Introduction
What’s in the box
What you’ll need
●TD52 Video Intercom
●A #2 Phillips screwdriver or
power drill with a #2 Phillips driver bit
●1/2 inch (12.7mm) drill bit, or larger, for
routing cable through wall
●1/8 inch (3mm) drill bit for pilot holes
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
ACC-INT-SURF Video Intercom Surface Mount Box
Compatible Products
●TD52 Video Intercom
●ACC-INT-HOOD
●ACC-POE-2WIRE
Hole Patterns
A
B
C
D
E
Direct wall mounting
Double gang junction box
U.S. Single gang junction box
Octagonal Junction Box
U.K. Single gang junction box
3
●4x 6-32 x 3/4” button head screws
●4x 8-32 x 3/4” button head screws
●4x #10x1.5” wood screws
●4x wall anchors
●Conduit adapter
●Drain hole plug
Mounting
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
4
Installation
For a solid material like wood or metal,
drill 1/8 inch pilot holes. Drive mounting
screws directly into the pilot holes using
hole pattern A of the Surface Mount Box.
Feed Ethernet cable through the center of
the Surface Mount Box before fully
securing it to the mounting surface.
Leave enough slack to safely handle the
TD52 Video Intercom during installation.
For drywall, plaster or masonry, separate
wall anchors may be required.
For installation onto a junction box, use
the corresponding mounting holes and
provided machine screws.
.
Attach the TD52 Video Intercom to
the Surface Mount Box using the
screws provided in the with the TD52.
For detailed mounting instructions related to
Verkada TD52 Video Intercom, see its install
guide
Mounting
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
5
Installation
To use the conduit adapter, loosen the
screws and remove the conduit adapter
cover from the bottom of the Surface
Mount Box. Use the same screws to
attach the conduit adapter in its place.
The Surface Mount Box is reversible and
can be mounted with the conduit
adapter facing upwards or downwards.
For installations with the conduit adapter
facing upwards, remove the drain hole
plug from the upper drain holes and
place it into the drain holes on the
opposite side of the Surface Mount Box.
When installed, the drain hole plug should
always be on the top side of the device.
Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
Copyright © Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
you're experiencing issues or need assistance, please contact our
24/7 Technical Support Team immediately.
Sincerely,
The Verkada Team
verkada.com/support
6
-
1
-
2
-
3
-
4
-
5
-
6
Verkada Video Intercom Surface Mount Box Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Verkada ACC-INT-HOOD Installation guide
-
Verkada TD52 Video Intercom Installation guide
-
-
-
-
-
Verkada CM41 Installation guide
-
-
-
Other documents
-
Verkeda SV11 User guide
-
Henny Penny BW-4 User manual
-
-
-
-
-
-
-
-