Sunricher SR-2300TS-RGB-US-DT6 User manual

Brand: Sunricher

Model: SR-2300TS-RGB-US-DT6

Type: User manual

DALI RGB Touch Controller 09.230TSR6.04066

Function introduction

Important: Read All Instructions Prior to Installation

Back side

Wiring diagram

Product Data

012

(x10)

(x1)

V- D1V+ D2

DC INPU T DALI OU TPU T

43.58 mm

65.58 mm

Back side

DC Power input DALI signal output

DALI Wall Panel

Controller

83.00 mm

19.4 mm

Output Signal DALI signal

Power Supply 12-24VDC

Power consumption 200 mA

Operating temperature 0-40°C

Relative humidity 8% to 80%

Dimensions 75x120x29.1mm

DALI Master/

DALI Master software

via computer

12-24VDC

PSU

AC 100-240V

012

(x10)

(x1)

V- D 1V+ D2

DC IN PUT DAL I OUTPU T

DALI Wal l Panel

Controlle r

Front side

123

GND

AC Power

50/60Hz

V+

V-

OUTPUT

INPU T

12V/24V/36V

CV PSU

Connect with RGB LED S tr ip

V+ V+

R- R-

G- G-

B- B-

Connect with RGB LED S tr ip

V+ V+

R- R-

G- G-

B- B-

123

GND

RGB color slider

ON/OFF button

4 light zones, click to

select, press and hold

down to turn ON/OFF

Scene button, press and

hold down to save a

scene, click to recall

Play/Pause button, click

to play/pause running

effects, press and hold

down to speed up/down

RGB brightness button,

press and hold down to

increase/decrease light

intensity

1*(0~9) for setting

units position

10*(0~9) for setting

tens position

Rotary switches for setting start

DALI address number (0-63),

the number equals to tens position

plus units position

• DO NOT install with power applied to device.

• DO NOT expose the device to moisture.

Safety & Warnings

• Touch sensitive.

• Glass interface(white & black).

• Comply to DALI standard protocol IEC 62386-102, IEC

62386-207 and in compliance with DALI products from

other international incorporation.

• 4 light zones are available for switch, dimming and RGB

color control, each zone can control 3 DALI addresses.

• Enable to set start DALI address number (0-63) for the 4

zones by rotary switches on the back.

• Enable to save 1 scene for each light zone

• Built-in 8 Color Sequences

Installation

Operation

Set start DALI address number for the zones by rotary switches on the back:

Set the number as X (0-63):

Zone number Z1 will control DALI addresses X, X+1 and X+2,

Zone number Z2 will control DALI addresses X+3, X+4 and X+5,

Zone number Z3 will control DALI addresses X+6, X+7 and X+8,

Zone number Z4 will control DALI addresses X+9, X+10 and X+11,

Note: if X is set as 63, zone 1 will control DALI address 63, 00 and 01, zone 2 will control address 02, 03 and 04,

zone 3 will control address 05, 06 and 07, zone 4 will control address 08, 09 and 10.

Sunricher SR-2300TS-RGB-US-DT6 User manual

Sunricher SR-2300TS-RGB-US-DT6 User manual

Sunricher SR-2300TS-RGB-US-DT6 User manual

Related papers

Other documents