VYNCO VMC51 User manual

Brand
VYNCO
Model
VMC51
Type
User manual

VYNCO VMC51 is a 51-way combined meter board designed for indoor installation in wall cavities with a minimum stud size of 90mm and a minimum plasterboard/wall covering of 10mm. It features a metal wall enclosure with six fold-out tags for setting the correct height onto studs, removable door hinge pins for reversing the door's swing direction, and separate earth, neutral, and RCD neutral busbars. The VMC51 is rated for a maximum operational voltage of 415V AC, a maximum current of 100A, and a rated insulation voltage of 1000V. It also has a short circuit withstand rating of 10kA.

VYNCO VMC51 is a 51-way combined meter board designed for indoor installation in wall cavities with a minimum stud size of 90mm and a minimum plasterboard/wall covering of 10mm. It features a metal wall enclosure with six fold-out tags for setting the correct height onto studs, removable door hinge pins for reversing the door's swing direction, and separate earth, neutral, and RCD neutral busbars. The VMC51 is rated for a maximum operational voltage of 415V AC, a maximum current of 100A, and a rated insulation voltage of 1000V. It also has a short circuit withstand rating of 10kA.

INSTALLATION INSTRUCTIONS
AUCKLAND
9 Levene Place, Mount Wellington
PO Box 12 249, Penrose, Auckland 1061
New Zealand
P +64 9 525 6051
VYNCO INDUSTRIES (NZ) LIMITED
CHRISTCHURCH
388 Tuam Street, Phillipstown, Christchurch, 8011
PO Box 9022, Tower Junction, Christchurch 8149
New Zealand
P +64 3 379 9283
E [email protected]
VYNCO.CO.NZ
VMC51 / VMC51BK - 51 WAY COMBINED METER BOARD
INSV0058
SPECIFICATIONS
Rated Operational
Voltage
415V AC maximum,
50Hz
Maximum Current 100A
Rated Insulation Voltage 1000V
Short Circuit Withstand 10kA
DIMENSIONS
Cover Assembly 800 x 402 x 35mm
Base Box Dimensions 754 x 355 x 106mm
SAFETY
This product complies in full with AS/NZS 61439.3.
This product should be installed by a suitably
qualied person in accordance with Australian
and New Zealand wiring rules.
IP40
INSTALLATION PROCEDURE
This product is designed to be installed inside a wall
cavity with a minimum stud size of 90mm and a
minimum plaster board/wall covering of 10mm.
For surface mounting use VMCC surface mount
enclosure in conjunction with this board.
The metal wall enclosure must be earthed. Fold out
tags (x6) on the side walls of the enclosure can be
folded out to set the correct height onto the studs.
Door hinge pins are easily removable and the door
can be reversed so that it swings either left or right.
This product is designed to be used with New
Zealand and Australia’s MEN system.
DO NOT install a link between the neutral bars
and earth bar on circuits dedicated to RCDs.
Please ensure circuits and protective devices
are adequately identied during installation.
WARRANTY
This product is covered by a 1 Year Vynco Warranty -
proof of purchase is required. Please contact Vynco
for details of returns procedure.
NOTE: This product contains NO user serviceable parts.
INSTALLATION INSTRUCTIONS
VYNCO.CO.NZ
EARTH AND NEUTRAL BUSBAR LAYOUT
Material Number of Bars Double Screw Tunnels Single Screw Tunnels
Earth Bar Brass with steel screws 1340
Neutral Bar Brass with steel screws 1422
RCD Neutral Bar Brass with steel screws 813
REMOVING DOOR
STEP 1
Rotate top pin 90°.
STEP 2
Slide pin down to release door. There is no need
to remove pin completely.
STEP 3
Lift and remove door.
STEP 1 STEP 2
STEP 3
FITTING DIAGRAM
To t into wall cavity, fold out tabs to set height of
enclosure onto studs.
FITTING DIAGRAM
VMC51 / VMC51BK - 51 WAY COMBINED METER BOARD
  • Page 1 1
  • Page 2 2

VYNCO VMC51 User manual

Brand
VYNCO
Model
VMC51
Type
User manual

VYNCO VMC51 is a 51-way combined meter board designed for indoor installation in wall cavities with a minimum stud size of 90mm and a minimum plasterboard/wall covering of 10mm. It features a metal wall enclosure with six fold-out tags for setting the correct height onto studs, removable door hinge pins for reversing the door's swing direction, and separate earth, neutral, and RCD neutral busbars. The VMC51 is rated for a maximum operational voltage of 415V AC, a maximum current of 100A, and a rated insulation voltage of 1000V. It also has a short circuit withstand rating of 10kA.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents