INSTALLATION & MAINTENANCE INSTRUCTIONS
ACP COMPACT FLOODLIGHT
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
DRAWING NO. A71218 REV B (FRONT)
©2007 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-71218
REMOVABLEREMOVABLE
PLUG PLUG
SCREWS (3)SCREWS (3)
CLAMPINGCLAMPING
BOLTS (2)BOLTS (2)
MOUNTING
HOLES
CLOSURE CLOSURE
SCREWS (2)SCREWS (2)
WARNING
ENSURE UNIT IS PROPERLY GROUNDED AND DISCONNECT POWER DURING INSTALLATION AND
BEFORE SERVICING TO AVOID THE RISK OF SEVERE OR FATAL ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
!
BOLT TO A MAXIMUM OF 400 INCH ILBS.BOLT TO A MAXIMUM OF 400 INCH ILBS.
RETIGHTEN BOLT TO SECURE TENON MOUNT.TIGHTENRETIGHTEN BOLT TO SECURE TENON MOUNT.TIGHTEN
ACP COMPACT FLOOD TO DESIRED ANGLE ANDACP COMPACT FLOOD TO DESIRED ANGLE AND
ANGLE. LOOSEN BOLT IN CENTER OF TENON MOUNTEDANGLE. LOOSEN BOLT IN CENTER OF TENON MOUNTED
INDICATED ON TENON FOR DETERMINING DESIREDINDICATED ON TENON FOR DETERMINING DESIRED
AND LOCK NUTS RETIGHTENED. INDEX MARKS AREAND LOCK NUTS RETIGHTENED. INDEX MARKS ARE
MADE. SET SCREWS SHOULD THEN BE RETIGHTENEDMADE. SET SCREWS SHOULD THEN BE RETIGHTENED
SHOULD BE LOOSENED AND HORIZONTAL ADJUSTMENTSHOULD BE LOOSENED AND HORIZONTAL ADJUSTMENT
THE SET SCREWS AND LOCK NUTSTHE SET SCREWS AND LOCK NUTS
TENON MOUNT:TENON MOUNT:
TO A MAXIMUM OF 400 INCH LBS.TO A MAXIMUM OF 400 INCH LBS.
MENT MADE AND THEN BOTH BOLTS RETIGHTENEDMENT MADE AND THEN BOTH BOLTS RETIGHTENED
YOKE NEED TO BE LOOSENED, VERTICAL ADJUST-YOKE NEED TO BE LOOSENED, VERTICAL ADJUST-
MOUNTING ANGLES. THE BOLTS ON EACH SIDE OFMOUNTING ANGLES. THE BOLTS ON EACH SIDE OF
EACH SIDE OF YOKE FOR DETERMINING DESIREDEACH SIDE OF YOKE FOR DETERMINING DESIRED
INDEX MARKS ARE INDICATED ONINDEX MARKS ARE INDICATED ON
YOKE MOUNT:YOKE MOUNT:
ADJUSTMENT:ADJUSTMENT:
PIPE TENON. TIGHTEN ALL FOUR SET SCREWS EQUALLY PIPE TENON. TIGHTEN ALL FOUR SET SCREWS EQUALLY
TO A MAXIMUM OF 350 INCH LBS., THEN TIGHTEN EACH TO A MAXIMUM OF 350 INCH LBS., THEN TIGHTEN EACH
LOCK NUT TO A MAXIMUM OF 350 INCH LBS. TO LOCK NUT TO A MAXIMUM OF 350 INCH LBS. TO
SECURELY ATTACH FIXTURE TO TENON TOP. SECURELY ATTACH FIXTURE TO TENON TOP.
TENON MOUNT CAN BE MOUNTED TO A 2" OR 2 1/2"TENON MOUNT CAN BE MOUNTED TO A 2" OR 2 1/2"
THE COMPACT FLOOD WITH OPTIONALTHE COMPACT FLOOD WITH OPTIONAL
TENON MOUNT:TENON MOUNT:
THE YOKE HAS 3 MOUNTING HOLES, THE YOKE HAS 3 MOUNTING HOLES,
ONE FOR A 3/4" BOLT AND TWO FOR 3/8" BOLTS. ONE FOR A 3/4" BOLT AND TWO FOR 3/8" BOLTS.
MOUNTING ADAPTORS ARE AVAILABLE TO ALLOW FORMOUNTING ADAPTORS ARE AVAILABLE TO ALLOW FOR
HORIZONTAL ADJUSTMENT ON POLE TOPS, CROSS HORIZONTAL ADJUSTMENT ON POLE TOPS, CROSS
ARMS, ETC. HORIZONTAL ADJUSTMENT MUST BE ARMS, ETC. HORIZONTAL ADJUSTMENT MUST BE
DETERMINED BEFORE MOUNTING THE YOKE TO THEDETERMINED BEFORE MOUNTING THE YOKE TO THE
CROSSARM IF THE ACP FLOOD IS BEING MOUNTED CROSSARM IF THE ACP FLOOD IS BEING MOUNTED
DIRECTLY TO A CROSSARM WITHOUT THOSE OPTIONALDIRECTLY TO A CROSSARM WITHOUT THOSE OPTIONAL
FITTERS.FITTERS.
YOKE MOUNT:YOKE MOUNT:
INSTALLATIONINSTALLATION
THIS UNIT HAS BEEN DESIGNED WITH THREE THIS UNIT HAS BEEN DESIGNED WITH THREE
BREATHING HOLES. TWO HOLES IN THE WIRING BREATHING HOLES. TWO HOLES IN THE WIRING
COMPARTMENT AREA AND 1 HOLES IN THE BEZEL. ALL COMPARTMENT AREA AND 1 HOLES IN THE BEZEL. ALL
HOLES ARE PLUGGED WITH A SCREW. ONLY IF THE UNIT HOLES ARE PLUGGED WITH A SCREW. ONLY IF THE UNIT
IS YOKE MOUNT AND HAS NO PHOTOCONTROL IS YOKE MOUNT AND HAS NO PHOTOCONTROL
RECEPTACLE MUST ANY ACTION BE TAKEN. THE SCREW RECEPTACLE MUST ANY ACTION BE TAKEN. THE SCREW
IN THE BEZEL IS TO BE REMOVED ONLY IF THE UNIT IS IN THE BEZEL IS TO BE REMOVED ONLY IF THE UNIT IS
FACING DOWN. ONE OF THE TWO SCREWS IN THE FACING DOWN. ONE OF THE TWO SCREWS IN THE
WIRING COMPARTMENT IS TO BE REMOVED ONLY IF THE WIRING COMPARTMENT IS TO BE REMOVED ONLY IF THE
UNIT IS FACING UP. CHOOSE THE SCREW THAT IS NOT UNIT IS FACING UP. CHOOSE THE SCREW THAT IS NOT
HOLDING DOWN THE CAPACITOR BRACKET.HOLDING DOWN THE CAPACITOR BRACKET.
BREATHING HOLESBREATHING HOLES
WIRINGWIRING
COMPARTMENTCOMPARTMENT
POWER CORD POWER CORD
ENTRYENTRY
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL
AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
2
1
1
2
7/16
Dia
25/32
Dia
YOKE
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
DRAWING NO. A71218 REV B (REAR)
©2007 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-71218
WIRINGWIRING
YOKE MOUNT: YOKE MOUNT: OPTIONAL FACTORY PRE-WIRED OPTIONAL FACTORY PRE-WIRED
FLOODS ARE FURNISHED WITH 3 FEET OF FLEXIBLE FLOODS ARE FURNISHED WITH 3 FEET OF FLEXIBLE
CABLE READY FOR CONNECTION TO SUPPLY. FOR CABLE READY FOR CONNECTION TO SUPPLY. FOR
STANDARD UNITS THAT ARE NOT PRE-WIRED, OPEN STANDARD UNITS THAT ARE NOT PRE-WIRED, OPEN
BEZEL BY LOOSENING THE 2 CLOSURE SCREWS OR BEZEL BY LOOSENING THE 2 CLOSURE SCREWS OR
LATCHES LOCATED AT THE TOP OF FLOOD. LIFT THE LATCHES LOCATED AT THE TOP OF FLOOD. LIFT THE
SHIELD TO EXPOSE THE WIRING COMPARTMENT. SHIELD TO EXPOSE THE WIRING COMPARTMENT.
REMOVE THE COMPRESSION FITTING AND GROMMET, REMOVE THE COMPRESSION FITTING AND GROMMET,
FEED CABLE THROUGH THE WIRE ENTRY HOLE. SLIP FEED CABLE THROUGH THE WIRE ENTRY HOLE. SLIP
THE GROMMET AND COMPRESSION FITTING OVER THE GROMMET AND COMPRESSION FITTING OVER
THE CABLE AND REASSEMBLE TO HOUSING. USING THE CABLE AND REASSEMBLE TO HOUSING. USING
THE WIRING DIAGRAM AS A GUIDE, MAKE CONNECTIONS THE WIRING DIAGRAM AS A GUIDE, MAKE CONNECTIONS
TO THE TERMINAL BLOCK. ATTACH THE GREEN GROUND TO THE TERMINAL BLOCK. ATTACH THE GREEN GROUND
WIRE TO THE GROUNDING BOSS WITH THE GREEN WIRE TO THE GROUNDING BOSS WITH THE GREEN
GROUND SCREW PROVIDED. MULTI-VOLT BALLAST ARE GROUND SCREW PROVIDED. MULTI-VOLT BALLAST ARE
FACTORY WIRED FOR 120V OPERATION UNLESSFACTORY WIRED FOR 120V OPERATION UNLESS
OTHERWISE SPECIFIED. CABLE SHOULD BE #16 AWG OTHERWISE SPECIFIED. CABLE SHOULD BE #16 AWG
MINIMUM, TYPE SJ, SO, OR SJT-WA, SUITABLE FOR MINIMUM, TYPE SJ, SO, OR SJT-WA, SUITABLE FOR
105C OPERATION105C OPERATION
TENON MOUNT: TENON MOUNT: OPEN ACCESS DOOR ON TENON OPEN ACCESS DOOR ON TENON
MOUNT, FEED SUPPLY WIRES THROUGH BOTTOM OF MOUNT, FEED SUPPLY WIRES THROUGH BOTTOM OF
TENON MOUNT AND OUT ACCESS DOOR. SLIP TENON TENON MOUNT AND OUT ACCESS DOOR. SLIP TENON
MOUNT OVER POLE TENON AND CONNECT SUPPLY MOUNT OVER POLE TENON AND CONNECT SUPPLY
LEADS TO FIXTURE WIRES. PUSH LEADS BACK INTO LEADS TO FIXTURE WIRES. PUSH LEADS BACK INTO
WIRING COMPARTMENT OF TENON MOUNT AND WIRING COMPARTMENT OF TENON MOUNT AND
REPLACE COVER.REPLACE COVER.
BEZEL REPLACEMENTBEZEL REPLACEMENT
OPEN THE BEZEL BY LOOSENING THE 2 SCREWS OROPEN THE BEZEL BY LOOSENING THE 2 SCREWS OR
LATCHES. LOOSEN THE HINGE KEEPER SCREW AND SLIDELATCHES. LOOSEN THE HINGE KEEPER SCREW AND SLIDE
THE BEZEL OFF. ASSEMBLE THE REPLACEMENT BEZEL INTHE BEZEL OFF. ASSEMBLE THE REPLACEMENT BEZEL IN
THE REVERSE MANNER.THE REVERSE MANNER.
LAMP SERVICINGLAMP SERVICING
OPEN THE BEZEL BY LOOSENING THE 2 SCREWS OROPEN THE BEZEL BY LOOSENING THE 2 SCREWS OR
LATCHES. ALLOW IT TO HANG FREELY ON IT’S HINGE.LATCHES. ALLOW IT TO HANG FREELY ON IT’S HINGE.
THE LAMP SHOULD THEN BE UNSCREWED COUNTERTHE LAMP SHOULD THEN BE UNSCREWED COUNTER
CLOCKWISE UNTIL FREE. THE LAMP CAN THEN BE CLOCKWISE UNTIL FREE. THE LAMP CAN THEN BE
REPLACED BY REVERSING THE PROCEDURE.REPLACED BY REVERSING THE PROCEDURE.
ENSURE WHEN RELAMPING TO USE THE CORRECTENSURE WHEN RELAMPING TO USE THE CORRECT
LAMP TYPE AND VALUE. LAMP TYPE AND VALUE.
RELAMP IN ACCORDANCE WITH THE BALLASTRELAMP IN ACCORDANCE WITH THE BALLAST
EMPLOYED FOR A MAXIMUM OF 400W HPS OR 400W MH.EMPLOYED FOR A MAXIMUM OF 400W HPS OR 400W MH.
SETSET
SCREWS (4)SCREWS (4)
HINGEHINGE
SCREWSCREW
ACCESSACCESS
DOORDOOR
YOKE MOUNT
TENON MOUNT
IF LAMP IS MARKED IF LAMP IS MARKED
IT CONTAINS MERCURY.IT CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORGSEE WWW.LAMPRECYCLE.ORG
Hg
REV
DATE
DESCRIPTION ECN
BY
APP
PART NUMBER.
057-70-71218
DESCRIPTION DWG NUMBER
A71218
SHT 3 OF 3
--
25-JUL-2005
NEW RELEASE
R034503
MAH DAH
INSTALLATION INSTRUCTIONS
ACP COMPACT FLOOD
A
28-FEB-2007
ADD TEXT FOR PEC AND RELAMPING
R040067
MAH
DAH
R042055
GEW
JRC
6-NOV-2007
B
ADD LAMP HG NOTE
/
