Factory Furniture CUBIT Edge Planter & Seating Operation and Maintenance Manual

Brand
Factory Furniture
Model
CUBIT Edge Planter & Seating
Type
Operation and Maintenance Manual

This manual is also suitable for

factoryfurniture.co.uk
Cubit Planters
OPERATION & MAINTENANCE MANUAL
factoryfurniture.co.uk
Introduction
Design
Design, shop drawings and development by
Factory Furniture Ltd.
Manufacture
Factory Furniture manufactured components. Products
are assembled in Factory workshops, checked and
dispatched ready for installation. Replacement products
or components thereof should be ordered direct from
Factory Furniture Ltd.
Copyright
The design copyright for the product and drawing
copyright remains the sole property of Factory Furniture
Ltd.
General Specifications
Example configurations
0.7 x 0.5 x 0.45 / 0.9m Folded Planter
Metric length 710mm | width 500mm | height 450 or
900mm
Imperial length 2’ 4” | width 1’ 7½” | height 1’ 5½” or 2’
11½”
Fixing Centres 450mm (1’ 5½”) x 350mm (1’ 2”)
Approx Weight 49kg (450mm) or 89kg (900mm)
Planter Capacity 140ltr (450mm) or 295ltr (900mm)
0.7 x 0.5 x 0.45 / 0.9m Stepped Planter
Metric length 710mm | width 500mm | height 450 or
900mm
Imperial length 2’ 4” | width 1’ 7½” | height 1’ 5½” or 2’
11½”
Fixing Centres 450mm (1’ 5½”) x 270mm (10½”)
Approx Weight 51kg (450mm) or 88kg (900mm)
Planter Capacity 130ltr (450mm) or 285ltr (900mm)
Ø1.5 x 0.45 / 0.9m Curved Planter
Metric length 1500mm | width 1500mm | height 450 or
900mm
Imperial length 4’ 11” | width 4’ 11” | height 1’ 5½” or 2’
11½”
Fixing Centres 1270mm (4’ 2”) x 1270mm (4’ 2”)
Approx Weight 96kg (450mm) or 170kg (900mm)
Planter Capacity 690ltr (450mm) or 1475ltr (900mm)
Detailed Material & Finish
Specifications
Planter Wall Modules
• Planter wall modules manufactured from lasercut
Corten steel sheet (all welded construction). A mild
steel option is available.
• Corten steel assemblies are left untreated. Mild steel
assemblies are hot dip galvanised and polyester
powder coated (colour grey as standard or to
customer specification).
• Assemblies are bolted together using M10 bolts and
locknuts to form planter.
General Maintenance
(Recommended Schedule & Guidelines)
Daily/Weekly/Monthly (or as adopted)
Visual checks of planter - check over for superficial or
physical damage.
Three Monthly
Clean all items as detailed below check all fixings are
seated correctly.
Six Monthly
Secure all fixings; full clean as detailed below.
Specific Maintenance Details
Corten Steel
Clean as required (but at least every three months) with
warm soapy water.
Polyester Powder Coated & Galvanised
For general cleaning using a damp cloth and warm
soapy water only. Scourers and abrasive cleaners are
NOT suitable for this type of finish and may damage it.
Before using any cleaning agents to remove grati etc.
try on a small, inconspicuous area first to avoid causing
more unsightly damage.
factoryfurniture.co.uk
Repairs
Corten Steel
There is no need to repair light damage (scratches,
chips etc.) to the rust coloured layer on the surface of
the Corten steel. This layer will naturally reform within a
short period of time in an external environment.
Polyester Powder Coated & Galvanised Surfaces
For light damage (scratches, chips etc.) repair using
touch-up paint to match original colour (available
from Factory Furniture Ltd). Paint application should
be carried out in accordance with approved methods
detailed by the paint manufacturer. Please note that
it is advisable to use professional painters to achieve
best results when touching up larger areas. Products
for respraying larger areas are available from Factory
Furniture Ltd.
Heavy Damage
In the event of serious damage to any component,
replacements should be ordered from Factory Furniture
Ltd. In this event (or if the product needs to be
disassembled for any reason), please contact Factory
Furniture for detailed technical advice.
factoryfurniture.co.uk
500
100
250
100
1000
50
500
50 254 354
0.5 x 0.45 / 0.9m Folded
Planter Module
0.45 / 0.9m Folded End
Planter Module
1.0 x 0.45 / 0.9m Folded
Planter Module
0.45 / 0.9m Folded
Corner Planter Module
2.0 x 0.9m Folded
Planter Module
2.0 x 0.45m Folded
Planter Module
2000
2000
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
0.7 x 0.5m Folded Planter (example only)
Cubit Planter
(Folded)
1. If necessary assemble planter using wall modules,
spacers and M10 bolts and nuts provided.
2. Install suitable foundation pads (see illustration or
to suit planter for larger planter assemblies) with top
face at ground level.
3. Position planter in correct orientation with planter
central on foundation pads.
4. Mark hole positions through base.
5. Remove the planter; drill holes Ø12mm x 90mm
deep (or as bolt manufacturer’s recommendations)
6. Clear debris from holes7.
7. Reposition planter and fix to foundation pads using
zinc-coated M10 x 75mm sleeve anchors tightened
to 50Nm (or as per manufacturer’s instruction).
8. Check level and reinstate ground if necessary
710 500
Ground
level
300 x 300 x 600mm
C20 Concrete Foundation Pad
(recommendation only)
450 (or 900mm)
0.5m
Module
0.5m
Module
End
Module
End
Module
Base Fix
Spacer
Base Fix
Spacer
450 (Ctrs) 350 (Ctrs)
M10 x 25mm
hex bolt and
M10 lock nut
M10 x 25mm
hex bolt into
M10 lock nut
Base fix
spacer
M10 x 75mm
s
leeve anchor
Folded
body panel
factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
0.7 x 0.5m Stepped Planter (example only)
Cubit Planter
(Stepped)
1. If necessary assemble planter using wall modules,
spacers and M10 bolts and nuts provided.
2. Install suitable foundation pads (see illustration or to
suit planter for larger planter assemblies) with top
face at ground level.
3. Position planter in correct orientation with planter
central on foundation pads.
4. Mark hole positions through base.
5. Remove the planter; drill holes Ø12mm x 90mm
deep (or as bolt manufacturer’s recommendations)
6. Clear debris from holes
7. Reposition planter and fix to foundation pads using
zinc-coated M10 x 75mm sleeve anchors tightened
to 50Nm (or as per manufacturer’s instruction).
8. Check level and reinstate ground if necessary
450 (Ctrs)
710 500
Ground
level
300 x 300 x 600mm
C20 Concrete Foundation Pad
(recommendation only)
450 (or 900mm)
0.5m
Module
End
Module
End
Module
Base Fix
Spacer
Base Fix
Spacer
0.5m
Module
270 (Ctrs)
500
100
250
100
1000
90
500
90 254 354
0.5 x 0.45 / 0.9m
Stepped Planter Module
0.45 / 0.9m Stepped End
Planter Module
1.0 x 0.45 / 0.9m
Stepped Planter Module
0.45 / 0.9m Stepped
Corner Planter Module
2.0 x 0.45m Stepped
Planter Module
2.0 x 0.9m Stepped
Planter Module
2000
2000
M10 x 25mm
hex bolt into
M10 lock nut
Stepped
body panel
M10 x 25mm
hex bolt and
M10 lock nut
Base fix
spacer
M10 x 75mm
s
leeve anchor
factoryfurniture.co.uk
Installation Instructions
All installation works to be carried out by competent
personnel - install as complete unit.
Ø1.5m Curved Planter (example only)
Cubit Planter
(Curved)
1. If necessary assemble planter using wall modules,
spacers and M10 bolts and nuts provided.
2. Install suitable foundation pads (see illustration or
to suit planter for larger planter assemblies) with top
face at ground level.
3. Position planter in correct orientation with planter
central on foundation pads.
4. Mark hole positions through base.
5. Remove the planter; drill holes Ø12mm x 90mm
deep (or as bolt manufacturer’s recommendations)
6. Clear debris from holes
7. Reposition planter and fix to foundation pads using
zinc-coated M10 x 75mm sleeve anchors tightened
to 50Nm (or as per manufacturer’s instruction).
8. Check level and reinstate ground if necessary
M10 x 25mm
hex bolt into
M10 lock nut
Stepped
body panel
M10 x 25mm
hex bolt and
M10 lock nut
Base fix
spacer
M10 x 75mm
s
leeve anchor
5 Pioneer Road, Faringdon,
Oxfordshire SN7 7BU
+44 (0)1367 242731
[email protected].uk
1270 (Ctrs)
1500
1600 x 300 x 1600mm
C20 Concrete Foundation Pad
(recommendation only)
450 (or 900mm)
R750
0.75m Curved
Module
Base Fix
Spacer
Base Fix
Spacer
Base Fix
Spacer
Base Fix
Spacer
0.75m Curved
Module
0.75m Curved
Module
0.75m Curved
Module
1058
280
162
R750
R 0.75 x 0.45 / 0.9m
Curved Planter Module
R 0.75 x 0.45 / 0.9m
Curved Planter Module
474
R250
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Factory Furniture CUBIT Edge Planter & Seating Operation and Maintenance Manual

Brand
Factory Furniture
Model
CUBIT Edge Planter & Seating
Type
Operation and Maintenance Manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents