOLOGY. The unit must be shipped with the

proof of purchase and in the original carton and packing materials to avoid damage.

This warranty gives you specific legal rights. You may have other rights which vary from state to state.

TECHNOLOGY

INSTALLATION MANUAL

2003 - 5/12/03

(Patent Pending)

K-2 or S-2 Package required for installation

GD GD

455

K-2/ S-2 BASE UNIT

12 VDC POWER SUPPLY

2-WAY A/V RECEIVER

OPTIONAL EMITTER

1/8" jumper accessory for Kenwood Receivers to "IR Receiver In".

SEE KENWOOD INTRUCTIONS!!!!

KS-2 RECEIVER EYE

( 1 INCLUDED WITH PACKAGE)

KS-2 RECEIVER EYE

(OPTIONAL)

KS-2 RECEIVER EYE

(OPTIONAL)

KS-2 RECEIVER EYE

(OPTIONAL)

EMITTER SIGNAL +

455 KHz

40 KHz

455

12V

455

12V

455

12V

455

12V

WIRING DIAGRAM

AUDIOPLEX TECHNOLOGY

404 GWH P.O. BOX 440 MELVIN VILLAGE, NH 03850

800-257-2077 603-544-8601 FAX: 603-544-8901

www.audioplex.com

2003 - 5/12/03

IMPORTANT NOTE:

Use two equal length 16/2

wires to connect the receiver

eye to the base unit as follows:

(1) one 16/2 connects the 40

kHz signal and the 12 VDC.

(2) second 16/2 connect the

455 kHZ signal and ground.

This connection method

ensures optimum operation.

Audioplex KS-2-DX4056 EYE Installation guide

Audioplex KS-2-DX4056 EYE Installation guide

Audioplex KS-2-DX4056 EYE Installation guide

Related papers

Other documents