2. olympia electronics
  3. GR-900-30L-SC
GR-900-30L-SC

olympia electronics GR-900-30L-SC User manual

  • Hello! I'm your chat assistant. I've reviewed the datasheet for the Olympia Electronics Emergency Luminaire GR-900/30L/SC/ADR. This document provides detailed technical specifications, installation instructions, and operational details, highlighting features such as its self-testing function, super capacitor backup, and waterproof design. I'm ready to answer your questions about this product.
  • What is the minimum autonomous duration of the luminaire?
    What is the charging time for the capacitors pack?
    What is the light source in the luminaire?
    What is the operation temperature range?
To install the luminaire follow the installation
instructions on page 4.
GENERAL
This luminaire is used in places where
emergency luminaires are needed.
E a c h l u m i n a i r e m u s t b e p e r m a n e n t l y
connected to mains power supply.
In normal operation the led strip lights and the
capacitors pack is charging.
In case of a mains power supply failure the
luminaire will light the led strip automatically
in emergency mode. When the mains power
supply is restored the device turns to normal
operation.
INSTALLATION
Capacitors pack charging
The luminaire enters in this operation when the
mains power supply fails and capacitors pack
has lost its energy. During this operation the
luminaire enters the idle state and the
capacitors pack’s consumption is negligible.
The capacitors pack charging is completely and
accurately controlled. In this case, is achieved
the perfect capacitors pack maintenance, as
well as the elongation of its duration. When the
capacitor has completely charged, it charges
with a maintenance current.
Capacitors pack Cut-off
Page 1 from 8
GR-900/30L/SC/ADR Addressable Waterproof Self Testing Maintained Emergency Luminaire
220-240V AC/50-60Hz
TECHNICAL CHARACTERISTICS (for LED module specifications see page 8)
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
RATED MAXIMUM OPERATING TEMPERATURE OF WINDINGS
EXTERNAL DIMENSIONS (L x W x H)
TYPICAL WEIGHT
GUARANTEE
The controlgear has mains-connected windings of transformer.
Controlgear is suitable for LED module only.
CONTROL GEAR WITH
AUTOMATIC TEST FUNTION
OPERATION VOLTAGE
SUPPLY CURRENT
MAXIMUM POWER CONSUMPTION
INSULATION BETWEEN SUPPLY &
CAPACITORS PACK CIRCUIT
BACK UP SOURCE
CHARGING TIME
INDICATIONS - CONTROLS
CAPACITOR PROTECTION
MIN. MAX. CHARGE VOLTAGE
MIN. MAX. CHARGE CURRENT
MIN. MAX. DISCHARGE VOLTAGE
MIN. MAX. DISCHARGE CURRENT
MINIMUM AUTONOMOUS DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
LIGHT SOURCE INTENSITY
ILLUMINATION SOURCE
6h
CHARGE, LAMP FAULT, BAT FAULT, TEST button
From overcharge / the control gear will recharge the capacitors pack
normally after the test of 22.3 (IEC61347-2-7:2011, §22.3).
o o
-40 to 65 C (70 C, occasionally)
Up to 95%
3 years
363 x 145 x 73 mm
White LEDs
6W / 6.5VA /PF: 0.92
IP65
60 min
250lm (230V AC) / 90lm (emergency)
1100gr.
Super Capacitors pack A-900/SC
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
Thank you for your trust in our products
Olympia Electronics - European manufacturer
923900003_09_001
25mA
U-OUT
23V
100mA
2W
Basic insulation
Prated
Irated
0 - 260mA
90 - 290mA
0 - 7.8V
2.5 - 7.8V
O
t : 130 C
w
ABS/PC, PC
CONSTRUCTION MATERIAL
Push the TEST/RESET button (page 3) for >10
seconds, to delete all the indicated LED errors .
Then the illumination sign enters regular
operation mode.
The Automatic Autonomy Test includes all the
features provided by Manual Autonomy Test.
This test is conducted automatically every six
months. In order to be performed, the main
power supply and the capacitors pack should
be connected and fully charged. If the
capacitors pack is not fully charged, the test is
postponed until it becomes fully charged. If
there is a failure in autonomy test, the
capacitors should be changed.
Back Up Operation
Automatic Autonomy Test
The capacitors pack’s autonomous duration
during emergency mode is at least the one that
is stated in the list of the technical
characteristics. During emergency mode, a
LED strip test is also performed.
Resetting Errors
Manual Test
Automatic Operational Test
This test includes all the operations that
provide the manual test and is conducted
automatically every 15 days. In order to be
performed, the main power supply and the
capacitors pack should be connected.
If the Test button is pressed for a period
between 5 to 10 seconds (with the capacitors
pack fully charged), the illumination sign will
enter in counting autonomy condition. If the
capacitors pack is not fully charged this
command is ignored.
The manual test can be conducted only if the
main power supply and the capacitors pack is
connected. By pressing the TEST/RESET
button briefly (page 3) an emergency operation
test is initiated. During this test period all
indication LEDs are OFF and the whole
emergency circuit is monitored.
The BAT FAULT LED blinks during the
measurement, indicating this process to the
user. This measurement duration is equal with
the nominal autonomous duration of the
luminaire and at the end of the process, if the
measured duration is equal to the nominal
autonomous duration, the BAT FAULT LED is
turned OFF, in the other hand stays
continuously ON. If there is a failure in
autonomy test, the capacitors should be
changed.
Manual Autonomy Test
5. I s not allowed to discard capacitors t i
pack into common trash bins, they must
be discarded only in recycling points.
Do not incinerate.
2. The luminaire must be connected to the
mains power supply thru a fuse dependent by
the total amount of the line’s power load.
1. Operations for installation, maintainance or
testing must be done by authorized personel
only.
ΑΤΤΕΝΤΙΟΝ!!!
Addressable Communication
Pressing the test switch less than 5 seconds will
initiate a light source test (last for 3 secs).
3 . I n c a s e o f ca p a ci t or s p ac k or l a mp
replacement, these must be replaced by parts of
the same type, by the manufacturer or by a
competent person.
4. In case of inactive use for a period greater
than 2 months, disconnect the capacitors pack
by pulling out the connector when is fully
charged.
Test switch
Pressing the test switch between 5 to 10
seconds will initiate a manual capacitors pack
duration test. This test will not be started if the
capacitors pack is not fully charged (i.e. If the
green LED is flashing). If the test switch is
pressed for more than 10 seconds, the
illumination sign will be reset (delete all errors).
The luminaire has the ability to be connected to
GR-6500 panel. In order to do so, the
luminaire’s address has to be unique in the
same bus. For more information, on page 4.
Page 2 from 8923900003_09_001
Status of LEDs
Led status explanation
Normal
Charging
Capacitors pack’s duration test (auto or manual)
Capacitors pack’s fault
Capacitors pack’s fault and light source fault
Charger and capacitors pack’s fault (or mains off and capacitor fault)
Charger and light source fault (or mains off and light source fault)
Charger, capacitors pack and light source fault (or mains off, capacitors pack and light source fault)
Light source test
Light source fault
Continuous ON Continuous OFF Flashing at 1,2 Hz
Charger’s fault, capacitors pack not connected or mains off
YELLOW
RED
LEDs Description
GREEN
Page 3 from 8923900003_09_001
type 2x1mm² or any other type, at least equal to it’s mechanical and electrical properties).
Step 5. Connect the mains cables to the respective terminal block. Ν for neutral, L for live wire and L1 for
the maintained operation. The L1 wire can be connected to an external switch to control the maintained or
non maintained operation of the luminaire. For permanent maintained operation use two wires to power
the luminaire, Ν for neutral and L for live wire, and link the L and L1.
Step 9. Finally place the diffuser by using the 4 screws (tightening torque 1.2Nm).
Step 6: Pass the 2 signal cables and connect them on the A, B terminals minding the correct polarity.
These cables are used to connect the luminaire to GR-6500 panel. Set the module address throught the
dip switch positions, according to page 5,6 and 7. is optional, for termination purposes only.
In order to test or reset the device you must carefully remove the diffuser by unfastening the 4
mounting screws. Then push the button as described in the according paragraphs on page 1 and 2.
NOTE!!
Step 7. Install the included tie (if needed) to fasten securely the power cables.
BEWARE of electric shock after reflector removal. Plastic base could contain live parts if
connected to mains supply.
Step 2. Install the included plastic cover in to the unused hole and install the base plastic (with the
included mounting screws and plugs).
Step 8. Refit the reflector and fasten the two small screws (included).
After finishing the installation you must power the luminaire at least for 6 hours for capacitor
charging to perform the nominal autonomy.
Step 10. Manual TEST or Resetting Errors
Step 1. Remove the diffuser. Place a flat blade screwdriver and pull up gently the reflector.
to ensure the tightness isolation IP 65). Install the cable gland, pass the round cable through and
tighten it all the way.
Step 3. Always use in any case round mains cable, with external diameter of 6-9mm (H05RN-F
ATTENTION!! The cable must not be deformed in any way (This requirement is important
Step 4. Place the capacitors pack’s connector to the corresponding connector on the PCB.
1
ON
2345678
Dipswitch
Position
1
4
8 9
7
10
INSTALLATION INSTRUCTIONS (For wall or ceiling installation)
2 3
5 6
N
L
Link
Permanent maintained operation
b)
L
N
External
switch
Controlled operation of the lamp
a)
Power Connections Communication Connection
N NL
A
B
Communication Connection
BA
LL1 L1
Page 4 from 8923900003_09_001
Address Address Address Address
Dipswitch
setting Dipswitch
setting Dipswitch
setting Dipswitch
setting
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
1 1 1
1
1
1
1
1
1
1
1 1 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11
ON ON ON
ON
ON
ON
ON
ON
ON
ON
ON ON ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ONON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ONON
2 2 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2 2 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
3 3 3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3 3 3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4 4 4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4 4 4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
555
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
555
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6 6 6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6 6 6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7 7 7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7 7 7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8 8 8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8 8 8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
1
2
3
4
Page 5 from 8923900003_09_001
Address Address Address Address
Dipswitch
setting Dipswitch
setting Dipswitch
setting Dipswitch
setting
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
1
1
1 1
1
1
1
1
1
1
1
1
1
1 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
11
ON
ON
ON ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ONON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ONON
2
2
2 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2
22
2
22
2
2
2 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2
22
2
22
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2
22
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
22
2
22
2
22
2
3
3
3 3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3 3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
4
4
4 4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4 4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
5
5
5 5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5 5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
6 6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6 6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7 7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7 7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
8
8
8 8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8 8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
121
122
123
124
Page 6 from 8923900003_09_001
Address Dipswitch
setting
245
246
247
248
249
250
1
1
1
1
1
1
1
1
1
1
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
4
5
5
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
7
8
8
8
8
8
8
8
8
8
8
241
242
243
244
Page 7 from 8923900003_09_001
Important notice for the installed luminaires in one area !!!
The installer must connect the capacitors pack’s connector first and then should power the
luminaire. The capacitors pack connection must have at least a time variation of 1.5 minute for
each luminaire. With this variation, it is ensured that the non synchronized Automatic
Autonomous Test for two or more luminaires installed in one area, is not conducted in the same
day.
Super capacitors pack replacement (Α-900/SC)
It can be done only by a competent person and after
the mains interruption
1. Unfasten the 4 screws (step 9 page 4) and remove the
diffuser. Unfasten the 2 retaining screws and remove the
reflector (step 8 page 4).
2. Disconnect the connector and remove the old capacitors
pack by unfastening the retaining screws .
3. Connect the new capacitors pack (step 4 of the installation procedure) place it in the position
of the old one and fasten the removed screws.
4. Refit the removed parts in previous steps and power the device.
s
Non Maintained operation: The luminaire lights its
illumination source, only in power supply’s failure.
(*) Maintained operation: The luminaire lights its
illumination source, when it is powered by the mains
power supply or not.
Note!! The installer should fill in, on the specification
label, the letter G if the luminaire is used as a safety
sign.
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
1: Maintained (*)
A: Including test device
B: Including remote test mode
G: Internally illuminated safety sign
60: 1 hour duration
C: Including inhibiting mode
NOTE! The light source is non-user replaceable.
The light source contained in this luminaire shall only be replaced by the manufacturer, or his
agent, or a similar qualified person.
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.com
[email protected]
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A.
45 °C max. across the board
Cable connection with non reversible connectors
17.4-21.6V DC
2W
GR-900/30L/SC/ADR
1505153
X1 6 0A GB C
SS
Page 8 from 8923900003_09_001
/