Verkada ACC-MNT-POLE-1 Installation guide
- Type
- Installation guide
Introduction
What’s in the box
What you’ll need
●Compatible Verkada product
●A #2 Phillips screwdriver or
power drill with a #2 Phillips driver bit
●1/2 inch (12.7mm) drill bit, or larger, for
routing cable through wall
●Utility knife
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
© Copyright 2023 Verkada Inc. All rights reserved.
ACC-MNT-POLE-1
Compatible products
For a list of compatible products, please visit:
https://docs.verkada.com/docs/accessories
-overview.pdf
Small Pole Straps (2 pcs)
Pole Diameter: 48-107mm (1.9-4.2”)
Drive: #2 Phillips
M4x0.7 Machine Screw (4 pcs)
Length: 14mm Drive: #2 Phillips
2
Large Pole Straps (2 pcs)
Pole Diameter: 84-178mm (3.3-7.0”)
Drive: #2 Phillips
Temporary Zip Tie (1 pcs)
Pole Diameter: 48-178mm (1.9-7.0”)
Mounting on a small pole
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
© Copyright 2023 Verkada Inc. All rights reserved.
4
Installation
For poles with diameter of less than 3.2” (81 mm).
A zip tie is provided to aid in the install
process. Make sure to remove it once
installation is completed.
Position the Pole Mount in the desired
location.
Route the temporary zip tie through the
top, front slot and around the pole.
Route a small pole strap through the
bottom, front slot and around the pole.
Tighten with a #2 Phillips head screwdriver
or drill bit.
Remove the temporary zip tie with a utility
knife and repeat the former installation
step on the top, front slot.
David Sun
For small poles:
"Begin installation by routing the zip tie through the front
slot at the top and around the pole. After using the zip tie to
temporarily secure the pole mount, begin routing the small
pole strap through the front slot at the bottom of the mount
and tighten it with a #2 Phillips head drill. Finally, remove
the zip tie and replace it with the second small pole strap.
Tighten the pole strap with a #2 Phillips head drill. The pole
mount should now be securely fastened to the pole."
Secure the mount to the pole
by tightening the pole straps.
Once complete, mount a
compatible Verkada product
onto the Pole Mount.
See the install guide of your
compatible Verkada product for
further mounting instructions.
Mounting on a large pole
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
© Copyright 2023 Verkada Inc. All rights reserved.
5
Installation
For poles with diameter of more than 3.2” (81 mm).
A zip tie is provided to aid in the install
process. Make sure to remove it once
installation is completed.
Position the Pole Mount in the desired
location.
Route the temporary zip tie through the
top, side slots and around the pole.
Route a large pole strap through the
bottom, side slots and around the pole.
Tighten with a #2 Phillips head screwdriver
or drill bit.
Remove the temporary zip tie with a utility
knife and repeat the former installation
step on the top, side slots.
David Sun
For big poles:
"Begin installation by routing the zip tie through the side
slots at the top and around the pole. After using the zip tie
to temporarily secure the pole mount, begin routing the
proper pole strap through the side slots at the bottom and
tighten it with a #2 Phillips head drill. Finally, remove the zip
tie and replace it with the second pole strap. Tighten the
pole strap with a #2 Phillips head drill. The pole mount
should now be securely fastened to the pole."
Secure the mount to the pole
by tightening the pole straps.
Once complete, mount a
compatible Verkada product
onto the Pole Mount.
See the install guide of your
compatible Verkada product for
further mounting instructions.
Appendix
Support
Verkada Inc. 405 E 4th Ave, San Mateo, CA 94401
All specifications are subject to change without notice
© Copyright 2023 Verkada Inc. All rights reserved.
Thank you for purchasing this Verkada product. If for any reason
you're experiencing issues or need assistance, please contact our
24/7 Technical Support Team immediately.
Sincerely,
The Verkada Team
verkada.com/support
6
-
1
-
2
-
3
-
4
-
5
-
6
Verkada ACC-MNT-POLE-1 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Verkada ACC-MNT-CORNER-1 Installation guide
-
-
-
-
-
Verkada AD33 Installation guide
-
-
-
Verkada CH52-E User manual
-
Other documents
-
Verkeda SV11 User guide
-
Henny Penny BW-4 User manual
-
-
-
-
-
-
-
-