Whirlpool WBE3322 A+NFXAQUA Program Chart

Brand: Whirlpool

Model: WBE3322 A+NFXAQUA

Category: Dishwashers

Type: Program Chart

Whirlpool WBE3322 A+NFXAQUA is a refrigerator-freezer combination that features several advanced functions to keep your food fresh and organized. Its "ECO GREEN" setting optimizes energy consumption while maintaining optimal food preservation. The built-in fan improves temperature distribution and prevents condensation. The antibacterial filter and crisper help keep your food fresh and free from bacteria. The freezer compartment provides ample space for frozen items, with dedicated zones for different types of food.

A. Refrigerator Compartment

2. Lighting

3. Shelves / Shelf area

4. Multi-flow cold air system

5. Cooler compartment

6. Rating plate with commercial name

8. Crisper divider

9. Reversibility kit

10. Separator

11. Water tank

12. Door trays

13. Balcony - eggs tray

B. Freezer Compartment

14. Storage zones for frozen food items (basket or flap)

14a. "Eco green" basket ( only in models with ECO GREN function)

15. Shelves

16. Bottom basket (freezing zone)

17. Ice tray and/or cold accumulator

19. The freezer door trays for pizza or other frozen products with a short

storage time

Depending on the model the number and type of accessories may vary.

The freezer compartment can be used without the baskets / flap and without

upper shelf to increase storage for large products.

Place the food products directly on the racks.

After inserting food, ensure that the freezer compartment door closes

properly.

C. Control panel

Anti-bacterial protection :

1. Filter in fan (depending on the model)

7. Crisper with antibacterial additives (depending on the model)

18. Door seals

The crisper and the door seals are manufactured from materials that inhibit

bacterial growth.

Notes:

- In case of power failure the cold accumulator helps to keep optimal

storage temperature longer.

- All shelves and door trays are removable.

- The internal temperatures of the appliance depend on the ambient

temperature, frequency of opening the doors, as well as location of the

appliance. Temperature setting must consider these factors.

- The appliance accessories are not suitable for washing in dishwasher.

HOW TO START THE APPLIANCE

Fit the spacers (if supplied) on the upper part of

the condenser at the rear of the appliance.

After plugging the appliance to the mains, it starts

the operation automatically.

Wait at least two hours before switching the

appliance on, to ensure that the refrigerant

circuit is fully efficient.

The indicator LEDs on the control panel light up for approximately 1 second,

and after initialization process, setpoint is displayed.

Note:

- If food is placed in the refrigarator before the appliance has cooled

completely, it may deteriorate.

- If fresh food is loaded in freezer position 3 on control panel should be

chosen.

CONTROL PANEL DESCRIPTION

1. extra low temperature

2. low temperature

3. "ECO GREEN" position (depending on the model)

4. high temperature

5. temperature selection pushbutton

6. internal light switch

FAN WITH A BUTTON

The fan improves temperature distribution inside the refrigerator compartment,

allowing better preservation of stored food.

To switch on the fan press the button (1a). It is advisable to activate the fan

when the ambient air temperature is over 27 ÷ 28°C or if you perceive drops

of water on the glass shelves or in the severe humidity conditions.

Note:

Do not obstruct the air intake area with food items.

The fan will run ONLY when the compressor is in operation.

Remember to turn off the fan when there is a lower ambient air

temperature.

If the appliance has the fan it can be equipped with the antibacterial filter.

Remove it from the box (found in the crisper drawer (item 7) and insert into the

cover of fan (item 1b).

The replacement procedure is attached with the filter.

OPERATION DESCRIPTION

Temperature adjustment is made with pushbutton (5). Temperature setpoint is

done for both compartments at one time – fridge and freezer.

At first plug-in of appliance factory setpoint is chosen – medium position (ECO

Green, depending on model).

Following table shows set-points level

Description LED OFF LED ON

GUIDE TO SELECTING FUNCTIONS

Temperature selection pushbutton is used to set desired temperature level,

from warmest through lower to coldest . Pressing pushbutton setpoint

will change cyclically.

Cooling off /Stand-by function

This function turns off the refrigerator and freezer compartments.

When the product is in this mode the light operates normally, all other loads are

disabled and control panel shows no indication. When the appliance has to be

left for a longer period with fridge door open to avoid odour, power cord has to

be unplugged from the power supply.

To put the appliance in this state press and hold temperature selection

pushbutton for 3 seconds.

Appliance comes back to normal operation, control panel displays previously

chosen set-point after press temperature selection pushbutton again.

Note:

- Remember that this operation does not disconnect the appliance from the

power supply.

- In case of power failure, appliance goes back to normal operation and

previously chosen setpoint is restored.

ECO GREEN function

This function gives best food preservation performance with the smallest energy

consumption possible (around 5-10% less in comparison with the normal

settings) if there is lower amount of food to be preserved in the appliance.

The best food preservation conditions when ECO function is activated are in

the ECO compartments:

- 2 "eco green" shelves in the fridge (with green frames)

- 1 "eco green" basket in freezer compartment.

ABNORMAL APPLIANCE OPERATION

When the product is plugged in to the mains, during first 10 minutes of its

performance, possible temperature sensor failure will be displayed according to

following table:

Description LED OFF LED Flashing

The appliance will work preserving the food stored, but it is necessary to

contact after-sales service and provide alarm code.

high temperature

low temperature

extra low temperature

Refrigerator sensor failure

Freezer sensor failure

Refrigerator freezer sensor failure

PRODUCT SHEET

DEFROSTING THE REFRIGERATOR COMPARTMENT

Refrigerator compartment defrosting is completely automatic.

Droplets of water on the rear wall inside the refrigerator compartment indicate

that the automatic defrost phase is in progress. The defrost water is

automatically run into a drain hole and collected in a container, where it

evaporates.

DEFROSTING THE FREEZER COMPARTMENT

No Frost freezers provide chilled air circulation around the storage areas and

prevent the formation of ice, thereby completely eliminating the need for

defrosting. Frozen items don't stick to the walls, labeling stays legible and

storage space remains neat and clear.

REPLACING THE LIGHT BULB

Always disconnect the refrigerator from the

power supply before replacing any light bulb.

If the inside light is not working, it is necessary

to:

1. Remove the light cover: put the fingers into the side ventilation holes (1),

stretch the cover gently and move it upwards.

2. Check the bulb. If necessary unscrew the broken bulb and replace it with

the new one (use maximum 15W bulb).

3. Put on the light cover. Do not leave the bulb uncovered.

5019 637 01071

Printed in Poland 02/10

Water tank (fig. 1)

The water tank is made of antibacterial material. This prevents and reduces the proliferation of bacteria.

An internal container, with an active carbon filtered ensures water filtration.

To fill the tank: rotate the water inlet towards you and fill with water, using a jug or other suitable container. Once the tank is full,

close the water inlet by moving it back to its original position.

Always use drinking water only: any other liquid may impair product performance.

Obtaining filtered water (fig. 2)

After filling the tank, the water may not be immediately available. This is because the filtering process may require a few minutes

(depending on the amount of water in the tank).

To dispense water: with the refrigerator door closed, press the water dispenser tab with the glass.

If for safety reason water delivery must be prevented, simply press the stop at the back of the tab. To release water delivery move

the stop back to its original position.It is recommended to drink the supplied water from the dispenser in 6 hours.

Cleaning the water tank (fig. 3-4-5-6-7-8-9)

Periodically clean the water tank with running water. Twice a year it is recommended to keep healthy the unit using specific

products based on diluted chlorine that not modify the material properties and rinse with current water.

To clean the tank, proceed as follows:

-(fig. 3) release and remove the top door tray

-(fig. 4) release and remove the water tank by lifting it and pulling towards you. Place the tank on a flat surface, remove and wash

the top cover.

Note: the tank must be refitted in its position as soon as possible, to prevent the refrigerator from overheating.

- (fig. 5a -5b) remove the internal container and the filter, and wash them separately. When washing the filter,

only use clean water (no detergent or sharp tools). To clean the disk filter, first remove it from the container.

- (fig. 6) for a more thorough cleaning, remove the valve cap (the fitting connecting the tank to the refrigerator) by

rotating it anticlockwise. Clean the cap. Important: do not pull on the valve body (fig. 7).

- (fig. 8) replace the valve cap by rotating clockwise.

- (fig. 9) fit the tank back in place by placing it between the lateral guides of the door and pushing it in position,

ensuring that the valve is back in its original seat. Check that the there are no gaps between the rubber seal of the

tank and the door.

Suggested exchange of filter for a standard consumption usage of:

3,0 l/day 4 months

4,5 l/day 3 months

6,0 l/day 2 months

Filter replacement is not covered by product warranty. To order more water filter cartridges, please contact your

after-sales service.

Stop

Activation

device

Water

drip

tray

Fig. 2

Fig. 1

Ta nk

To fill the tank, rotate the cap in

the direction of the arrow

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 7

Fig. 8

Fig. 9

UTILISATION AND MAINTENANCE OF THE WATER DISPENSER AND FILTER (if present)

Water dispenser

First use

The first time you use the water dispenser or after a long period left not used wash the tank and the filter with water.

The water dispenser provides fresh, filtered water, without the need of opening the refrigerator door. This will reduce the number of times the door is

opened, thus also reducing energy consumption of the product.

Fitting and replacing the active carbon filter

The water filter should be removed from the foil bag (found in the crisper drawer (item 7). Follow the instructions provided with the filter.

Important: If the filter is left dry for an extended period of time, its performance may be reduced. Immerse the filter in water for a few seconds to reinstate

optimum performance.

PRODUCT SHEET