Barco LD140-8 Installation guide

LD display

Installation & service manual

R5976773/04

27/04/2006

Barco nv Media

Noordl

aan 5, B-8520 Kuurne

Phone: +32 56.36.89.70

Fax: +32 56.36.83.86

E-mail:

[email protected]

Visit us at the web: www.barco.com

PrintedinBelgium

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-

ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the

program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this

publication; these changes are incorporated in new editions of this publication.

stored in a retrieval system without the prior written consent of Barco.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On rece

ipt, the purchaser

must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco

must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,

at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement

at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a

reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or

indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component

of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties

guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goo

ds delivered by Barco, or if the goods are handled incorrectly,

in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not

agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are

system failures which are attributed to programs or special electroni

c circuitry provided by the purchaser, e.g. interfaces. Normal wear as

well as normal maintenance are not subject to the guarantee provided by Barco either.

The environmental conditions as well as the servicing and maintenance regulations specified in the this manual must be complied with by

the customer.

Trademarks

Brand and product names mentioned in this manual may be trade

marks, registered trademarks or copyrights of their respective holders.

All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for

the products or their manufactures.

Table of contents

TABLE OF CONTENTS

1. Safety................................................................................................................. 3

1.1 Safety guidelines ..................................................................................................................... 4

1.2 Important safety instructions ......................................................................................................... 5

1.3 Important warnings ................................................................................................................... 6

1.4 Specific important warnings for the D2 digitizer..................................................................................... 7

2. Installation requirements ......................................................................................... 9

2.1 Installation requirements for the LD display . .. .....................................................................................10

2.2 Installation requirements for the D2 digitizer . ...................................................................................... 11

2.3 System requirements for the Control software .....................................................................................12

3. System overview ..................................................................................................13

3.1 LD display tiles....................................................................................................................... 15

3.2 LD supporting structure ............................................................................................................. 17

3.3 LD mounting accessories ...........................................................................................................18

3.4 D2 digitizer...........................................................................................................................20

3.5 Mono phase power box . . ...........................................................................................................23

3.6 LD software..........................................................................................................................24

3.7 LD filter kit (optional) ................................................................................................................ 25

4. Set up process of a LD display .................................................................................27

4.1 Set up process of a freestanding LD display ....................................................................................... 28

4.2 Set up process of a wall mounted LD display . .....................................................................................29

4.3 Set up process of a hanging LD display ............................................................................................ 30

5. Installation procedures...........................................................................................31

5.1 Installation of the LD feet............................................................................................................32

5.2 Installation of the support frame upon the LD feet .................................................................................34

5.3 Installation of the wall mount adapter. . . ............................................................................................ 37

5.4 Installation of the support frame upon the wall mount adapter . . ..................................................................39

5.5 Installation of the support frame hanging on the ceiling. . . . . . ......................................................................42

5.6 Installation of the precision frames upon the LD support structure................................................................ 45

5.6.1 Installation of the height adjustment brackets ............................................................................... 46

5.6.2 Installation of the first precision frame........................................................................................47

5.6.3 Installation of the second precision frame.................................................................................... 49

5.6.4 Installation of the third and following precision frames ......................................................................52

5.7 Installation of the mono phase power box . . . . . .....................................................................................54

5.7.1 Physical installation of the mono phase power box.......................................................................... 55

5.7.2 Electrical installation of the mono phase power box. . . ......................................................................56

5.8 Installation of the US mono phase power box . ..................................................................................... 58

5.8.1 Physical installation of the US mono phase power box . . . ..................................................................59

5.8.2 Electrical installation of the US mono phase power box. . . .................................................................. 60

5.8.3 Adaptation of the side cladding for the US mono phase power box ........................................................ 61

5.9 Installation of the D2 digitizer ....................................................................................................... 63

5.10 Data cabling of the D2 digitizer .....................................................................................................65

5.11 Installation of all the LD tiles ........................................................................................................67

5.11.1 Installation of all the LD tiles with back access to the display...............................................................68

5.11.2 Installation of all the LD tiles without back access to the display. . . . . .......................................................69

5.12 Z-alignment of the LD tiles .......................................................................................................... 71

5.13 Installation of the filter kit............................................................................................................73

5.14 Installation of the top- , bottom- and side-cladding support brackets ..............................................................75

5.15 Installation of the top and bottom cladding .. . . ..................................................................................... 77

5.16 Installation of the left and right side cladding . . ..................................................................................... 80

5.17 Installation of the rear cladding . .................................................................................................... 82

5.18 Installation of the single foot cladding...............................................................................................84

6. Cabling diagrams of the LD display............................................................................87

6.1 Power cabling diagram of the LD display...........................................................................................88

6.2 Data cabling diagram of the LD display.............................................................................................89

7. Maintenance........................................................................................................91

7.1 Cleaning the LD display . . ...........................................................................................................92

7.2 Cleaning or replacing the LD filters ................................................................................................. 93

7.3 Cleaning the dust filter of the D2 digitizer. . . . . . .....................................................................................95

8. Troubleshooting ...................................................................................................97

8.1 No image on the LD display.........................................................................................................98

8.2 No image on part of LD display .....................................................................................................99

8.3 Dark and bright LED’s on the LD display ..........................................................................................100

8.4 Fan fail of a LD tile..................................................................................................................101

9. Servicing.......................................................................................................... 103

9.1 Safety instructions..................................................................................................................104

R5976773 LD DISPLAY 27/04/2006

1

Table of contents

9.2 Locate and access the tile fixation nuts, power socket and data ports ...........................................................105

9.3 Access to the power box and D2 digitizer .........................................................................................107

9.4 Replacing a D2 input module . . . ...................................................................................................108

9.5 Replace a LD tile with back access to the display.................................................................................109

9.6 Replace a LD tile without back access to the display .............................................................................111

9.7 Replace the resync-unit of a LD tile................................................................................................112

9.8 Replace the SMPS unit of a LD tile................................................................................................113

9.9 Replacing the fan of a LD tile ......................................................................................................115

9.10 Replacing a dust filter unit of the LD display.......................................................................................117

A. Specifications ..................................................................................................... 119

A.1 Specifications LD 120 - 8 model ...................................................................................................120

A.2 Specifications LD 140 - 8 model ...................................................................................................121

A.3 Specifications LD 140 - 10 model..................................................................................................122

A.4 Specifications LD 150 - 8 model ...................................................................................................123

A.5 Specifications LD 150 - 10 model..................................................................................................124

B. Order info .......................................................................................................... 125

B.1 Spare part order info ...............................................................................................................126

Index.................................................................................................................... 127

2 R5976773 LD DISPLAY 27/04/2006

1. Safety

1. SAFETY

Overview

• Safety guidelines

• Important safety instructions

• Important warnings

• Specific important warnings for the D2 digitizer

R5976773 LD DISPLAY 27/04/2006

3

1. Safety

1.1 Safety guidelines

Personal protection

WARNING: Ensure you understand and follow all the safety guidelines, safety instructions, warnings and

cautions mentioned in this manual.

WARNING: Be aware of suspended loads.

WARNING: Wear a hard hat to reduce the risk of personal injury.

WARNING: Be careful while working with heavy loads.

WARNING: Mind your fingers while working with heavy loads.

Installation personnel

This installation must be performed by authorized and qualified technical personnel only.

Accredited safety officers must ensure the safety of the site, construction, assembly, connection, use, dismantling, transport etc. of

such safety critical systems.

Caution

Installation should be performed only after you are thoroughly familiar with all of the proper safety checks and installation instructions.

To do otherwise increases the risk of hazards and injury to the user.

Assembly parts are designed for intended use only in conjunction with Barco LD displays.

Do not modify and/or replicate any component. Barco uses specific

materials and manufacturing processes in order to achieve part

strength. Consult Barco for assistance with custom applications.

Always follow Barco installation instructions. Contact Barco if you should have any question regarding the safety of an application.

The manufacturer assumes no liability for incorrect, inadequate, irresponsible or unsafe assembly of systems.

Product care

Structural & mounting components should be kept dry, clean, lubricated (only if recommended), coated properly, and otherwise

maintained in a manner consistent with part design. Barco products must be used in a manner consistent with their design and

inspected on a routine basis for security, wear, deformation, corrosion and any other circumstances that may affect the load handling

capability of the part.

Barco recommends inspections at regular interval

s for all installations and increasing in frequency for more critical installations. If

a part is found to have damage, which may cause a decrease in load capability, the part must be removed for service or replaced

immediately.

Under no circumstances are Barco parts repairable by anyone other than Barco.

4

R5976773 LD DISPLAY 27/04/2006

1. Safety

1.2 Important safety instructions

Instructions:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer

for further advice should any doubts exist regarding any cleaning procedure.

• Do not block ventilation openings. Install in accordance with the manufacturers instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that

produce heat.

• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs are damaged

then replacement of the defective parts must be undertaken immediately.

• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus. Replace damaged power/data cords immediately.

• Only use attachments/accessories specified by the manufacturer.

• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning protection. Unplug this

apparatus when unused for long period of time.

• Refer all servicing to qualified service technicians/personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, the apparatus does not operate normally, or has been dropped.

• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use ca

ution during lifting/moving

or transporting to avoid damage by possible tipping.

R5976773 LD DISPLAY 27/04/2006

5

1. Safety

1.3 Important warnings

Important Warnings:

• Risk of electric shock:

Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer

servicing to qualified service personnel.

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

CAUTION

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk

of electrical shock to persons.

The exclamation point within a triangle is intended to tell the user that important oper

ating and/or servicing instructions are

included in the technical documentation for this equipment.

• Maximum ambient temperature:

Consult the “LD temperature control” table below to determine the maximum ambient temperature for your LD display.

LD temperature control

Ambient temperature < 30 °C.

- Filter kit required in dusty environments.

30 °C < Ambient temperature < 40 °C

- Filter kit always required.

- Monitoring of the tile temperature required.

o

The value for “Min. contrast” must be set on 100 Nit.

o

The value for “Max. temperature” must be set on 60 °C.

(These values can be set in the LD configuration software → tab page

“Monitoring” → Set up button of “Temperature control”)

• Minimum ambient temper

ature:

The minimum ambient temperature for the LD display is 0 °C.

• High leakage current:

The combination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid risk of electric

shock due to high leakage current, proper grounding of the installation is required.

• Flammable materials:

Keep flammable materials aw

ay from the installation (such as curtains). A lot of energy is transferred into heat. The installation

should be such that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation

must be provided.

• ESD and LED’s:

LED components used in LD devices are ESD (Electro-Static Discharge) sensitive. To prevent the possibility of destroying LED

components do not touch either in operation or while switched off.

• Risk of electric shock / Ri

sk of fire: To protect against risk of fire by overloading of power cables, MAXIMUM 7 TILES may

be connected in parallel. Each power source cable supplying MAXIMUM 7 TILES should be protected by a circuit breaker or

fuses rated 16 A / 250 VAC (15 A / 250 VAC in the USA and Canada).

• Disconnect device:

When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed near

the equipment and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed

wiring.

• This equipment MUST be earthed:

In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the

grounding type plug w

ill expose you to the risk of electric shock.

• Power system:

It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding

conductor) in order to avoid large ground current loops due to voltage differences in the neutral conductor. The total electrical

installation should be protected by an appropriately rated disconnect switch, circuit breakers and Ground Fault Current Inter-

rupters. The installation shall be done according to the local electrical installation codes. In Europe special attention should be

given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should be adhered to.

• Mains cords:

The power cords delivered with this system have special properties for safety. They are not user serviceable. If the power cords

are damaged, repla

ce only with new ones. Never try to repair a power cord.

6

R5976773 LD DISPLAY 27/04/2006

1. Safety

1.4 Specific important warnings for the D2 digitizer

Warnings

• Maximum ambient temperature:

The maximum ambient temperature for this equipment is 40 °C.

• This equipment MUST be earthed:

In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the

grounding type plug will expose you to the risk of electric shock. This apparatus must be grounded (earthed) via the supplied

3 conductor AC power cord. (If the supplied power cord is not the correct variant, consult your dealer.)

• Use of an extension cord:

If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the

extension cord does not exceed the extension cord ampere rating. Also make sure that the total of all products plugged into

the wall outlet does not exceed 15 amperes.

• Cabinet openings:

Never push objects of any kind into this product through cabinet slots as they may touch dangerous high voltage points or short

out parts that could result in a risk of fire or electrical shock.

Never spill liquid of any kind on the product. Should any liquid or solid object fall into the cabinet, unplug the set and have it

checked by qualified service personnel before resuming operations.

R5976773 LD DISPLAY 27/04/2006

7

1. Safety

8 R5976773 LD DISPLAY 27/04/2006

2. Installation requirements

2. INSTALLATION REQUIREMENTS

Overview

• Installation requirements for the LD display

• Installation requirements for the D2 digitizer

• System requirements for the Control software

R5976773 LD DISPLAY 27/04/2006

9

2. Installation requirements

2.1 Installation requirements for the LD display

Size

The LD display is delivered in several packages containing separate parts. Each individual part can pass through a standard door

opening to gain easy access to the installation area. It’s obvious that the dimensions of the destination area must cover the physical

dimensions of the LD display. See specification of the chosen LD model for exact dimensions.

Weight

The weight of one separated part, without packaging, of the LD display does not exceed 50 kg. This limitation allows that the set

up of the LD display can be done by two persons. But, do not underestimate the weight of a complete LD display. Be sure that the

surface (floor, wall or ceiling) on which the display has to be installed is capable of handling five (5) times the com

plete load of the

LD display. See specification of the chosen LD model to know the complete weight of the display.

Ambient temperature

Maximum ambient temperature:

Consult the “LD temperature control” table below to determine the maximum ambient temperature for your LD display.

LD temperature control

Ambient temperature < 30 °C.

• Filter kit required in dusty environments.

30 °C < Ambient temperature < 40 °C

• Filter kit always required.

• Monitoring of the tile temperature required.

- The value for “Min. contrast” must be set on 100 Nit.

- The value for “Max. temperature” must be set on 60 °C.

(These values can be set in the LD configuration software → tab page “Monitoring”

→ Set up button of “Temperature control”)

Minimum ambient temperature:

The minimum ambient temperature for the LD display is 0 °C.

Humidity

The LD display is designed for indoor use. The humidity level at the operating area must be between 35 and 85%. To forsake this

requirement will result in damage of internal parts of the LD display.

Ventilation

A lot of energy is trans

ferred into heat. The installation should be such that the amount of air flow required for safe operation of the

equipment is not compromised. Proper ventilation must be provided. The location of the air in- and outlet for the fans will be different

depending on the kind of installation (floor, wall or ceiling). The LD display must be installed in such a manner that the air in- and

outlets are comple

tely free.

Power

A mono phase power net must be provided at the installation place for the LD display. The allowed range of the power voltage is

from 190 to 230 volt. Use one power source cable with a section of 10 mm

2

protected with a 63 ampere switch fuse.

Data path

The data path between the D2 digitizer and the LD display may not exceed five (5) meter.

Accessibility

It’s not recommended to install the LD display on a location where the audience are able to touch the display. On the other hand the

installation location must easy be accessible for maintenance purposes like cleaning the air filters.

10

R5976773 LD DISPLAY 27/04/2006

2. Installation requirements

2.2 Installation requirements for the D2 digitizer

Requirements

• The D2 digitizer should not be placed in a built-in installation or enclosure unless proper ventilation is provided.

• When using the unit in a multi unit rack assembly or closed assembly, the ambient temperature inside the assembly may not

exceed the maximum rated ambient temperature of the digitizer. The installation should be such that the amount of air flow

required for safe operation of the equipment is not compromised.

• When building in the D2 digitizer into a rack with cover door, be aware that a space of minimum 85 mm is needed between the

indicated reference and the cover door. This space is needed to guide the input cables to the inputs.

85 mm

• The D2 digitizer will require that air flows freely in vent holes. Blocking these holes will greatly reduce the reliability of the unit

and lead to the possibility of overheating.

• The D2 Digitizer should operate from an AC power source. The D2 digitizer is equipped with an auto-ranging power supply

from 85 to 264 volt (50–60 Hertz).

• When installed in a rack, the mounting should be such that no hazardous condition is achieved due to uneven mechanical

loading.

• When the mains switch located on the back of the D2 digitizer is not accessible due to rack mounting, the socket outlet supplying

the rack shall be installed near the equipment and be easily acces

sible or a readily accessible disconnect device shall be

incorporated in the fixed wiring. When using a rack in an installation it is advisable to log the serial number of the device and to

activate the warranty figure by registering utilizing the included form.

• Do not place the D2 digitizer on an unstable cart, stand or table. The device may fall, causing personal injury and serious

damage to the digitizer.

• The data path between the D2 digitizer and the LD display may not exceed five (5) meter.

R5976773 LD DISPLAY 27/04/2006

11

2. Installation requirements

2.3 System requirements for the Control software

Before you begin

Is assumed you are familiar with the Windows operating system at your site.

The CD-ROM in your package contains a Windows-based installation program. You can install the software from the CD-ROM.

System requirements

Minimum specifications :

• Hardware

- PC Pentium III or equivalent, 1 GHz

-512MbRAM

- Free hard disk space: 300 Mb

- XGA resolution (1024 x 768)

- Serial communication port

• Software

- Windows 2000, Windows XP Home or Windows XP Professional

Recommended specifications :

• Hardware

- PC Pentium IV or equivalent, 2.4 GHz

-512MbRAM

- 300 Mb hard disk free space

- SXGA resolution (1280 x 1024) with 32 Mb video memory

- Serial communication port

• Software

- Windows XP Professional

12

R5976773 LD DISPLAY 27/04/2006

3. System overview

3. SYSTEM OVERVIEW

Introduction

The LD is a fixed size indoor LED display solution that comes in two resolutions (8 mm and 10 mm) and in three models (120,

140 & 150). Each LD display contains a D2 digitizer for image processing and a CD-ROM with the LD software for configuring and

controlling the complete system.

There are three mounting configurations for the LD display. Freestanding, ceiling mount and wall mount. Depending on the chosen

mounting configuration additional mounting accessories are required. These additional accessories are offered b

y Barco as mount-

ing kits.

Image 3-1

Available LD models:

Article No. Name Description

R9052590 LD 120-8 Full color 127” LED display with 8 millimeter resolution.

R9052630 LD 140-8 Full color 142” LED display with 8 millimeter resolution.

R9052640 LD 140-10 Full color 142” LED display with 10 millimeter resolution.

R9052680 LD 150-8 Full color 152” LED display with 8 millimeter resolution.

R9052690 LD 150-10 Full color 152” LED display with 10 millimeter resolution.

Available mounting kits:

Article No. Name

Content

R985260

0

LD 120 - W

all mount kit

Support brackets for a wall mount configuration.

Side cladding for the LD 120.

R9852610 LD 120 - Freestanding mount kit

Foot with fixation accessories.

Side claddi

ng for the LD 120.

Rear cladding for the LD 120.

R9852620

LD 120 - Ceiling mount kit Suspension system.

Side cladding for the LD 120.

Rear cladding for the LD 120.

R9852650 LD 140 - Wall mount kit

Support brackets for a wall mount configuration.

Side cladding for the LD 140.

R9852660 LD 140 - Freestanding mount kit

Foot with fixation accessories.

Side cladding for the LD 140.

Rear cladding f

or the LD 140.

R5976773 LD DISPLAY 27/04/2006 13

3. System overview

Article No. Name

Content

R9852670

LD 140 - Ceiling mount kit Suspension system.

Side cladding for the LD 140.

Rear cladding for the LD 140.

R9852700 LD 150 - Wall mount kit

Support brackets for a wall mount configuration.

Side cladding for the LD 150.

R9852710 LD 150 - Freestanding mount kit

Foot with fixation accessories.

Side cladding for the LD 150.

Rear cladding for the LD 150.

R9852720

LD 150 - Ceiling mount kit Suspension system.

Side cladding for the LD 150.

Rear cladding for the LD 150.

Optional kits

Article No. Name

R9853210

Filter kit for LD 140/150

• Seven filter units.

• Adapted bottom cladding plates.

R9853220

Filter kit for LD 120

• Six filter units.

• Adapted bottom cladding plates.

R9850960

DVI input module for digitizer

R9850970

SDI input module for digitizer

R9850980

HDSDI input module for digitizer

R9850920

CVBS / S-VID input module for digitizer

R9850940

YUV / RG(s)B input module for digitizer

R9851710

RGB analog input module for digitizer

R9850930

Dummy input module for digitizer

The following chapters enumerates all different components of a LD display and describe their functionality

in the display system.

Overview

• LD display tiles

•LDs

upporting structure

• LD mounting accessories

• D2 digitizer

• Mono phase power box

• LD software

• LD filter kit (optional)

14

R5976773 LD DISPLAY 27/04/2006

3. System overview

3.1 LD display tiles

Functionality

The display of the LD is built up with display tiles. All tiles are connected in series via a data path. The physical location of a tile in the

data path does not matter because within the LD model all tiles are equal. But the data path must be created in a daisy chain matter.

Each tile picks out a part of the video information of the data stream on the data path and process this information for displaying on

its LED’s.

Depending of the chosen LD model the resolution of the display tile can be different, either 8 millimeter or 10 millimeter. The LD tiles

need to be powered up via the mono phase power box which supplies a voltage between 190 and 230 volt.

Image 3-2

LD display tile (8 millimeter: R9052700 ; 10 millimeter: R9052710).

Re-sync unit

Every tile contains a re-sync unit (A) which can easily be removed. The re-sync unit synchronizes the incoming data stream and

sends it to the next tile. The data ports (B) on the re-sync unit are bidirectional. So, it doesn’t matter on which port the data is coming

in, the re-sync unit switch the functionality of the data ports spontaneously between input and output. Furthermore the re-sync unit

is equipped with status LED’s (C) for diagnostic purposes.

A

B

C

Image 3-3

A Re-sync unit (R9851520); B Data ports; C Status LED’s.

Cabling

The display tile is provided with power via a power split cable with a C13 plug. Data cabling between tiles is done with a DVI-DVI

data cable of 0,9 meter.

R5976773 LD DISPLAY 27/04/2006

15

3. System overview

A

Image 3-4

A : Power input (C14 socket).

Image 3-5

Power split cable (R9851130).

Image 3-6

DVI-DVI data cable of 0,9 meter (R9851211).

16 R5976773 LD DISPLAY 27/04/2006

Page is loading ...

Barco LD140-8, LD120-8, LD140-10, LD150-10, LD150-8 Installation guide

Related papers

Other documents