Zip HydroChill HC45 User manual

Zip
Brand
Zip
Model
HydroChill HC45
Type
User manual
1
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk
Installation instructions & user manual
Zip
HydroChill
HC45 Under-counter chiller range.
Model number:
HC45T128, HC45T228
2
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Table of contents
Important safety instructions ....................................................................................................................2
Warnings and regulatory information .......................................................................................................3
Technical data ...............................................................................................................................................4
Major components supplied with the HydroChill & accessories ...................................................................4
Spare parts ..................................................................................................................................................... 5
Before installation..........................................................................................................................................6
Installation
Section 1 Water block ....................................................................................................................................7
Section 2 Ventilation .....................................................................................................................................9
Section 3 Tap installation ..............................................................................................................................12
Section 4 Generic Command Centre installation instructions ...................................................................... 13
Section 5 HydroChill Chilled only products installation , HC45T128 .............................................................14
Section 6 HydroChill Chilled ambient products installation , HC45T228 ......................................................15
Section 7 Commissioning .............................................................................................................................. 16
Operation ......................................................................................................................................................16
Filter replacement .........................................................................................................................................17
Air inlet screen ..............................................................................................................................................17
Cleaning, service & general maintenance .....................................................................................................18
Warranty information and end of life disposal...............................................................................................19
Contact details ..............................................................................................................................................20
This manual contains important safety and installation instructions for the HydroChill.
Please read all warnings, installation requirements and installation instructions before
installing the HydroChill system.
Installation
This system must be installed in accordance with water supply byelaws, current IEE regulations and
relevant local authority byelaws.
Electrical o
The appliance must be connected to the supply through an isolating switch with a contact
separation of at least 3mm in all poles and be protected by a suitably rated RCD.
To protect the appliance, an MCB (miniature circuit breaker) or cartridge fuse must be fitted with a
rating suitable for the nominal current of the appliance.
Safety
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
Refrigerant
The Zip HydroChill Command Centre contains R134a refrigerant under pressure. Maintenance
of the refrigeration unit must be carried out by an accredited service provider or qualified
refrigeration technician.
!
IMPORTANT SAFETY INSTRUCTIONS
3
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
IMPORTANT SAFETY INSTRUCTIONS
Qualifications
If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards,
all installation procedures must be carried out by a suitably qualified tradesperson. The power cable
and power outlet must be in a safe visible position for connection.
Lifting
Take care when lifting. The Command Centre may exceed safe lifting limits. If you feel this is
beyond your personal capabilities, please seek assistance with the lift. The weight of the Command
Centre is marked on the packaging. Do not lift the Command Centre by the front cover or any of its
connections. Refer to the technical specification, see page 4, for the weight of the product.
Airflow
The Zip HydroChill operates within the ambient temperature range 5ºC - 35ºC. Proper air circulation
must be provided. The system will operate satisfactorily only if the recommended air gaps are
provided. See Section 2 'Ventilation', page 9 for correct installation to prevent overheating.
Sanitising
For safe operation, the HydroChill is designed to be installed, commissioned and used within 48
hours.
Should the HydroChill not be required for an extended period of time (48 hours or more), do not fill
and commission it until ready for first use.
The HydroChill must be sanitised during the commission process, please contact the Zip Water
team on 0345 6 005 005 to book your commissioning service.
For water taste and quality reasons any non-use of more than 48 hours, Zip recommend a system
flush be performed.
On first use after a period of non-use, run the chilled & ambient water functions for 60 seconds to
flush the filter and system.
Not flushing the system may affect water the quality.
WARNINGS AND REGULATORY INFORMATION
Warnings
• The Zip HydroChill
must be earthed. The resistance of the earth connection
from each exposed metal part must be less than 1Ω.
• All installation and service work must be completed by trained and suitably
qualified tradespeople. Faulty operation due to unqualified persons working on
this product, or any other Zip product may void warranty coverage.
• As the installer, it is your responsibility to supply (if necessary) and install all
valves as required by local regulations and relevant standards.
• The HydroChill is rated for 230V 50Hz AC operation.
• Do not remove the cover of the appliance under any circumstances without
first isolating the appliance from the power supply.
• Never locate the Command Centre near, or clean with water jets.
• Do not expose the Zip HydroChill
to the elements of nature.
• Due to the process of continuous improvement, Zip reserves the right to
change details mentioned in this manual, without notice.
• Visit www.zipwater.co.uk to ensure you have the latest copy of this document.
!
4
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Technical data
Model Description
Dispense rating
Litres/hr
Dispense
options
Power
rating
kW
Refrigerant
Under-counter
chiller dimensions
W x D x H (mm)
Weight
Empty
Kg*
HC45T128 HC45 single lever tap 28 Chilled 0.33 R134a 280 x 475 x 335 18.5
HC45T228 HC45 twin lever tap 28 Chilled, Ambient 0.33 R134a 280 x 475 x 335 18.5
• 15mm compression fitting connecting to mains water supply.
• A wholesome water supply is required with minimum water pressure of 0.15 MPa (1.5 bar). If the incoming
mains cold water supply pressure exceeds 0.7 MPa (7.0 bar) a pressure reducing valve is required to be
fitted in the supply line. (See Accessories below).
• Power Supply: 230V AC, 13A.
• Chiller type. Fan cooled condenser with compressor. Operating temperature range 5ºC - 35ºC.
• Refrigerant type: Non-toxic R134a.
• Tap: Chrome plated brass, lever action, vented with swivel head.
• Filtration type: 3 micron filtration.
To order spare parts and accessories Call Zip on 0345 6 005 005.
Accessories
Item Part No. Description
Optional HE45004 Water block (water shut down system)
AQ3 Pressure reducing valve (3.5 bar)
Accessories
* Weight is chiller unit only with no accessories
Components supplied with the HydroChill
Supplied parts
Qty Description
1 Hose flexible inlet
1 IEC power cable UK
1 ChillTap vented self-return HD tap
1 Vent - side outlet
1m Tube insulation 6mm
1 Vent kit,4 parts
1 Installation instructions
1 T25 torx double ended key
9 Door buffer self adhesive
1 Branch stem tee 3 x 1/4”
5
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Spare parts
Spare parts
Item Part No. Description
1 SP93249 Compressor Tecumseh THB4422YWZ
2 SP91513 Relay Compressor Tecumseh THB4422YWZ
3 SP91515 Capacitor Compressor Tecumseh THB4422YWZ
4 SP91514 Overload Compressor Tecumseh THB4422YWZ
5 93703UK Filter
6 94358 Filter Head 45 Deg
7 SP91461 Fan
9 94379 IEC Socket Assy
10 SP93230 Power Switch
11 SP91552 1/2” BSP - 1/4” JG Adapator
12 91482 500 KPa Pressure Limit Valve
13 SP91487 Inlet Bush Assy
14 95130 Pressure Relief Valve
15 95126 Leak Detector
16 95127 Leak Detector Pads
17 SP91459 Filter Screen & Holder
18 95135 JG Fittings Kit G4 UCCT
19 SP99445 Vented Tap light duty twin lever
19 SP99249 Vented Tap HD single lever
20 95131 Evaporator S/S
21 SP7036 Thermostat Chillers
23 SP90056 Hose Inlet Kit
6
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Before installation
Before installation ensure that the following have been provided at the
installation site
•
Review of all the technical specifications.
•
Ensure the under counter cupboard floor can support the product weight when
full of water (allow an extra 3.6kg when full).
•
Sufficient space in the cupboard to install the Command Centre and other
components in accordance with these installation instructions. See Technical
specification, page 4 for dimensions.
•
For Zip HydroChill HC45 models, 1 x 220-240V AC 13A socket will be required.
•
The Command Centre must be installed in accordance with IEE regulations, See
Technical specification, page 4 for power ratings.
Note Check all cable and hose lengths against inlet /outlet positions before
proceeding (see section 5 & 6 for general layout).
•
A wholesome water supply connection with a minimum working pressure of: (see
page 4 min. / max. water supply pressure) with isolating valve inside the cupboard
within reach of the braided hoses and positioned so that the connection point
and the stop cock will not be obstructed when the Command Centre is installed.
•
If pressure is likely to exceed 0.7 MPa (7 bar), install a 0.35 MPa (3.5 bar) pressure
limiting valve.
•
The appliance must be placed with its base in a horizontal position.
IMPORTANT!
Do not proceed with the installation if these requirements are not met.
!
!
7
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Description
• The Water Block is designed to be installed upstream of any Zip product and associated pipe-
work to minimise the potential for water leakage in the event of a system malfunction.
• The Water Block is ideal for limiting potential leakage and resulting water damage from water
heaters, water chillers etc. when fitted in supply pipe work that is subject to mains water pressure.
• Once set, the Water Block will ensure that the volume of water that can flow through at one time
is limited to a pre-determined maximum, providing the flow rate through it exceeds 2 litres per
minute.
• The Water Block also incorporates a non-return valve.
• The Water Block is WRAS approved.
Precautions
• The Water Block will help to contain leakage exceeding a rate of 2 l/min.
• Note The leakage at lower flow rates may not be detected by the Water Block and could remain
unchecked.
• Appropriate measures should be taken to contain leakage in these circumstances.
Specification
Flow control range 5 - 50 litres
Minimum / Maximum pressure 0.2 - 10.0 bar
Maximum ambient
temperature
40ºC
Maximum water temperature 70ºC
Minimum operating flow rate 1.5 +/- 0.5 litres / min.
Inlet connection ¾" BSP female or 15mm
Outlet connection ¾" BSP male or 15mm
!
Section 1 Water block (optional)
8
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Note. This device must be installed vertically with the direction of flow
downwards (inlet at the top , outlet at the bottom. See Fig 1 adjacent).
• The Water Block should be installed in a convenient location on the water
supply line to the Zip product.
• Pointer ‘P’ (see Fig.3) should be rotated until in line with the maximum required flow at
one time. Each number on the scale corresponds to 5 litres of flow i.e. 1 = 5 litres, 10 = 50
litres.
• The adjustment key (see Fig.2) should be used to adjust the pointer.
• The inlet should be connected via an 15mm isolation valve (not supplied).
• The outlet shall be connected via the 15mm - 1/2” brass compression fitting supplied.
• Ensure that the direction of flow through the Water Block is correct and that the filter
screen (see Fig.2) is inserted correctly with the convex surface facing towards the water
supply.
1.1 Installation
Fig. 2
Fit key to adjust flow
Key
Reset lever
1.2 Reset Procedure
• The Water Block will activate and shut off the supply if more water than the set amount is drawn off at one time.
• In this event firstly isolate and de-pressurise the water supply to the Water Block, identify and repair the cause of
the leak then remove the pipe-work downstream of the Water Block and press the reset button ‘H’ (see Fig.3).
• The reset device (see Fig.2) may be fitted to avoid disconnection. This allows the Water Block to be reset by
operating the lever in the direction shown in Fig.2.
• In the event of persistent tripping contact Zip for advice on 0345 6 005 005.
1.3 Maintenance
• The filter screen should be checked and cleaned periodically subject to water conditions and usage.
Fig. 1
Fig. 3
Direction of flow
Seal
Reset
device
Direction of
flow
Filter
screen
Isolation valve
(not supplied)
15mm - 1/2” brass
compression fitting
Installation - Section 1 Water block
!
9
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
!
Important Read this section in conjunction with section 4 Command Centre installation,
page 13.
When installing air flow vents, the following tools will be required
•
Jigsaw and drill or equivalent equipment.
•
Keyhole or wall board saw.
2.1 Generic requirements
Clearance envelope
• A clearance envelope around all Command Centres must be provided to allow adequate
ventilation for the safe and effective use of the HydroChill system.
!
550mm
50mm
Command
Centre width
Installation - Section 2 Ventilation
50mm
10
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 2 Ventilation
2.3 Preferred ventilation arrangements for commercial models
• The ducted vent kit supplied with the Command Centre exhausting through the kick-space should
be used, to provide adequate ventilation in all conditions. (Ancillary components are not shown in
these diagrams).
• The 100mm separation between inlet and outlet vents must be observed to prevent recirculation of
warm air back into the cupboard space.
2.2 Ventilation for all models
• The clearance envelope dimensions stated in the specification sheets and installation instructions
must be observed.
• Adequate ventilation must be provided to ensure that the cupboard space temperature does not
exceed 35
0
C.
B
A
C
100mm min.
Cupboard back must be
fully closed to prevent
recirculation into cupboard
from kick space.
A
Vent cut-out details
A Air outlet vent
(flat vent)
B Air inlet vent
314
Ø
12 x 2
326
5
43max
285
60
Ø
12 X 4
=
=
45
284
Ø
12 x 4
C Ducted vent
11
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 2 Ventilation
2.4 Alternative arrangement (Vent tray)
In situations where cupboard width is 1000mm or greater, without central pillar and where vent grilles cannot be
fitted in the kick board (e.g. hospitals) use a Vent tray kit (SP93541).
Vent tray
100mm
min.
A vent grille, supplied should be used as an inlet vent and fitted to the cabinet side (adjacent to the Command
Centre air inlet) as shown below. It must take in air from the room or another ventilated space. This space could
be an adjacent cupboard, (via a communicating port) on condition that it does not contain a heat generating
appliance. The vent grille or the
angled inlet grille supplied should
be fitted in the adjacent cupboard,
observing 100mm separation from
the vent tray exhaust.
12
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 3 Tap installation
Ø35mm
Nut
Lower rubber
washer
Upper rubber
washer
Washer
Lower rubber
washer
Nut
Red, white and blue
pipes
Red, white and blue
pipes
3.1 Configure the twin lever tap
Heavy dutyTwin lever
3.2 Cut the hole & mount the tap
3.3 Configure the heavy duty tap
Ø25mm
3.4 Cut the hole & mount the tap
• Cut a Ø35mm hole in the worktop / sink.
Worktop
Worktop
• Tighten the tap nut to secure in place, do not
over tighten.
• Tighten the tap nut to secure in place, do not
over tighten.
• Cut a Ø25mm hole in the worktop / sink.
13
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 4 Command Centre installation
4.2 Push fit fittings
4.1 Generic Command Centre installation instructions
Read these instructions before commencing Command Centre installation,
they apply to all installation arrangements.
!
• Install the mains water braided hoses to the Command Centre before locating in place.
• Ambient mains water braided hose length is 750mm.
• Electrical power cable is 1.8m long.
• The Command Centre
must be installed within the limits of
the hose and cable lengths supplied.
• • All plastic pipes must be cut to size. They must have a All plastic pipes must be cut to size. They must have a
constant fall back to the constant fall back to the Command Centre.
• • Isolation valves are not supplied.Isolation valves are not supplied.
• To avoid water leaks, be careful not to damage the tap pipes.
Pipes must not be kinked around a bend.
If shortening pipes, ensure ends are cut clean and square
(see ‘Push fit fittings’ below).
• Before fitting the tap pipes , remove plugs from the outlet
fittings on the top of the Command Centre by pressing the
collet and simultaneously pulling out the plug.
• Measure and trim the red , white and blue 1/4” coloured
pipes from the tap to the outlet fittings on the top of the
Command Centre. (See sections 5-6 page 14-15).
• Before making the connections insulate the hoses with the
loose length of foam insulation supplied. Trim the insulation
to about 5-10mm shorter than the tube.
• For correct connections, refer to :
Section 5 for HydroChill chilled HC45T128
Section 6 for HydroChill chilled ambient HC45T228
• Push each hose into the quick-release connector as far as it
will go (approx. 15 mm) to ensure a tight connection. (see
‘Push fit fittings’ below).
90º bend
Connect to
HydroChill
Braided hose for mains
water supply
Mains cold
water supply
Water block
(optional)
Isolation valve
14
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 5 Command Centre installation, Chilled only installation
5.1 HydroChill chilled only model
HC45T128
Heavy duty
Clearance
envelope
280mm
50mm
50mm
550mm
Mains cold water
isolation valve
(not supplied)
VENT
CHILLED
OUT
5.2 Manifold connections
5.3 Installation arrangements
Connect to
Red 1/4” pipe from tap
Blue 1/4” pipe from tap
via 1/4” push fit connector
(supplied)
Connect to
White 1/4” pipe from tap
Connect to
Mains (Cat 1) Cold water
supply
MAINS
WATER IN
Place the command centre in the
cupboard as closely as possible to
the outlet tap position. Arrange
tubes in the most direct route
between tap outlet and command
centre, to minimise the length of
tubing. The pipe length is limited to
1000 mm.
ON/OFF switch
15
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 6 Command Centre installation, Chilled ambient installation
6.1 HydroChill chilled ambient model
HC45T1228
Clearance
envelope
280mm
50mm
50mm
550mm
VENT
MAINS
WATER IN
CHILLED
OUT
AMBIENT
OUT
6.2 Manifold connections
6.3 Installation arrangements
Connect to
Red 1/4” pipe from tap
Connect to
Mains (Cat 1) Cold water
supply
Connect to
White 1/4” pipe from tap
Connect to
Blue 1/4” pipe from tap
Twin lever
Place the command centre in the
cupboard as closely as possible to
the outlet tap position. Arrange
tubes in the most direct route
between tap outlet and command
centre, to minimise the length of
tubing. The pipe length is limited to
1000 mm.
ON/OFF switch
Mains cold water
isolation valve
(not supplied)
16
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 7 Commissioning
!
Operation
Pull
HydroChill Twin lever - Chilled ambient
• The lever on the right is used for chilled filtered water and the other, on the left, is
used for ambient filtered water.
• Chilled water is obtained by pulling the lever on the right forward, The water is
chilled by a refrigeration unit fitted within the chiller unit.
• Chilled water can be obtained within the rated capacity, for as long as you pull the
lever forward. Ambient water is obtained in the same manner as the chilled water, by
pulling the lever on the left forward, to the horizontal position.
• The levers will self return, and close the tap once finger pressure has been removed.
HydroChill heavy duty - Chilled only
• Chilled water is obtained by pulling the lever on the tap forward. The water is chilled
by a refrigeration unit fitted within the under counter chiller.
• Using the Heavy Duty HydroChill you can obtain chilled water within the rated
capacity for as long as you pull forward the lever. The lever will self return, and close
the tap once finger pressure has been removed.
Pull
7.0 Commissioning
Due to the sanitisation process, residue from the sanitisation liquid might remain in the product, which
requires the products to be flushed with fresh water at installation. So the first few glasses of water may
look soapy with presence of bubbles. As part of the purge process, dispense 10 litres of water from the tap,
then check that the water is clear, and that there are no soapy looking bubbles in the dispensed water.
• All HydroChill model must be sanitised during the commission process, please contact Zip on 03456 005 005 to
book your free commissioning service.
• Do not commission your HydroChill until ready for use.
• Secure all pipes and cables. After the system is correctly installed and connected, turn the incoming mains cold
water supply on then purge the system of air (follow the instruction in the Filter replacement, page 17).
• Check all connections for leaks. Repair as necessary, again turn the incoming mains cold water supply on,
re-purge and then turn on the mains electricity supply.
• The chiller unit takes up to 20 minutes to chill it’s contents to the rated temperature, depending on the ambient
temperature of the water.
• Ensure your HydroChill is sanitised before use.`
• If your HydroChill is left idle before use for water taste and quality reasons any non-use of more than 48 hours,
Zip recommend a system flush be performed. On first use after a period of non-use, run the chilled / ambient
water functions for 60 seconds to flush the filter and system. Not flushing the system may affect water the
quality. If taste or water quality issues persist, a filter change and sanitisation may be required.
17
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Insert filter
Rotate
Insert
Filter replacement
Remove filter
Rotate
Pull
Changing the filter
For safe operation, the filter cartridge should be replaced at least every 6 months, or earlier
if you notice a persistent reduction in water pressure from the tap or an unpleasant taste or
odour in the water.
For safe operation, thoroughly flush the water through after periods of non-use over 12 hours.
Not changing the filters when required may cause the water to become biologically unsafe.
Use only a Zip filter to match the one used in your system product (see Spare parts page 5). The
filter cartridge can be obtained through plumbing suppliers or direct from Zip. The installation
date should be written on the filter cartridge. No special tools or skills are required to install
the filter cartridge.
• Locate the filter in the under-sink cupboard.
• Grasp the filter firmly and twist it horizontally a quarter turn clockwise until it stops.
Some water will drip from the filter head during the replacement process so it is a good
idea to have a bucket and towel handy to catch and mop up any spills.
• Gently ease the cartridge downwards to detach it from the filter head, then pull it out and
discard responsibly. Take care not to tip it up once free as water may spill out.
• Write the date of replacement on the new filter cartridge label.
• Remove the protective plastic cap. The insertion method is the opposite to the removal
method. Align the tabs of the replacement cartridge with the filter head and insert it up into
the filter head.
• Turn the replacement cartridge a quarter turn anti-clockwise until it stops and locks into
position.
• When the filter replacement has been completed purge the system of trapped air by
dispensing water from the tap until it flows without any further spluttering. Run 10 litres of
water through the system to complete the purge.
Air inlet screen
• The HydroChill air inlet screen is located
on the side of the Command Centre.
• The screen needs to be inspected at
least quarterly, cleaned and replaced if
damaged.
• Remove the screen for cleaning by sliding
it forward.
• Rinse off any particles with tap water, then
gently dry with a cloth or towel.
• Slide the screen back into place.
• For best performance the unit should only
be operated with a clean air inlet screen,
correctly fitted in place.
• Maintain at least a 50 mm air gap in front
of the screen at all times.
• Take care not to allow cloths or other
soft materials to accidentally block the air
inlet.
Slide out to remove
18
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Cleaning
• Cleaning of the tap and dispensing outlets must only be undertaken with a clean
sanitised cloth or disposable sanitise wipe, no chemicals should be sprayed onto the tap
at any time
• Never use strong, corrosive or abrasive cleaning materials on the HydroChill tap or
Command Centre. Wipe clean the outer surfaces with a sponge or a soft cloth using
a mild soap and water.
• The air inlet filter on the side of the Command Centre needs to be kept free of dust
and lint to permit free flow of air. See Air inlet screen, page 17.
Service & general maintenance
There are no user serviceable parts but there are dangerous voltages present within the Command Centre.
All service work must only be carried out by a suitably qualified and experienced trades-person.
• Before calling for service, check that both the water and electricity supplies are turned on and functional.
• Call Zip customer service on 0345 6 005 005 for assistance, service, spare parts and enquiries.
• Zip offers a fully inclusive service plan, HydroCare will take care of all routine maintenance and service work,
including filter replacements, sanitisation, electrical safety inspections as well as general maintenance of your
HydroTap, please visit zipwater.co.uk/HydroCare or contact Zip on 0345 6 005 005 for more information.
• The Zip filter should be replaced at least every 12 months, at the rated capacity or sooner if you notice a
persistent reduction in water flow from the tap or an unpleasant taste or odour in the water. As stated on the
filter cartridge.
• For safe operation, thoroughly flush the HydroTap after periods of non-use longer than 48 hours.
• Not changing the filter cartridges when required may affect the water quality.
• Sanitisation should be carried out at all filter changes, at least at intervals of no more than 12 months.
•
Troubleshooting table
Symptom Possible Cause Solution
No water supplied
Mains water not connected or turned on Connect or turn on water supply.
Water pressure regulator failed Contact local Zip Service Provider.
Unit frozen up Contact local Zip Service Provider.
Internal water leak Contact local Zip Service Provider.
Water not chilled
No power Restore power to the unit.
Thermostat faulty or out of calibration. Contact local Zip Service Provider.
Insufficient cooling air flow through the
refrigeration system
Check and clean air inlet screen.
Refrigeration failure Contact local Zip Service Provider.
Rated chilled water capacity has been
exceeded
Allow unit sufficient time to recover.
!
19
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
End of life disposal
The use of this crossed out wheeled bin logo indicates that this product needs to be disposed of
separately to any other household waste.
Within each of the European Union member countries, provisions have been made for the
collection and recycling of unwanted electrical and electronic equipment.
In order to preserve our environment we ask that you dispose of this product correctly.
Please contact Zip customer service for advice on 0345 6 005 005.
Warranty policy
Our goods and services are supplied in accordance with our standard terms and conditions. This policy sets out
the warranty period and exclusions which apply to the HC45 range. This policy is subject to our standard terms and
conditions and should be read in conjunction with those terms, particularly clause 5 of the terms and conditions
Warranty
The warranty period for the HC45 range is 1 year.
Subject to the exclusions set out below and in clause 5 of the terms and conditions, faulty parts and products will
be replaced or repaired free of charge by Zip, its distributor or service provider, where such faults arise during the
applicable warranty period.
Exclusions
1. This policy only applies where:
(I) The product is installed and used strictly in accordance with the terms and conditions and the instructions
supplied with the product; and
(Ii) The failure is not due to accident, misuse, abuse, unsuitable water conditions (including contaminants or
inappropriate water pressure), or to any alteration, modification or repair by any party not expressly nominated by
Zip.
2. This warranty does not cover damage resulting from non-operation of the product or consequential damage to
any other goods, furnishings or property.
3. This warranty does not apply to any consumables. Consequently, no warranty applies to the life of any filtration
cartridge installed within the appliance as cartridge life may vary according to water quality and the rate of water
consumption.
4. Zip residential (for home) products are designed specifically for use in a domestic, residential location.
Inappropriate installations, such as in a commercial environment (including residential care homes or medical
facilities), will invalidate the warranty.
Service Work
Ad hoc repairs by Zip or its approved service providers are covered under Warranty for 30 days in relation to the
original fault only.
If you are a HydroCare Service Plan subscriber please refer to the HydroCare terms and conditions for information
on applicable warranties and warranty periods for HydroCare services.
Registering your purchase
Registering your zip installation on the zip website may help to establish date of installation should it become
necessary to service the appliance under terms of the zip warranty. To register your installation visit
www.zipwater.co.uk/product-registration.
20
Installation instructions & user manual
806143UK V1.00 July 2019 - HydroChill HC45
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Zip Water UK
0345 6 005 005 [email protected].uk
www.zipwater.co.uk
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Zip HydroChill HC45 User manual

Zip
Brand
Zip
Model
HydroChill HC45
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents