Noble House 53865 Operating instructions

Brand: Noble House

Model: 53865

Type: Operating instructions

This manual is also suitable for

1 OF 6

Assembly Instructions

END TABLE

CAUTION: You must read this before you proceed.

CAUTION : This End Table is NOT a TOY.

Keep your child / children at bay in the process of assembly.

For turning the End Table and to prevent damage to the End Table, 02

persons may be needed to execute this action.

No.

Picture Description

Qty

Table Top

2 OF 6

Before Beginning Assembly:

Assembly Preparation

Read instructions, cover to cover.

Have 2 adults on hand for assembly.

Do not assemble on flooring or carpet.

Assemble on a clean non-marring surface (packing foam).

Save all packaging until finished.

Parts List

Legs

No.

Picture Description

Qty

Bolts

M6 x 65mm

Flat Washers M6

Allen Key

Hardware

Table Hardware

3 OF 6

Assembly Steps

OVERVIEW

Table Top (A)

Legs (B)

FRONT FACING

This End Table has multiple parts and may require up to 30 minutes to assemble. To give you an

overview of the End Table parts, the above picture is to help you put the various parts into

perspective. Please read through the instructions herebelow to familiarise the parts and steps

before assembly.

Step 1

Unpack and place all parts on a clean, non-marring surface.

Legs (B)

Assembly Steps

Place the Table top (A) with its underside skywards onto a clean, soft surface to avoid any

scratch or damage to the product.

Affix loosely the Legs (B) into the mounting position at the corners of the Table Top (A), using

the Bolts (①) with Flat Washers (②), with the Allen Key(③), as shown in the picture.

Repeat the same process with the other Legs (B).

Do not fully tigthen Bolts.

Step 2

4 OF 6

Assembly Steps

Step 3

30CM ~ 50CM

If wobble

Test again

Turn the End Table right side up

Place the End Table on a LEVEL SURFACE to see if it wobbles.

If it wobbles, lift the End Table to some 30cm to 50cm height from the ground.

Keep your feet and toes well away from the drop zone.

Drop the End Table freely and vertically with the four legs, hitting the ground, at the same time.

This Drop Test will help to ensure that all the Bolts and gaps to all reach full alignment status.

Test again for evenness on a LEVEL SURFACE.

If no wobbles found, proceed to tighten all the bolts.

CAUTION: When tightening these screws, tighten sequentially.

DO NOT tighten any screw fully and then towards the next one.

This would cause the frame to warp.

If there is still wobbles, loosen the screws and execute this same drop tests.

WARNING ! IF END TABLE IS NOT STABLE , IT COULD LEAD TO DAMAGING THE PRODUCT.

Step 4

Ensure all bolts are fully locked into position.

The End Table is ready to be used.

Caution: This End Table can only be used on a flat, level surface.

5 OF 6

Label Picture Description QTY

Left Arm with Leg

Panel

Caution : You must read this before you proceed

CAUTION : This Chair is NOT a TOY. Keep your child / children at bay in the process of

assembly.

For turning the chair and to prevent damage to the Table, 02 persons may be needed to execute this

action

ROCKING CHAIR

Noble House Home Furnishings LLS 1 of 8

Right Arm with Leg

Panel

C Backrest Panel 1

D Seat Panel 1

E Seat Cushion 1

F Back Cushion 1

No. Picture Description Qty

①

Long Screw M6x80mm

②

Long Bolts M6x95mm 3

③

Short Bolts M6x80mm 3

④

Sleeve Nut M6x15mm 5

⑤

Short Screw M6x35mm

⑥

Allen Key 2

Noble House Home Furnishings LLS 2 of 8

Before Beginning Assembly:

This Chair has multiple parts and may require up to some 30 minutes to

assemble. To give you an overview of the Chair, the above picture is to help you

put the various parts into perspective. Please read through the instructions here

below to familiarise the parts and steps before assembly.

OVERVIEW

Back Cushion

(F)

Backrest

Panel (C)

Left Leg

Panel (A)

Right Leg Panel

(B)

Seat

Cushion(E)

Seat Panel (D)

FRONT FACING

Noble House Home Furnishings LLS 3 of 8

Step 1

Unpack and place all parts on a clean, non-marring surface.

2.1) Position Seat Panel (D) to Left Leg Panel (A)

Then, position Right Leg Panel (B) onto Seat Panel (D) as shown in picture

above

2.2) Secure Right Leg Panel (B) to Seat Panel (D) by using Screw (①), and

Allen Key ( ⑥), Then Using Screw(⑤

) and Allen Key(⑥) to secure Seat Panel (D)

with Left Leg (A)

Do not fully tighten the Screws.

Step 2

2.1

2.2

Noble House Home Furnishings LLS 4 of 8

With assistance from your adult partners, turn the Chair into the other side.

Repeat the same process of step 2 to secure Left Leg Panel (A) with Seat Panel

(D) by using Screw( ①), and Allen Key (⑥), Then using Screw(⑤

) and Allen

Key(⑥) to secure Seat Panel(D) with Right Leg Panel (B)

Do not fully tighten the Screws.

Step 3

Step 4

Noble House Home Furnishings LLS 5 of 8

Step 5

Keep Chaiir

Position Backrest Panel (C) to Leg Panels (A & B) as the picture above

Secure Leg Panels (A), (B) to Backrest Panel (C) by using Short Bolts (③)&

Sleeve Nuts (④) and Allen Key (⑥)

Do not fully tighten the Screws.

Turn the Chair right side up.

Position Backrest Panel (C) to Leg Panels (A & B) as the picture above

Secure Leg Panels (A), (B) to Backrest Panel (C) by using Long Bolts (②)&

Sleeve Nuts (④) and Allen Key (⑥)

Do not fully tighten the Screws.

Noble House Home Furnishings LLS 6 of 8

Inspect the Chair and make sure all parts are connected.

Place Back Cushion (F) and Seat Cushion (E) onto the Chair

Tie the velcro straps of Back Cushion (F) to Backrest Panel (C) and Seat

Cushion (E) to Seat Panel (D).

Your Chair is ready for use.

This Chair can only be used on a flat, level surface.

Step 6

Noble House Home Furnishings LLS 7 of 8

Noble House Home Furnishings LLS 8 of 8

Noble House 53865 Operating instructions

Brand: Noble House

Model: 53865

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Noble House 53865 Operating instructions

This manual is also suitable for

Noble House 53865 Operating instructions

Related papers

Other documents