INSTALLATION & MAINTENANCE INSTRUCTIONS
HEAVY DUTY FLOODLIGHT 75 SERIES
(VERTIAL AND HORIZONTAL LAMP)
American Electric Lighting a division of Acuity Lighting Group, Inc. Conyers, GA
DRAWING NO. B60974 REV E (FRONT)
©2003 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-60974
REMOVABLE
PLUG SCREWS
CLAMPING
BOLTS (2)
MOUNTING
HOLES
KNUCKLE BOLT
SET SCREWS (4)
TENON
CLOSURE SCREW
WIRING
COMPARTMENT
POWER CORD ENTRY
THIS UNIT HAS BEEN DESIGNED WITH FOUR WEEP HOLES. TWO
HOLES IN THE FRONT BEZEL AND TWO HOLES IN THE WIRING
COMPARTMENT AREA. HOLES IN WIRING COMPARTMENT ARE PLUGGED
WITH TWO SCREWS. THESE SCREWS ARE TO REMAIN IN THIS POSITION
WHEN UNIT IS MOUNTED FACING DOWNWARD. WHEN UNIT IS INSTALLED
FACING UPWARD THE TWO SCREWS ARE TO BE REMOVED AND PLACED
INTO WEEP HOLES IN THE FRONT BEZEL
WEEP HOLES
YOKE - THE YOKE HAS 3 MOUNTING HOLES, ONE FOR A 3/4"
BOLT AND TWO FOR 3/8" BOLTS. MOUNTING ADAPTERS ARE
AVAILABLE TO ALLOW FOR HORIZONTAL ADJUSTMENT ON POLE
TOPS, CROSS ARM, ETC. IF MOUNTING ADAPTERS ARE NOT USED
THE FLOODLIGHT MUST BE AIMED IN THE HORIZONTAL DIRECTION
DESIRED PRIOR TO INSTALLATION. VERTICAL ADJUSTMENT IS
ACCOMPLISHED BY LOOSENING THE TWO CLAMPING BOLTS
WHICH HOLD THE YOKE TO THE HOUSING. ROTATE HOUSING TO
THE DESIRED ANGLE BY USING EITHER THE AIMING ANGLES
MARKED ON THE YOKE. TIGHTEN THE CLAMPING BOLTS.
MOUNTING AND AIMING
WIRING
YOKE - OPTIONAL FACTORY PRE-WIRED FLOODS ARE FURNISHED
WITH 3 FEET OF FLEXIBLE CABLE READY FOR CONNECTION TO
SUPPLY. FOR STANDARD UNITS THAT ARE NOT PRE-WIRED, OPEN
BEZEL BY LOOSENING THE 1/4" CLOSURE SCREWS LOCATED AT TOP
OF FLOOD. LIFT THE FIBER SHIELD TO EXPOSE THE WIRING
COMPARTMENT. REMOVE THE COMPRESSION FITTING AND GROMMET,
FEED CABLE THROUGH THE WIRE ENTRY HOLE. SLIP THE GROMMET
AND COMPRESSION FITTING OVER CABLE AND REASSEMBLE TO
HOUSING. USING THE WIRING DIAGRAM AS A GUIDE, MAKE
CONNECTIONS TO EITHER THE TERMINAL BLOCK OR THE PIG TAILS.
MULTI-VOLT BALLAST ARE FACTORY WIRED FOR 120 VOLT OPERATION.
CABLE SHOULD BE NO. 16 AWG MINIMUM, TYPE SJ, SO, OR SJT-WA,
SUITALBE FOR 60×C OPERATION.
TENON - THE TENON MOUNT WILL SLIP FIT ONTO A 2 OR
2 1/2 INCH PIPE. LOOSEN TENON FITTER KNUCKLE BOLT
AND ROTATE TO DESIRED ANGLE. TIGHTEN KNUCKLE BOLT
AND SET SCREWS.
TENON - OPEN ACCESS DOOR ON TENON MOUNT, FEED SUPPLY
WIRES THROUGH BOTTOM OF TENON MOUNT AND OUT ACCESS DOOR.
SLIP TENON MOUNT OVER POLE TENON AND CONNECT SUPPLY LEADS
TO FIXTURE WIRES. PUSH LEADS BACK INTO WIRING COMPARTMENT
OF TENON MOUNT AND REPLACE COVER.
WARNING
ENSURE UNIT IS PROPERLY GROUNDED AND DISCONNECT POWER DURING INSTALLATION AND
BEFORE SERVICING TO AVOID THE RISK OF SEVERE OR FATAL ELECTRICAL SHOCK
!
American Electric Lighting a division of Acuity Lighting Group, Inc. Conyers, GA
DRAWING NO. B60974 REV E (BACK)
©2003 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-60974
ALTERNATE
SOCKET
BRACKET
LOCATION
CLOSURE
SCREW
REFLECTOR
SCREWS (2)
SOCKET
BRACKET
HORIZONTAL REFLECTOR
VERTICAL REFLECTOR
THE SOCKET BRACKET HAS THREE SETS OF SOCKET MOUNTING
HOLES (BACK, CENTER, & FRONT) CONSULT CHART FOR DESIRED
BEAM PATTERN. IF BEAM PATTERN DESIRED IS POSSIBLE WITH
REFLECTOR SUPPLIED REMOVE SOCKET SCREWS AND MOVE SOCKET
TO POSITION INDICATED IN CHART.
IT IS ALSO POSSIBLE TO ROTATE THE REFLECTOR 90í IN HOUSING.
TO DO SO FIRST REMOVE THE TWO SCREWS HOLDING THE REFLECTOR
IN PLACE AND REMOVE REFLECTOR. NEXT REMOVE THE (ONE) SCREW
HOLDING THE SOCKET BRACKET DOWN AND LIFT SOCKET BRACKET OFF
OF LOCATING BOSS. PLACE SOCKET BRACKET ON THE OTHER SOCKET
BRACKET BOSS AND REPLACE SCREW. ROUTE SOCKET WIRES SO WHEN
REFLECTOR IS REPLACED THEY ARE NOT BETWEEN REFLECTOR AND
HOUSING. REMOVE FIBER SHIELD FROM REFLECTOR AND REMOUNT ON
OTHER SET OF HOLES. REPLACE REFLECTOR.
B E A M P A T T E R N C H A R T
REFLT FINISH
DIFFUSED
REPORT NO.
AE4703I.PHT
AE4706I.PHT
AE4713I.PHT
BEAM SPREAD
6H X 6V
7H X 6V
5H X 3V*
SCKT POSITION
CENTER (B)
HPS
MH
OPEN BEZEL BY LOOSENING THE 1/4"
CLOSURE SCREW LOCATED AT TOP OF
FLOOD. LOOSEN THE 8 LENS CLIP
SCREWS AND ROTATE CLIPS.
REMOVE OLD LENS PARTS AND INSTALL
NEW LENS. ROTATE LENS CLIPS
AND TIGHTEN LENS CLIP SCREWS.
LENS REPLACEMENT
CENTER (B) 7H X 6V AE4694I.PHT SEMI SPECULAR
VERTICAL
MH
CENTER (B) SEMI SPECULAR
SEMI SPECULAR
---
BACK (A)
HORIZONTAL
---
---
---
HPS
SEMI SPECULAR
AE4715I.PHT
AE4721I.PHT
AE4724I.PHT
5H X 4V*
5H X 3V*
5H X 5V*
CENTER (B)
---
---
FRONT (C) 5H X 2V* AE4711I.PHT SEMI SPECULAR
---
CENTER (B) DIFFUSED
DIFFUSED
---
CENTER (B)
HPS
HPS
MH
MH
MH ---
BACK (A) 5H X 4V* AE4722I.PHT SEMI SPECULAR
* BEAM SPREAD BASED ON 20% OF MAX. CANDLEPOWER
REFLECTOR AND SOCKET ADJUSTMENT
/
