Whirlpool WBE3322 A+NFX Program Chart

Category
Freezers
Type
Program Chart
A. Refrigerator Compartment
2. Lighting
3. Shelves / Shelf area
4. Multi-flow cold air system
5. Cooler compartment
6. Rating plate with commercial name
8. Crisper divider
9. Reversibility kit
10. Egg tray
11. Separator
12. Door trays
B. Freezer Compartment
13. Storage baskets for frozen food items
14. Shelves
15. Bottom basket (freezing zone)
16. Ice tray and/or cold accumulator
18. The freezer door trays for pizza or other frozen
products with a short storage time
Depending on the model the number and type of
accessories may vary.
The freezer compartment can be used without the two
upper baskets to increase storage for large products. The
lower basket
must not be removed.
Place the food products directly on the racks.
After inserting food, ensure that the freezer compartment
door closes properly.
C. Control panel
Anti-bacterial protection :
1. Filter in fan (depending on the model)
7. Crisper with antibacterial additives (depending
on the model)
17. Door seals
The crisper and the door seals are manufactured from
materials that inhibit bacterial growth.
Notes:
- In case of power failure the cold accumulator helps
to keep optimal storage temperature longer.
- All shelves and door trays are removable.
- The internal temperatures of the appliance depend
on the ambient temperature, frequency of opening the
doors, as well as location of the appliance. Temperature
setting must consider these factors.
- The appliance accessories are not suitable for
washing in dishwasher.
FAN WITH A BUTTON
The fan gives more even temperature distribution inside
the refrigerator compartment, allowing better
preservation of stored food.
To switch on the fan press the button (1a). It is advisable
to activate the fan when the ambient air temperature is
over 27 ÷ 28°C or if you perceive drops of water on the
glass shelves or in the severe humidity conditions.
Note:
Do not obstruct the air intake area with food items.
The fan will run ONLY when the compressor is in
operation.
Remember to turn off the fan when there is a lower
ambient air temperature.
If the appliance has the fan it can be equipped with the
antibacterial filter.
Remove it from the box (found in the crisper drawer
(item 7) and insert into the cover of fan (item 1b).
The replacement procedure is attached with the filter.
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts the
operation automatically. The indicator lamps on the
control panel light up for
approximately 1 second, and after initialization process,
setpoint is displayed.
Note:
if food is placed in the refrigarator before the appliance
has cooled completely, it may deteriorate.
If fresh food is loaded in freezer position 3 on control
panel should be chosen.
CONTROL PANEL DESCRIPTION
1. extra low temperature
2. low temperature
3. "ECO GREEN" position (depending on the model)
4. high temperature
5. temperature selection/stand-by (3 sec.) pushbutton
6. internal light switch
OPERATION DESCRIPTION
Temperature adjustment is made with pushbutton (5).
Temperature setpoint is done for both compartments at
one time – fridge and freezer.
At first plug-in of appliance factory setpoint is chosen –
medium position (ECO Green, depending on model).
PRODUCT SHEET
GB
ROBGRUSHSKCZPLIGB FINDKNSGRPENLFD
Following table shows set-points level
Description Lamp OFF Lamp ON
GUIDE TO SELECTING FUNCTIONS
Temperature selection / stand-by pushbutton is used
to set desired temperature level, from warmest
through lower to coldest . Pressing pushbutton
setpoint will change cyclically.
Stand-by / ON function
To put the appliance in Stand-by state press and hold
Temperature selection / stand-by pushbutton for 3
seconds.
All loads are disabled, indicators switch off.
To switch on the product when it is in Stand-by state,
press Temperature selection / stand-by pushbutton
for 3 seconds.
Appliance comes back to normal operation, control panel
displays previously chosen setpoint.
Note: in case of power failure, appliance goes back to
normal operation and previously chosen setpoint is
restored.
ABNORMAL APPLIANCE OPERATION
When the product is plugged in to the mains, during first
10 minutes of its performance, possible temperature
sensor failure will be displayed according to following
table:
Description Lamp OFF Lamp Flashing
The appliance will work preserving the food stored, but it
is necessary to contact after-sales service and provide
alarm code.
DEFROSTING THE FREEZER
COMPARTMENT
Whirlpool No Frost freezers provide chilled air
circulation around the storage areas and prevent the
formation of ice,
thereby completely eliminating the need for defrosting.
Frozen items don't stick to the walls, labeling stays legible
and storage
space remains neat and clear.
DEFROSTING THE REFRIGERATOR
COMPARTMENT
Refrigerator compartment defrosting is completely
automatic.
Droplets of water on the rear wall inside the refrigerator
compartment indicate that the automatic defrost phase is
in progress. The defrost water is automatically run into a
drain hole and collected in a container, where it
evaporates.
REPLACING THE LIGHT BULB
Always disconnect the
refrigerator from the power
supply before replacing any
light bulb.
If the inside light is not
working, it is necessary to:
1. Remove the light cover: put the fingers into the side
ventilation holes (1), stretch the cover gently and move it
upwards.
2. Check the bulb. If necessary unscrew the broken bulb
and replace it with the new one (use maximum 15W
bulb).
3. Put on the light cover.
Do not leave the bulb uncovered.
PRODUCT SHEET
GB
5019 637 01054
Printed in Poland 03/09
ROBGRUSHSKCZPLFINDKNSGRIPENLFGBD
Refrigerator sensor failure
Freezer sensor failure
Refrigerator freezer sensor failure
high temperature
low temperature
extra low temperature
  • Page 1 1
  • Page 2 2

Whirlpool WBE3322 A+NFX Program Chart

Category
Freezers
Type
Program Chart

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI