AKR 651 IX

Whirlpool AKR 651 IX Program Chart

  • Hello! I am an AI chatbot trained to assist you with the Whirlpool AKR 651 IX Program Chart. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
5019 318 33189
Installation sheet
Minimum height above cooker: 60cm (electric cookers), 75cm (gas, gas oil or coal cookers). To install
follow points (1
Ö
2
Ö
3
Ö
.....). Do not connect the appliance to the electrical power supply until
installation is completed. If the installation instructions for the gas cooker specify a greater distance,
this must be taken into account.
Contact a qualified technician for installation.
GB
31833189GB.fm Page 1 Wednesday, December 21, 2005 3:37 PM
5019 318 33189
31833189GB.fm Page 2 Wednesday, December 21, 2005 3:37 PM
5019 318 33189
31833189GB.fm Page 3 Wednesday, December 21, 2005 3:37 PM
5019 318 33189
Assembly - fig. 1-2-3-4
In order to facilitate installation of the hood and flue support, trace a centre line on the wall between the hob and ceiling (
Z
).
Position the template against the wall, then mark and drill the holes where indicated (
Y
).
Insert two wall plugs with hooks (
V
).
Hang the hood and adjust the position by turning the adjustment screws (
S
).
Remove the grease filters and mark the holes for secure fixing (
T-R
).
Remove the hood and drill the holes (4 x
Ø
8 mm).
Insert 4 wall plugs and two screws in the top holes: they will ensure secure fixing (
X
).
Fix the flue support (
Z
) as close as possible to the ceiling with two screws and wall plugs.
Important! Check that the support is perfectly aligned with the hood.
Rehang the hood on the wall.
Fix the hood with two screws at the bottom (
D
).
Installing the exhaust pipe (Extractor version)
Warning! The exhaust pipe and clamps are not supplied and must be bought separately.
Connect one end of the exhaust pipe (
J
) to the hood (
G
) with the other end directed to the outside.
Installing the deflector (Filter version)
Fix the deflector (
F
) to the flue support with 4 screws.
Connect the deflector to the hood with an exhaust pipe.
Warning! The exhaust pipe and clamps are not supplied and must be bought separately.
Installing the telescopic flue
Connect the hood to the power supply.
Fix the telescopic flue (
M
) to the support (
Z
) with two screws and let it slide down to its specific seat on the top of the hood.
TR GB
31833189GB.fm Page 4 Wednesday, December 21, 2005 3:37 PM
5019 318 33189
PRODUCT DESCRIPTION SHEET
1.
Control panel
2.
Grease filters
3.
Lighting unit
4.
Telescopic flue
5.
Grease filter release-replace handle
Removing and renewing or washing the
grease filter
1.
Disconnect the electrical power supply.
2.
Remove the grease filters (
Fig. 5
):
a
- push the handles backwards
b
- then downwards.
3.
After the grease filter has been replaced or cleaned
(depending on model), refit the parts in reverse order,
making sure the entire extraction surface is covered.
Replacing bulbs
1.
Disconnect the electrical power supply.
2.
Remove the grease filters.
3.
Remove the burnt-out bulb.
Replace using 40W max (E14) bulbs only.
4.
Refit the lighting unit.
Fitting or renewing the carbon filter - Fig. 6:
1.
Disconnect the electrical power supply.
2.
Remove the grease filters.
3.
If the filters are not already fitted, locate one on each side
to cover both motor protection grilles, check that pins
R
on the duct align with slots
S
, then turn it clockwise until
it locks.
4.
To remove the carbon filter, proceed in reverse order.
5.
Replace the grease filters.
CONTROL PANEL
A.
Light switch.
B.
Speed selector switch.
Fig. 5
Fig. 8
Fig. 7
Small amount of
steam and fumes
Medium amount of
steam and fumes
Large amount of
steam and fumes
Fig. 6
TR GB
31833189GB.fm Page 5 Wednesday, December 21, 2005 3:37 PM
/