NSTRUCTIONS
I
AmeriScale™
Model AMERI 3
ML-28984
FORM 33836 (4/97)
AMERISCALE
★
701 RIDGE AVENUE
TROY, OHIO 45374-0001
– 2 –
© HOBART CORPORATION, 1997
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part
15 of FCC Rules. These limits are designed to provide reasonable protection against interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions manual, may cause
interference to radio communications. Operation of this equipment in a residential area is likely to cause
interference in which case the user will be required to correct the interference at his own expense.
To meet Class A limits, the user must observe the following requirements:
1. Only factory approved cables may be used to connect this digital device with any peripherals.
2. Only factory approved peripherals may be connected to this digital device.
3. Any changes or modifications to the equipment, unless expressly approved by the manufacturer, could
void the FCC's permission to operate the equipment.
Verification of weight should be done routinely by placing a known weight on the platter and checking the
displayed weight. If the scale does not function as described in this manual, contact your local Hobart Service
Office for re-calibration, service, or repair.
– 3 –
TABLE OF CONTENTS
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
USER GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ELECTRICAL CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
LEVELING THE SCALE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DISCONNECTION AND POWER-UP. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
KEYPAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
KEYPAD ENTRIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ACCUMULATOR LIMITS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Illuminated Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
MISCELLANEOUS PLU MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PRICING TYPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
By Weight (U.S.) ( 1 lb, or 1 – 9 lb for ) . . . . . . . . . . . . . . . . . . . . . . 8
By Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PLU EDIT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PLU LOOKUP MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Special Tare Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Portion Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Platter Tare Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
PREPACK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
ACCUMULATOR FUNCTIONS, TOTALS . . . . . . . . . . . . . . . . . . . . . . . 12
METRIC DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
METRIC PRICING TYPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
By Weight (Metric) ( 1 kg, or 100 grams ) . . . . . . . . . . . . . . . . . . . . . 14
By Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
– 4 –
PL-40169-1
Platter
Adaptor
Security Plate
Display
Keypad
Level
AmeriScale
Installation, Operation, and Care of
AmeriScale™
SAVE THESE INSTRUCTIONS
GENERAL
The Hobart AmeriScale is a durable, compact weighing device. Two digital displays show the weight,
unit price, and total price to the seller and buyer at the same time. The scale can calculate the value
of either weighed or by count items and can accumulate the total price for multiple items.
The maximum capacity is 30 pounds. The maximum metric capacity is 15 kg. The maximum capacity
includes any Tare weight subtracted for packaging. The increment or division size is available as
shown in the table.
Avoirdupois (US Pounds)* Metric (Kilograms)*
Total
Weight - 0-30 lb. 0-10 lb. 10-30 lb. 0-15 kg 0-6 kg 6-15 kg
Range
Increment
or Division .01 lb. .005 lb. .01 lb. .005 kg .002 kg .005 kg
Size
* For U.S. Pounds, when scale weight reaches 10 lb. the .01 lb. increment is used until the scale returns to zero. For Metric
Kilograms, when scale weight reaches 6 kg. the .005 kg increment is used until the scale returns to zero.
USER GUIDELINES
Do NOT jar the weighing platter or drop objects on it.
Do NOT press keys hard; a light touch is sufficient.
Avoid locations with vibration; avoid direct sunlight.
Do NOT splash water on the scale.
WARNING: UNPLUG BEFORE CLEANING.
Clean the cover and weighing platter by wiping with
a dry or lightly moistened cloth. The stainless steel
platter can be removed (by lifting straight up) and
washed in a sink with mild detergent and warm
water. Do NOT use solvent or abrasive materials for
cleaning. Replace the platter after it is clean and dry.
★
– 5 –
INSTALLATION
Immediately after unpacking, check for possible shipping damage. If this unit is found to be damaged,
save the packaging material and contact the carrier within 15 days of delivery.
The Security Plate is available and can be used by Weights and Measures after calibration to seal the
scale if they use a lead-wire type seal.
ELECTRICAL CONNECTION
Connect the wall-mount adapter plug to a 120 V, 60 Hz, 1 ph electrical outlet. The adapter converts
to 12 Volts
DC,
.8 Amp, required for the scale to operate. Alternatively, a Vehicle Adapter with 20 foot
cord is available and allows connection to the cigarette lighter on any car or truck having a 12 Volt
DC
electrical system. With either voltage source, connect the small round 12 Volt
DC
connector to the
mating terminal on the left side of the scale.
LEVELING THE SCALE
Level the scale by turning the feet in or out until the bubble indicator is centered. A Locking Nut,
provided on the threaded shaft of each foot, allows the level adjustment to be locked-in.
DISCONNECTION AND POWER-UP
If the scale is disconnected, the accumulator total and any displayed values will be lost. When powerup
occurs, the scale will resume in MISCELLANEOUS PLU MODE. Disconnection and powerup will always
retain the programmed values of the 30 PLUs saved during a previous PLU EDIT MODE.
– 6 –
OPERATION
KEYPAD
Enter numeric values for PLU, By Count, Tare, lb/for, and Price.
Look-up or edit pricing values for any PLU numbered 1 – 30.
For By Count Pricing, set how many pieces (1 – 99) are being sold for the price.
For By Weight pricing, enter the tare value to be subtracted from the weight.
Enter the price (up to 999.99).
Add the total price to the Accumulated Total. Net Weight must be greater than twice the
increment or division size. [Initial versions of AmeriScale will not accommodate
connection of a peripheral printer. Future upgrades/options may permit an optional
peripheral printer, which, if connected, would print the total price of the item.]
Clear various values depending on when it is pressed.
For Multiple Pounds pricing, set how many pounds (1– 9) are being sold for the price.
[ If configured for metric weighing and enabled, the item is priced for 100 grams instead
of 1 kg.]
Prepack/Date locks-in current pricing and allows several items with the same price to be
weighed and priced. Totals can be accumulated. Prepack can only be activated when
a unit price is displayed. Press Clear
CE
to exit Prepack and return pricing values to zero.
Set the scale to zero weight.
Display the Accumulated Total (Packages and Total Price)*. [Initial versions of
AmeriScale will not accommodate connection of a peripheral printer. Future upgrades/
options may permit an optional peripheral printer, which, if connected, would print the
Accumulated Total.]
[ Press Print/Total A SECOND TIME to return to pricing values without clearing the total.]
KEYPAD ENTRIES
•Whenever a valid keypad entry is made, a single beep will sound.
•Invalid entries will be signaled by a single beep followed by a series of rapid beeps.
* ACCUMULATOR LIMITS
The accumulator, ( ) , can add up to 60,000 packages. The price total can run up to 9999.99 or
999.99 (with 5 digit total price display) depending on the configuration.
100g
lb/for
CE
9
0
PLU
50
10
1
Pcs
T
– 7 –
DISPLAY
WEIGHT/COUNT
Displays Total Weight, Net Weight, Tare, or By Count Quantity, as indicated.
UNIT PRICE $
Numeric entries are displayed here prior to being identified as Tare, Price, By Count, or lb For.
The programmed Unit Price may be per: pound, 1 to 9 pounds, count, kg, or 100g, as indicated.
TOTAL PRICE $
Displays the total price of this transaction or the Accumulator Total, as indicated.
An illuminated "∇" displayed above the term indicates . . .
TARE
The tare is displayed in the weight field.
ZERO
The scale's platter weight is stable at 0.00 in .01 lb. or 0.000 in .005 lb.
NET
The tare is subtracted from the total weight.
lb The weight is in U.S. pounds.
kg The weight is in Kilograms.**
lb
FOR
The
Pounds For
quantity (the number of pounds sold for the Unit Price) is displayed. The
lb for
feature can only be used if Price is less than $ 100.00.
PREPACK
The unit price remains the same for all items in the group.
100g
FOR
The Unit Price is for 100 grams.**
PROG
In PLU EDIT MODE: Edit the pricing values for PLU's.
ACCUM
The Accumulated Total is more than $ 0.00.
TOTAL
The Total Price is the Accumulated Total.
* If configured for metric weighing, the scale's platter weight is stable at 0.000 kg.
** Metric weighing is not available when configured for U.S. pounds. Also, 100 g pricing
may be disabled on metric scales.
– 8 –
Pricing values can be entered in one of three modes: 1) In Miscellaneous PLU Mode where, once
entered, pricing codes are cleared when totaled. 2) As a change to the programmed pricing values
during PLU Edit Mode. 3) As a temporary override to a PLU during PLU Lookup Mode.
NOTE: The following Mode information is written from the Operator Display perspective. Fields and
information on the elevated display (optional) will appear different.
MISCELLANEOUS PLU MODE
Following power-up and rezero, the scale enters
Miscellaneous PLU Mode, indicated by the display —
all pricing values equal 0.00.
Manually enter the pricing values for an item by entering a numeric value followed by its identifier:
Price, Tare, By Count, or lb For — until the required pricing is displayed. Accumulator (Totals), Tare,
and Prepack functions are available to add individual total prices, display or edit the Tare, or repeat item
pricing for multiple items. Platter Tare Function (page 10) can be used if no Tare or By Count has been
entered.
PRICING TYPES
An example of each U.S. pricing type follows:
By Weight ~ ( lb ) ~ priced for 1 pound (example: Tare = .05 lb; Unit price = 1.99/lb).
5
T
1
9
9
50
10
1
By Weight ~ ( lb for ) ~ priced for 1 to 9 pounds (example: Tare = 0.15 lb; Unit price = 5 lb for 3.99).
1
5
T
5
100g
lb/for
3
9
9
50
10
1
By Count ~ ( Pcs ) ~ priced for the number of pieces (example: By Count = 4; Unit price = 1.00).
4
Pcs
1
0
0
50
10
1
*
Subsequent override of the By Count value will multiply or divide
to yield the Total Price. Example:
1
Pcs
= .25.
* NOTE: ENTER ONLY THE ABOVE SEQUENCE.
1
0
0
50
10
1
4
Pcs
YIELDS A TOTAL PRICE OF 4.00.
– 9 –
Programming Worksheet
Tare lb For Pcs Unit Price PLU Number
PL 1
PL 2
PL 3
PL 4
PL 5
PL 6
PL 7
PL 8
PL 9
PL 10
PL 11
PL 12
PL 13
PL 14
PL 15
PL 16
PL 17
PL 18
PL 19
PL 20
PL 21
PL 22
PL 23
PL 24
PL 25
PL 26
PL 27
PL 28
PL 29
PL 30
PLU EDIT MODE
Enter a PLU number (1 – 30 ) and press the
PLU
key
TWICE to enter PLU Edit Mode. PLU # 1, shown in the
display, was entered as follows:
1
PLU
PLU
.
Initially all prices are set at 0.00 for each PLU. The
∇
light above
PROG
indicates you can re-program
the pricing values for this PLU.
• To program a PLU, enter a numeric value followed by its identifier: Price, Tare, By Count, or lb For
— until the required pricing is displayed.*
• As an example, to program a tare of 0.15 lb and unit
price of 2.99 per lb, enter as follows:
1
5
T
2
9
9
50
10
1
.
• Press the
PLU
key A THIRD TIME to save the displayed
pricing values for the PLU and go to PLU Lookup Mode.
* Clear
CE
— reverts to the previous programmed values and exits to PLU Lookup Mode.
NOTE: To convert a By Count PLU to By Weight, enter
0
Pcs
.
– 10 –
PLU LOOKUP MODE
Enter a PLU number ( 1– 30 ) and press
PLU
ONCE — to
look up and display the programmed pricing for this
PLU. You can weigh items, obtain the total price of the
item, and optionally use the Accumulator (Totals),
Tare*, and/or Prepack functions.
Price information can be temporarily overridden (if not in Prepack) by entering a new numeric value,
followed by its identifier: Price, Tare, By Count, or lb For. The
CE
key will clear the temporary override
and revert back to the programmed pricing for the PLU. If no override is present,
CE
key will return
to MISCELLANEOUS PLU MODE.
Refer to PRICING TYPES, page 8, for By Weight and By Count pricing examples.
* Special Tare Function — allows view and edit of the current Tare value
If no numeric keys were pressed immediately before pressing the
T
key, the tare will display and can
be overridden; to return to the pricing display, press the
T
key A SECOND TIME. To revise a non-zero
tare with weight on the platter: Press
T
, enter the new tare, and press
T
again.
Portion Control Function — use special PLU 99 and repeat Tare for each added ingredient
PLU 99 allows you to add ingredients and Tare the weight back to zero repeatedly to control the weight
of each added ingredient type. This is handy for pizza preparation or other uses. No pricing applies.
➀ Access special PLU number 99 by entering:
9
9
PLU
.
➁ Put the item on the scale platter.
➂ Press
T
to make the weight read 0.00.
√ Add the ingredient until the desired portion displays as the weight ( X.XX lb).
➄ Repeat steps ➂ and √ for each ingredient type.
≈ When done, remove the item from the platter and press
CE
once to begin another portion control
item at step ➁. Or, press
CE
twice to return to MISCELLANEOUS PLU MODE.
NOTE: Special PLU 98 functions the same as PLU 99 but uses a 16.00 Unit Price to calculate each
added ingredient weight in ounces ( XX.XX oz ) in the Total Price display.
Platter Tare Function — PLUs with Tare value = 0.00
Any PLU that has 0.00 for the Tare value can have the Platter Tare entered — once only. NOTE: Platter
Tare Function is available in MISCELLANEOUS PLU MODE and PLU LOOKUP MODE but not in PREPACK.
➀ Access any PLU that has a Tare value equal to 0.00.
➁ Put packaging material on the scale's platter.
➂ Press
T
. NET WEIGHT displays 0.00.
√ Place the product with packaging material on the platter.
➄ Values for NET WEIGHT, UNIT PRICE, and TOTAL PRICE are displayed.
– 11 –
PREPACK
This provides a method of processing several items with the same price without needing to reenter the
price every time. Prepack can only be activated after a Unit Price has been entered or called up; View
it in the center display. Once Prepack is activated (by pressing ), the current pricing values are
locked-in until cleared to allow several items with the same price to be weighed and priced. Totals are
automatically added to the Accumulator.
You can use Prepack from Miscellaneous Product Mode or PLU Lookup Mode.
Press Clear
CE
to exit Prepack and return pricing values to zero.
Example:
• To enter a Tare, weigh the packaging material and press
T
.
— The weight should read 0.00 with the packaging material still on the platter.
• Enter the Unit Price by pressing the number keys followed by
50
10
1
.
— The Unit Price should be displayed.
• Press to activate Prepack.
— The Prepack indicator is illuminated " ∇"; Price values are locked.
As each package is weighed, its Net Weight and Total Price will be displayed.
Remove the package from the platter to return the original Tare and Unit Price values.
The Package Price is automatically added to the Accumulator as each and every
package is weighed.
When all packages have been weighed (and totaled), you are ready to leave Prepack:
• Press
CE
with nothing on the platter to return to Miscellaneous PLU Mode.
• To view / print the Accumulator Totals, press .
— Total Packages and Total Price are displayed.
• To clear the Accumulator Totals, press
CE
.
– 12 –
ACCUMULATOR FUNCTIONS, TOTALS
Add the total price of Item 1 and Item 2; display the Total and clear the Total.
Item 1: Weigh empty package for tare; Unit Price = 1.99/lb; weigh item in package (1 pound).
Item 2: By Count = 4; Unit Price = 1.00; override to 6 pieces.
Begin at Miscellaneous PLU or Clear:
CE
.
Zero the scale: .
Weigh the empty package and press
T
.
Enter the 1.99/lb unit price:
1
9
9
50
10
1
.
Place the first package on the scale.
Total Price = 1.95.
Add the total to the Accumulator: .
Tare and Unit Price return to zero*. ACCUM is lit.
Remove the package from the scale and the weight
returns to zero.
Call up a PLU priced 4 pieces for 1.00 or enter:
4
Pcs
1
0
0
50
10
1
.
Override the By Count quantity to 6 pieces:
6
Pcs
. The Price goes to 1.50.
Add the total to the Accumulator: .
Count and Unit Price return to zero*.
View the Accumulated Total: .
Clear the Total:
CE
. ACCUM is not lit.
* If PREPACK was turned on, , the previous pricing values return after the total is accumulated.
To return to zero pricing values, clear:
CE
.
During a run, you cannot void a single transaction. The entire run, Accum Total, must be cleared:
CE
.
– 13 –
METRIC DISPLAY
WEIGHT / COUNT UNIT PRICE $ TOTAL PRICE $
WEIGHT/COUNT
Displays Total Weight, Net Weight, Tare, or By Count Quantity, as indicated.
UNIT PRICE $
Numeric entries are displayed here prior to being identified as Tare, Price, By Count, or 100g
For. The programmed Unit Price may be per: kg, 100g, or count, as indicated.
TOTAL PRICE $
Displays the total price of this transaction or the Accumulator Total, as indicated.
An illuminated "∇" displayed above the term indicates . . .
TARE
The tare is displayed in the weight field.*
ZERO
The scale's platter weight is stable at 0.00 in .005 kg or 0.000 in .002 kg.
NET
The tare is subtracted from the total weight.
2g The weight is in Kilograms and division size is .002 kg.*
5g The weight is in Kilograms and division size is .005 kg.*
lb
FOR
Not applicable on metric scales.
PREPACK
The unit price remains the same for all items in the group.
100g
FOR
The Unit Price is for 100 grams.**
PROG
In PLU EDIT MODE: Edit the pricing values for PLU's.
ACCUM
The Accumulated Total is more than $ 0.00.
TOTAL
The Total Price is the Accumulated Total.
* In metric weighing, the Tare must be divisible by the metric weight increment.
** On metric scales, 100 g pricing may be disabled.
– 14 –
METRIC PRICING TYPES
Metric pricing (per kg and 100g) is configurable by your local Hobart service office. Use of the scale
as a metric weigher disables U.S. pounds pricing capability. Pricing per 100g can be disabled so all
weighed items are priced per kilogram. By Count pricing works the same with either pound or metric
weight configuration. In metric weighing, the Tare must be divisible by the metric weight increment.
The maximum allowable Tare is 9.995 kg.
By Weight (Metric) ~ priced for 1 kilogram (example: Tare = 0.020 kg; Unit price = 3.99/kg).
2
0
T
3
9
9
50
10
1
By Weight (Metric) ~ priced for 100 grams (example: Tare = 0.030 kg; Unit price = 1.99/100g).
3
0
T
100g
lb/for
1
9
9
50
10
1
Or, to save a keystroke, enter:
3
0
T
1
9
9
100g
lb/for
By Count ~ ( Pcs ) ~ priced for the number of pieces (example: By Count = 4; Unit price = 1.00).
4
Pcs
1
0
0
50
10
1
ENTER ONLY THE ABOVE SEQUENCE.
1
0
0
50
10
1
4
Pcs
YIELDS A TOTAL PRICE OF 4.00.
– 15 –
TROUBLESHOOTING
No display at power-up. Verify that the adapter plug is properly connected to the electrical outlet and
that the cord terminal is connected at the scale. Check the line circuit
breaker or fuse.
Weight not displayed. At power-up, the scale must be within 6 lb of the zero point at last calibration.
Verify that the platter is in place, no load is on the platter, and complete the
power-up cycle. If the problem is not resolved, re-calibration is indicated —
contact service.
Rezeroing the scale. After power-up, the scale will rezero up to .6 lb. If the zero point changed by
more than .6 lb, the scale can still operate by completing a power-up cycle
with the platter in place and no load on it. If the problem persists,
re-calibration is indicated — contact service.
Activating the weigher. If there is a weight displayed but the scale is not weighing, the tare is being
displayed. Press
T
or
CE
to return to regular weighing operations.
Weighing inconsistency. Make sure the scale is level and that nothing is touching the sides or bottom
of the platter.
Key entering. If a numeric key entry is followed by a series of rapid beeps, the scale is set
for Prepack. Press
CE
until the
PREPACK
indicator light is off.
Entering a lbs/for quantity. The unit price must be less than $100. Scale must be set for U.S. pounds.
Entering a unit price over A By Weight item cannot be programmed to allow a Unit Price over $99.99
$ 99.99. and also have multiple pounds pricing with
lbs/For
greater than 1. However,
a By Count item can be priced over $ 99.99.
Override of a non-zero Tare. If weight is on the platter, press
T
, enter the new tare, and press
T
again.
Accumulating items. – Verify that the weight on the platter is stable and Net Wt ≥ 20 x division.
– Only items that have a total price can be accumulated.
– If the accumulator item limit (60,000 items) is exceeded or if the total value
is more than 9999.99, clear the accumulator before continuing.
Clearing the accumulator. The accumulator can only be cleared when it is shown on the display. Press
to display the accumulator total and then press
CE
to clear the total.
Displaying a PLU. After a PLU number is entered, if the display shows zeroes, the PLU has not
been programmed. To enter PLU Edit Mode and program this PLU, enter the
PLU number and press
PLU
TWICE. The PROG light is on. Enter the
appropriate values.
Accessing By Count PLUs. To access a By Count PLU, make sure there is no weight on the platter.
To change a By Count PLU to In PLU Edit Mode, press
0
and then press
Pcs
. Enter the other required
By Weight. By Weight values as described previously.
SERVICE
If the scale does not function as described, or TROUBLESHOOTING does not resolve the problem,
contact your local Hobart Service Office for re-calibration, service, or repair.
– 16 –
REPLACEMENT PARTS
PL-52685
WEIGHT/COUNT
CAPACITY
TARE ZERO NET lb k g
lb
FOR
PREPACK
100g FOR
PROG ACCUM TOTAL
PLU/EDIT BY COUNT TARE PRICE PRINT/ACCUM
CLEAR lb 100 g PREPACK REZERO PRINT/TOTAL
30 X .01 lb
UNIT PRICE $
TOTAL PRICE $
1
6
23
7
45
890
T
50
10
Pcs
100g
lb/for
PLU
CE
1
2
56-7-8
3
9
10
11
12
13
14
17
18
19
20
25-24
26
22
21
15
16
4
23
SCALE
ILLUS. PART
PL-52685 NO. NAME OF PART AMT.
1 00-043110 Platter ...........................................................................................................................................1
2 00-043108 Cover ............................................................................................................................................ 1
3 00-046865 Screen-Operator Display (English, LB/KG) ..................................................................................1
4 00-043166 Spacer - Conductive.....................................................................................................................1
5 00-043120 Cover - Printer Card .....................................................................................................................1
6 00-043164 Standoff - Grounding ....................................................................................................................4
7 SC-018-77 Mach. Screw 6-32 x 5⁄16 Phil Pan Hd.............................................................................................8
8 WL-008-01 Lockwasher 6 Internal Shakeproof ...............................................................................................8
9 00-043182 Base .............................................................................................................................................1
10 00-043117 Keypad (English) ..........................................................................................................................1
11 00-043111 Support - Keypad .........................................................................................................................1
12 00-043147 Retainer ........................................................................................................................................ 2
13 00-043112 Level ............................................................................................................................................. 1
14 00-046448 Control Board Assy. .....................................................................................................................1
15 00-042426 Loadcell ........................................................................................................................................ 1
16 00-043116 Support - PCB ..............................................................................................................................2
17 00-043170 Power Jack Assy. .........................................................................................................................1
18 00-046458 Power Supply (115 VAC) .............................................................................................................1
19 00-043125 Foot .............................................................................................................................................. 4
20 NS-017-03 Jam Nut 1⁄4-20 Hex........................................................................................................................4
21 SC-089-02 Cap Screw 1⁄4-20 x 3⁄4 Socket Fil. Hd. ............................................................................................4
22 00-043103 Plate - Platter Support ..................................................................................................................1
23 00-043102 Support - Platter ...........................................................................................................................3
24 SC-118-20 Cap Screw 1⁄4-20 x 1⁄2 Hex Hd. ......................................................................................................4
25 WL-003-38 Lockwasher 1⁄4 Medium................................................................................................................. 4
26 00-047321 Screen-Customer Display (English, LB/KG).................................................................................1
00-047358 Kit-Elevated Display Assy. ...........................................................................................................1
00-182307 Kit-Platter Rail ..............................................................................................................................1
00-043206 Kit-Fish Pan..................................................................................................................................1
00-047099 Cover-5 Pack (Ameri Scale).........................................................................................................1
00-043100 Security Plate ...............................................................................................................................1
00-043149 Cord-Power (120VDC)(20') ..........................................................................................................1
00-044149 Extractor-Surface Mount I.C.........................................................................................................1
– 17 –
FORM 33836 (4/97) PRINTED IN U.S.A.
DISPLAY UNIT
ILLUS. PART
PL-52684 NO. NAME OF PART AMT.
1 00-046431 Housing-Display...........................................................................................................................1
2 00-046426 Screen-Display.............................................................................................................................1
3 00-046855 Screen-Display (Operator)...........................................................................................................1
4 00-046450 Board Assy.-Numeric Display......................................................................................................1
5 SC-022-07 Mach. Screw 8-32 x 1⁄2 Flat Hd. ................................................................................................... 2
6 SD-017-06 Self-Tapping Screw 6-20 x 1⁄2 Binding Hd., Type AB ..................................................................4
7 00-047357 Support-Display Post ...................................................................................................................1
8 SC-113-29 Cap Screw 1⁄4-20 x 7⁄8 Socket Hd. ................................................................................................1
9 00-046615 Cable-Display...............................................................................................................................1
10 00-047333 Bar-Draw Down............................................................................................................................ 1
11 SC-115-35 Mach. Screw 8-32 x 1⁄2 Flat Hd. ................................................................................................... 2
12 SC-018-24 Mach. Screw 6-32 x 3⁄4 Phil. Pan Hd............................................................................................1
13 SD-038-16 Self-Tapping Screw 6-32 x 3⁄8 Hex Washer Hd., Type RL ..........................................................1
14 00-259232 Post - Display (8") ........................................................................................................................1
15 00-259454 Insulator - Post.............................................................................................................................1
00-464811 Cover-Cable .................................................................................................................................1
00-046819 Label-U.L. .................................................................................................................................... 1
00-047358 Kit-Elevated Display Assy............................................................................................................1
12-13-14
9
10-11
15 6
7
4
3
2
1
5
8
PL-52684
REPLACEMENT PARTS
/
