Linear AM-RPR Operating instructions

Linear
Brand
Linear
Model
AM-RPR
Type
Operating instructions

Nortek Control AM-RPR is a remote proximity receiver designed for use with Linear’s AE1000Plus, AE2000Plus, and AM3Plus access control systems. It functions as a remote PBUS device that supplies localized radio reception for the controller. The AM-RPR allows placement of a unit by each controlled opening without the possibility of the transmitter being detected by the wrong receiver.

The AM-RPR has a two-color indicator on the faceplate that displays the receiver’s status. The indicator lights red when the receiver is getting DC power from the controller and turns green when access is granted to a transmitter.

Nortek Control AM-RPR is a remote proximity receiver designed for use with Linear’s AE1000Plus, AE2000Plus, and AM3Plus access control systems. It functions as a remote PBUS device that supplies localized radio reception for the controller. The AM-RPR allows placement of a unit by each controlled opening without the possibility of the transmitter being detected by the wrong receiver.

The AM-RPR has a two-color indicator on the faceplate that displays the receiver’s status. The indicator lights red when the receiver is getting DC power from the controller and turns green when access is granted to a transmitter.

AM-RPR
Remote
Proximity
Receiver
Installation
Instructions
INTRODUCTION
The AM-RPR remote proximity receiver is designed for use with Linear’s
AE1000Plus, AE2000Plus, and AM3Plus access control systems. The
AM-RPR functions as a remote PBUS device that supplies localized radio
reception for the controller.
In a typical installation, the AM-RPR would be mounted in a plastic
single-gang electrical box next to the controlled opening. When the user
requires access, their transmitter must be activated within three inches
of the AM-RPR faceplate. The ultra-short range of the AM-RPR allows
placement of a unit by each controlled opening without the possibility of the
transmitter being detected by the wrong receiver.
A two-color indicator on the AM-RPR faceplate displays the receiver’s
status. The indicator lights red when the receiver is getting DC power from
the controller and turns green when access is granted to a transmitter.
The AM-RPR remote proximity receiver connects to the controller through a
six-wire cable. A small ferrite ‘doughnut’ is supplied for the wiring to reduce
radio reception in the wires. A rotary switch in the AM-RPR selects the
PBUS device address for the receiver. Each remote device connected to the
controller must be set to a different device address. Power is supplied to the
receiver from the controller.
A special test mode can be selected to test the radio reception. When the
unit is powered and the device address selector is set to 7, activating a
transmitter in range of the receiver causes the test beeper to sound and the
indicator to blink.
1. TYPICAL INSTALLATION
2. LOCATE COMPONENTS 3. INSTALL SWITCH BOX & ROUTE WIRING 4. CONNECT AM-RPR TO CONTROLLER
USA & Canada (800) 421-1587 & (800) 392-0123
(760) 438-7000 - Toll Free FAX (800) 468-1340
www.linearcorp.com
EACH AM-RPR EQUALS 4 LOAD UNITS
CABLE LENGTH FORMULA FOR EACH AM-RPR USED IN SYSTEM
CABLE RUN CABLE TYPE
FORMULA
300 FEET MAXIMUM
BELDEN 9931 (24 AWG)
WEICO 9405 (20 AWG)
FEET x LOAD UNITS < 3,000 MAXIMUM
FEET x LOAD UNITS < 10,000 MAXIMUM
500 FEET MAXIMUM
CABLE TO CONTROLLER
(SEE FORMULA
)
AM-RPR
ELECTRIC STRIKE
ON DOOR
(IN JAMB)
DEVICE
ADDRESS
SELECTOR
TEST
BEEPER
(OTHER SIDE)
POWER & DATA
TERMINALS
(CONNECTS TO CONTROLLER)
INSTALL
ELECTRICAL
BOX IN WALL
ROUTE WIRING
FROM CONTROLLER TO
ELECTRICAL BOX
STRIP BACK WIRE'S OUTER INSULATION 8 INCHES
WRAP WIRES 3 OR 4 TIMES AROUND THE
FERITE "DOUGHNUT" (THIS KEEPS THE
TRANSMITTERS FROM BEING RECEIVED
ALONG THE CABLE)
AM-RPR
AM-RPR
TERMINALS
PCLK
DVAL
DAT0
DAT1
GND
PWR
GND
DAT1
DAT0
DVAL
PCLK
PWR
ACCESS CONTROL
SYSTEM PBUS
TERMINALS
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,AM-RPR PROXIMITY RECEIVER- LINEAR P/N: 211773 C - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 1 OF 2
Copyright © 2012 Linear LLC 211773 C
5. PRELIMINARY RECEIVER TEST 6. SET DEVICE ADDRESS 7. INSTALL RECEIVER AND FACEPLATE
SET DEVICE
ADDRESS SELECTOR
TO POSITION 7
TURN CONTROLLER
POWER SWITCH ON
ACTIVATE A
TRANSMITTER NEAR
RECEIVER
INDICATOR SHOULD
BLINK WHEN
TRANSMITTER
IS NEARBY
SET DEVICE
ADDRESS
SELECTOR
TO CORRECT
DEVICE ADDRESS
SET DEVICE ADDRESS SELECTOR TO POSITION 1-6
(MUST BE SET DIFFERENT FROM ANY OTHER
REMOTE DEVICE IN THE SYSTEM)
MOUNT RECEIVER INTO
ELECTRICAL BOX USING
LONG SCREWS
ATTACH FACEPLATE
WITH SHORT SCREWS
8. PROGRAM SYSTEM 9. TEST SYSTEM LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship for
twelve (12) months. This warranty extends only to wholesale customers who
buy direct from Linear or through Linear’s normal distribution channels. Linear
does not warrant this product to consumers. Consumers should inquire from
their selling dealer as to the nature of the dealer’s warranty, if any. There are
no obligations or liabilities on the part of Linear LLC for consequential
damages arising out of or in connection with use or performance of
this product or other indirect damages with respect to loss of property,
revenue, or profi t, or cost of removal, installation, or reinstallation. All
implied warranties, including implied warranties for merchantability and implied
warranties for fi tness, are valid only until the warranty expires. This Linear LLC
Warranty is in lieu of all other warranties express or implied.
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an
RPA# and other important details
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fi ll an important
need in portable wireless signalling. However, there are some limitations which
must be observed.
* For U.S. installations only: The radios are required to comply with FCC Rules and Regulations
as Part 15 devices. As such, they have limited transmitter power and therefore limited range.
* A receiver cannot respond to more than one transmitted signal at a time and may be blocked by
radio signals that occur on or near their operating frequencies, regardless of code settings.
* Changes or modifi cations to the device may void FCC compliance.
* Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
* A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
distributor or dealer, and these facts should be communicated to the ultimate users.
PROGRAM THE CONTROLLER
TO CONFIGURE THE PBUS
DEVICE
REFER TO THE CONTROLLER
PROGRAMMING INSTRUCTIONS
FOR DETAILS
ACTIVATE TRANSMITTER
WITHIN 3" OF RECEIVER
FACEPLATE
INDICATOR WILL CHANGE
FROM RED TO GREEN IF THE
TRANSMITTER IS GRANTED
ACCESS
PRINTER’S INSTRUCTIONS:
INSTR,INSTL, AM-RPR PROXIMITY RECEIVER - LINEAR P/N: 211773 C - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - SCALE: 1-1 - SIDE 2 OF 2
  • Page 1 1
  • Page 2 2

Linear AM-RPR Operating instructions

Linear
Brand
Linear
Model
AM-RPR
Type
Operating instructions

Nortek Control AM-RPR is a remote proximity receiver designed for use with Linear’s AE1000Plus, AE2000Plus, and AM3Plus access control systems. It functions as a remote PBUS device that supplies localized radio reception for the controller. The AM-RPR allows placement of a unit by each controlled opening without the possibility of the transmitter being detected by the wrong receiver.

The AM-RPR has a two-color indicator on the faceplate that displays the receiver’s status. The indicator lights red when the receiver is getting DC power from the controller and turns green when access is granted to a transmitter.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents