VYNCO VMEVBT is a versatile and durable solution for preparing a location for an EV charger installation. Made from high-quality materials, it offers secure mounting options and easy wiring integration. With its compact design and convenient features, it ensures a safe and efficient charging experience.
VYNCO VMEVBT is a versatile and durable solution for preparing a location for an EV charger installation. Made from high-quality materials, it offers secure mounting options and easy wiring integration. With its compact design and convenient features, it ensures a safe and efficient charging experience.
INSTALLATION INSTRUCTION
VYNCO.CO.NZ
VMEVBT
VMEVBT
BASE BOX
FRONT COVER
INTERNAL MOUNTING SLOTS
SIDE TABS
FINISH:
MATERIAL:
REVISION:
DESCRIPTION:
SHEET 1 OF 1
A3
SIZE
APPROVED BY:
PART No:
388 Tuam St
Christchurch
New Zealand
P:
03 379 9283
W:
vynco.co.nz
UNLESS OTHERWISE STATED ALL DIMENSIONS ARE IN MILLIMETRES
ALL CRITICAL TOLERANCES SPECIFIED IN DRAWING
NON SPECIFIED TOLERANCES:
LINEAR: 0.0 ±0.5 0.00 ±0.1 ANGULAR: ±0.5°
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF VYNCO INDUSTRIES
(N.Z.) LTD. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION
OF VYNCO INDUSTRIES (N.Z.) LTD IS PROHIBITED.
DRAWN BY:
DRAWN DATE:
CHANGE BY:
CHANGE DATE:
APPROVED DATE:
- - -
VMEVB
VM EV READY KIT INCLUDING TEMPORARY COVER
AS ASSEMBLED
-
soppitb
24/08/2021
-
-
24/08/2021
XXXX
DRAWING NOT TO SCALE
VMEV BOX AHEAD KIT
WITH TEMPORARY COVER
This instruction covers the installation and safe termination of wiring for the VMEV Box Ahead
kit only. For full VMEV charging installation please refer to appropriate instruction manual.
INSTALLATION INSTRUCTION
VYNCO.CO.NZ
VMEVBT
To ensure your safety, please read and follow
all instructions carefully.
Always isolate the power before installation
or doing any maintenance work.
Do not install this Box Ahead Kit in a position
where the nal charger may get damaged
from vehicles, bikes, machinery, or other
moving objects.
Ensure there is adequate clearance around
the mounting position for safe operation
of the EV charger.
This product must be installed and wired
according to the AS/NZS 3000 Wiring
Rules and be ready for an EV charger to
be installed to meet the Worksafe Electric
Vehicle Charging Safety Guidelines –
available at www.worksafe.govt.nz.
The EV charger must be permanently
connected to a power supply and be
supplied from a dedicated nal sub-circuit.
SAFETY PRECAUTIONS
This Box Ahead Kit must be installed in a
location and position suitable for the VMEV
charger.
MOUNTING POSITION
VMEV charger is suitable for indoor
installation only.
Select a suitable mounting position on
an indoor wall. The position must be at
least 800mm above the oor or ground
and 300mm from any wall or corner.
WARRANTY
This product is covered by the standard 3
Year Vynco Warranty - proof of purchase is
required. Please contact Vynco for details of
returns procedure.
NOTE: This product contains NO user
serviceable parts.
INSTALLATION INSTRUCTION
VYNCO.CO.NZ
VMEVBT
Isolate the power before installation
Switch power on only after complete
installation and examination of the circuit.
INSTALLATION INSTRUCTIONS
1. Frame the installation location to suit
the dimensions of the base box. Ideal
framing will allow the secure xing
of the base box on a minimum of two
sides, leaving the top open for wiring
installation.
2. Fold out the 4x side tabs of the
base box. Insert the base box into the
pre-prepared framing. Ensure the arrow
is orientated upwards. The side tabs
will stop the box at the correct height
on the framing to align with standard
10mm wall linings.
3. Securely fasten the base box to the
framing through the internal
mounting slots.
4. Open the plastic junction box by
removing the two securing screws.
Pull the supply wiring through the top
open bung and safely terminate the
Phase and Neutral wires using the
supplied single screw terminals.
5. Using the supplied double screw
terminal connect the supply earth cable
to the earth wire attached to the base
box. Enclose all wiring terminations
inside the plastic junction box and
secure closed with two securing screws.
L = Live or Phase – Brown or Red
E = Earth – Green/Yellow
N = Neutral – Blue or Black
6. Finish wall lining around the base box.
A standard 10mm wall lining should
nish ush with the front sides of the
base box leaving an open space for an
EV charger to be installed in the future.
7. Secure the front white cover over
the base box using the screws supplied.
Ensure that screws are not over
tightened as this will damage the cover.
AUCKLAND
9 Levene Place, Mount Wellington
PO Box 12 249, Penrose, Auckland 1061
New Zealand
P +64 9 525 6051 F +64 9 525 5799
VYNCO INDUSTRIES (NZ) LIMITED
CHRISTCHURCH
388 Tuam Street, Phillipstown, Christchurch, 8011
PO Box 9022, Tower Junction, Christchurch 8149
New Zealand
P +64 3 379 9283 F +64 3 379 6838
VYNCO.CO.NZ
INSTALLATION INSTRUCTION
-
1
-
2
-
3
-
4
VYNCO VMEVBT is a versatile and durable solution for preparing a location for an EV charger installation. Made from high-quality materials, it offers secure mounting options and easy wiring integration. With its compact design and convenient features, it ensures a safe and efficient charging experience.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
VYNCO 2CS1W Home Card Switch User manual
-
VYNCO V40TSPACER METER BOARD TO INCREASE Operating instructions
-
VYNCO VMC51 User manual
-
VYNCO VMC34D User manual
-
VYNCO VMC34 User manual
-
VYNCO VMC51 User manual
-
VYNCO INSV0102 User manual
-
VYNCO VMEV User manual
-
VYNCO VM17 User manual
-
VYNCO 88USBM2 User manual
Other documents
-
Country Hearth Woodfires Series Operating instructions
-
Masport LE 3000/W Owner's Manual & Installation Manual
-
Blue Seal Blue Seal G1100 Owner's manual
-
ONKYO TX-SR703 User manual
-
Westinghouse SI910SA User manual
-
Tyco Vigilant MX1-Au Wiring Diagrams
-
-
Woodsman Totara Installation Instructions Manual
-
Blue Seal E56 Owner's manual
-
turbofan G32MS Specification
