Page is loading ...
Application Assistance
The wire le s s network may co n t ain a variety of wire le s s
d ev i ces. Instructions for installation, binding opera t i o n s ,
and use are included with the re l evant wire l e s s dev i ce s .
A p p l i c ation support information and installation guides fo r
Watt Sto p p e r / L e g r and wire l e s s network dev i ces are
a va i l a b le at www. w a t t s to p p e r. com. Comple t e the physica l
i n stallation and binding of all other wire l e ss dev i ces in the
n e t wor k befo re co n figuring the to u c h s c reen.
Scene Binding
Bind other wire le s s dev i c es in the system to appro p r i a te
g r oups and rooms befo re you attempt to exe c u t e sce n e s
f r om the MRDS10. Use an appro p r i a t e scene co n t r o l le r ,
s c ene re m o te or a MR232 and a PC running a te r m i n a l
e m u l a tor to setup and re c o rd scenes. Once re co r ded, the
MRDS10 can be included in groups and sce n e s .
C r eating new scenes using the MRDS10 To u c h s c r een is
b eyond the scope of this guide. Once you are familiar with
the basic operations described in this guide, you can use
the help screens to learn how to cre a te new sce n e s .
MIRO TOUCHSCREEN SETUP INSTRUCTIONS
B e f o re pro c eeding please read the fo l low i n g :
• All screen setups must be initiated from the
H O M E PAGE using the to o l b ox icon.
• To setup your screen fo l low the instructions give n
h e r e along with the prompts that are given on the
to u c h s c reen.
• Remember to use the help scre e n s .
• U n l e ss sta ted otherwise, these instructions ass u m e
that the Miro system is co n fig u red befo r e setting up
the to u c h s c r een.
DESCRIPTION
The MRDS10 To u c h s c re e n is a combination room and house
level scene co n t ro l l er with the capacity to also co n t r ol up to
30 individual dev i ce groups. The menus and co n t rol functions
a re acce s sed by touching the labels and icons that appear on
the scre e n .
The to u c h s c reen has a help system built into
each page. To acce ss help for a particular page,
p re s s the question mark button at the top of
the page.
Setup Screen
A to o l b ox icon appears on the HOME PAGE. Use
the to o l b ox icon to acce ss the setup scre e n s .
Status LED Indicator & Wake-up Button
The MRDS10 also uses a multi-co lor LED (gre e n / a m b e r / r e d )
to indica te dev i ce status. Dire c t l y below the LED there is a
s i n g l e push-button. Momenta r i ly pre ss this button to wake
up the to u c h s c reen when in power save mode.
The LED can display one of three co lo rs: green, ye l low
(amber, a combination of red and green), or red. The co lo r
can be co n s tant, or can flash at one of three ra t es to
d i s tinguish re p o r ted conditions. To determine the flash ra t e ,
count the number of flashes in 5 seco n d s :
5 fla s h e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Hz
10 fla s h e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hz
15 fla s h e s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hz
MRDS10 LED Indications are as fo l low s :
C o l o r B e h a v i o r M e a n i n g
n o n e O f f D e v i c e is not powe red or is in “sle e p ”
m o d e .
G r e e n On, not fla s h i n g D e v i c e is powe red, has a house ID,
o p e rating normally.
G r e e n Flashing @ 2 Hz During binding, dev i c e is excluded, but
can be added.
A m b e r On, not fla s h i n g D e v i c e does not have a house ID.
A m b e r Flashing @ 2 Hz D e v i c e is part of a binding pro c e s s, either
G r oup or Room. Binding was sta r ted by
some other dev i c e and must be sto p p e d
on the other dev i ce .
A m b e r Flashing @ 3 Hz D e v i c e is the master of a binding pro c e ss .
Binding was sta r ted on this dev i c e and
m u s t stop on this dev i c e .
R e d Flashing @ 2 Hz D e v i c e has enco u n te r ed an erro r. An
i n v alid command was atte m p te d .
Caution: Battery Vo l tage is Low ~ 10s
every 1-2 minute s
R e d Flashing 3 Hz Shutting down To u c h s c reen due to low
b a t t ery co n d i t i o n
M R D S 1 0
W i re l e ss To u c h s c reen Contro l l e r
SET HOUSE ID IN THE TOUCHSCREEN
All wire le s s dev i ces insta l l ed in the same system must acquire the
same unique House ID befo re use.
1 . M a ke sure all dev i c es are insta l led and energized and all gro u p ,
house, and room bindings are co m p le te. Make sure that eve r y
other wire l e ss dev i ce LED is green and the MRDS10 status LED is
ye l low (amber).
2 . P re s s on any p rev i o u s ly bound d e v i c e until its LED fla s h e s
amber (about 2 seco n d s ) .
3 . Verify that the LED on the MRDS10 starts flashing green. This
co n firm s that House ID m a t ches the other dev i ces in the house.
4 . Return to the same prev i o u s ly bound d ev i c e used in step 2 and
p re s s until its LED changes to solid green (about 2 seco n d s ) .
All dev i ce LEDs including the MRDS10 should now be solid gre e n .
BIND GROUPS
A group can be one dev i c e, or seve ral dev i ces anywhere in the house
that are bound together and co n t r o l led in unison. That is, for ex a m p l e ,
if you dim any dev i c e in the group, all dev i ces in the group will dim
s i m u l t a n e o u s ly. A dev i c e can only be bound to one group identity.
When you bind a group (co n taining one dev i c e, or many dev i c es) to a
g roup label on the to u c h s c reen, you can co n t r ol the group from the
to u c h s c reen.
1. D e t ermine which dev i c es you want to co n t rol from the scre e n .
M a ke sure that you know which dev i c es are already bound to each
other as a group. This will help you decide on a name for the
g roup, to be ente red as a label on the scre e n .
2 . Go to the first group and put one of the dev i ces into learn mode
( p re s s on the dev i ce until its LED starts blinking). All dev i c e s
that are curre n t l y included in this group blink amber.
3 . The screen displays a message “External Group Binding in
P ro g r e ss ...”. Read the message then pre ss OK. Notice the co l o r
of the scre e n ’s blinking LED. If it is green, it can be included in the
g roup. If it is amber, it is already included in the group where yo u
i n i t i a t ed the learn mode.
4 . When the GROUP SETUP 1-5 page appears, pre ss the ve r t i cal bar
a b o ve the GROUP number that you want to pro g ram (typica l l y yo u
would start with Group 1).
5. The screen changes to the INDIVIDUAL GROUP SETUP page.
P re s s the Edit Label icon to give the group a meaningful label.
6. The screen changes to the EDIT LABEL SETUP page. Use the
key b o a rd to enter the group name label and pre s s SAVE.
7 . P re s s (+/-) to pro c eed (LED will continue to flash gre e n ) .
8 . The screen displays a message “Group Binding A
I n c l u d e / E x clude.” Read the message then pre ss the
+
b u t ton to
include the to u c h s c reen in the current group. The screen LED
flashes amber to indica t e it is included in the gro u p .
9. C lose binding from the dev i c e where you sta r ted in step 2. Te s t
the group operation from the scre e n .
Repeat the above pro c e d u re for up to 30 succe ss i ve groups and their
a s s o c i a t ed labels.
Label Names – Eight chara c t e rs can display on a single line with a
limit of two lines. To display co m p le t e wo rds of eight chara c t e rs
or le s s per line, include a space between the wo rds, ie. :
“LIVINGRO” displays if “LIVINGROOM” is typed in the label box .
“LIVING ROOM” displays if a space is inserted between “LIVING”
and “ROOM”.
2
1
GROUP SETUP 1-5
INDIVIDUAL GROUP
SETUP Edit Label
EDIT LABEL SETUP
Group Binding “Proceed”
2.4
2.5
2.6
2.3
Group Binding A
Include/Exclude
2.8
INDIVIDUAL GROUP
SETUP Include/Exclude
2.7
page 2
ROOM SETUP
A to u c h s c reen can only be bound to one room.
1. Choose an ex i s ting room co n t ro l l er that you want to ass o c i a te
with the to u c h s c r een. Put the room co n t ro l l er into the le a r n
mode (pre ss on the dev i c e until its LED starts blinking).
2. S c reen LED flashes green and the External Room Binding In
P ro c e s s screen appears. Pre s s OK to pro c eed.
3. P re s s
+
to include the to u c h s c reen in the room. The
to u c h s c reen LED starts flashing ye l low (amber).
4. C lose the binding from the room co n t ro l l er where you sta r te d
the binding (step 1).
5. The screen returns to the HOME PAGE. If you have alre a d y
c re a ted scenes from the ex i sting room co n t ro l l er, you ca n
n o w re c all them from the to u c h s c r een.
Label the Scenes
6 . To edit the to u c h s c reen labels for the scenes, pre ss the setup
i con. This ta kes you to SETUP MENU PAGE 1. Pre s s the
Room Setup ico n .
7 . The screen changes to ROOM SCENES 1-5 SETUP. Pre ss
room scene button 1.
8 . P re s s Edit Label.
9 . The screen changes to the EDIT LABEL SETUP page (similar
to Figure 2.6). Use the key b o a r d to enter the scene label and
p re s s SAVE.
10. To adva n ce to the next scene, pre ss the a r row on the
INDIVIDUAL ROOM SCENE SETUP page. You can label up to
15 room sce n e s .
N o te s :
• To cre a te new scenes, select the light levels that you want to
re call and then pre ss and hold the Reca l l / R e c o rd icon until
the LED flashes green and the screen beeps (approx i m a t e ly 2
s e c onds).
• You can also initiate the room setup pro c e s s dire c t ly from the
to u c h s c reen by using the instructions above along with the
p rompts and the help screens.
HOUSE SETUP
If you have already cre a ted house scenes, they are auto m a t i ca l l y
included in the to u c h s c reen when you assign a house ID.
T h e re fo re, all you need to do is to label the scenes using the Edit
Label function in the INDIVIDUAL H O U S E S C E N E SETUP MENU.
You can also cre a te scenes dire c t ly from the to u c h s c reen as
fo l low s :
1 . E n ter SETUP M E N U PAGE 1.
2 . P re s s the House Setup icon.
3. P re s s the desired house scene label.
4 . Rename the house scene by pre ssing the Edit Label icon and
then labeling the scene as described in step 3.9 above .
4
3
External Room Binding in
Process Pop-up
External Room Binding A
Include/Exclude
SETUP MENU PAGE 1
ROOM SCENES 1-5 SETUP
INDIVIDUAL ROOM SCENE
SETUP
3.2
3.3
3.6
3.7
3.8
page 3
2800 De La Cruz Bouleva rd, Santa Clara, CA 95050
Te c h n i cal Support: 800.879.8585 • 972.578.1699
w w w. w a t t s to p p e r. c om
07216r1 4/2005
TROUBLESHOOTING
During Set House ID, the LED is not flashing on some Wire l e s s
d ev i ce s .
• If LED is solid green befo r e initiating house ID binding:
The dev i c e already has another house ID. Reset it to the
fa c tory default so that it can be bound to the desired house
ID. Resetting to fa c t ory defaults is described in the “I need to
start over” iss u e .
• If LED is solid amber after initiating house ID binding:
The dev i c e may be out of range of the initiating dev i c e. It may
be nece ssary to add a MRR2 Repeater if re c eption to a
particular area of the house is blo c k e d .
I need to start ove r.
You can reset any wire l e s s dev i c e EXCEPT the MRDS10 to
fa c tory default settings by pre ssing and holding until the
LED changes to solid amber (approx i m a te l y 10 seco n d s ) .
During the pro ce s s, the LED flashes amber and when
co m p le t e, it changes to solid amber. The dev i ce can then be
re co n fi g u red, ex a c t l y like any new dev i c e .
I need to set the MRDS10 To u c h s c r een to Fa c tory Defa u l t s
This will erase all binding, scene and labeling info r m a t i o n
f r om the to u c h s c re e n .
1. From the Home Page, pre ss the setup icon .
2. P r e ss Lock/Reset Setup icon .
3. Touch the box next to Reset Display.
4. Touch the YES box next to RESET TO FACTORY DEFA U LT
S E T T I N G S .
5. The to u c h s c r een will reset to Fa c tory Default Settings and
you may pro ceed with “SET HOUSE ID.”
See the instructions on the MRDS10 Setup screen for more
i n f o r m a t i o n .
Record a New House Scene
1 . To re c o rd a new scene you must first select which dev i c e s
you want bound to the scene (re f er to the instruction manual
or the instructions that came with your house level co n t ro l l e r
for an explanation).
2 . To start a binding from the scre e n :
a . P re s s the scene button that you want and pre ss the bind
i co n .
b . P l a c e the dev i c es you want to include in the scene in the
learn mode (Dev i ce LED Flashing Amber).
c . C lose the binding from the screen by pre ssing OK.
d . To re c o rd scene lighting levels, set pre fe r r ed light leve l s
and then pre s s and hold the re c a l l / re c o rd button ico n
until the LED flashes green and the screen beeps
( a p p rox i m a t e ly 2 seco n d s ) .
N o te s :
At the house level, all dev i ces are bound by default to scene five
and All House Off. Any dev i c e that you want included in other
s c enes (i.e., 2 through 10 and House On), must be bound to the
s c ene befo r e they can be co n t ro l l ed by the scene.
HOME PAGE SETUP
By default your Home Page is set to display house scenes 1 to 3
on the top row and room scenes 1 to 3 on the second row. Fo l low
the instructions on the HOME PAGE BUTTON SETUP to change
h o w your Home Page appears.
DEFAULT PAGE SETUP
You have a choice of having the Default Page (the page that
a p p e a r s after two minutes of inactivity) of being any of the
fo l lowing: a) Home Page, b) House Scenes, c) Room Scenes, or
d ) G roups. Fo l l ow the instructions on the screen.
SYSTEM LOCK
To lock your system from the screen fo l low the instructions on the
Lock/Reset Setup button. If you fo rget your pass wo rd ente r
“9999” to enter the SETUP MENU and reset your pass wo r d .
ADDITIONAL FUNCTIONS
For additional functions go to the second page of the SETUP
s c reen by scrolling fo r w a rd f rom SETUP MENU PAGE 1.
On the second setup page you will see the options fo r :
• Pa s s wo rd Setup
• Power Save Setup
• Time Setup
• C o n t ra s t/Backlight Setup
7
6
5
/
