Zip HydroChill HC05 User manual

Zip
Brand
Zip
Model
HydroChill HC05
Type
User manual
1
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: [email protected].uk www.zipwater.co.uk
Installation instructions & user manual
Zip
HydroChill
HC05 Floor standing chiller.
Model number:
HC05T128
2
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Table of contents
Important safety instructions ....................................................................................................................2
Warnings and regulatory information .......................................................................................................3
Technical data ...............................................................................................................................................4
Dimensions & positioning .............................................................................................................................4
Spare parts ..................................................................................................................................................... 5
Accessories .................................................................................................................................................... 6
Before installation..........................................................................................................................................6
Installation
Section 1 Water block ....................................................................................................................................7
Section 2 Ventilation .....................................................................................................................................9
Section 3 Tap installation ...............................................................................................................................10
Section 4 HydroChill installation instructions ...............................................................................................11
Section 5 Commissioning ..............................................................................................................................12
Operation ......................................................................................................................................................12
Filter replacement .........................................................................................................................................13
Service ...........................................................................................................................................................14
Cleaning ........................................................................................................................................................14
Maintenance..................................................................................................................................................15
Trouble shooting ...........................................................................................................................................16
End of life disposal & warranty ......................................................................................................................17
Contact details ..............................................................................................................................................20
This manual contains important safety and installation instructions for the HydroChill.
Please read all warnings, installation requirements and installation instructions before
installing the HydroChill system.
Installation
This system must be installed in accordance with water supply byelaws, current IEE regulations and
relevant local authority byelaws.
Electrical o
The appliance must be connected to the supply through an isolating switch with a contact
separation of at least 3mm in all poles and be protected by a suitably rated RCD.
To protect the appliance, an MCB (miniature circuit breaker) or cartridge fuse must be fitted with a
rating suitable for the nominal current of the appliance.
Safety
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
Refrigerant
The Zip HydroChill contains R134a refrigerant under pressure. Maintenance of the refrigeration unit
!
IMPORTANT SAFETY INSTRUCTIONS
3
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
IMPORTANT SAFETY INSTRUCTIONS
must be carried out by an accredited service provider or qualified refrigeration technician.
Qualifications
If the power cable is damaged it must be repaired only by a qualified technician. To avoid hazards,
all installation procedures must be carried out by a suitably qualified tradesperson. The power cable
and power outlet must be in a safe visible position for connection.
Lifting
Take care when lifting. The HydroChill may exceed safe lifting limits. If you feel this is beyond your
personal capabilities, please seek assistance with the lift. The weight of the HydroChill is marked on
the packaging. Do not lift the HydroChill by the front cover or any of its connections. Refer to the
technical specification, see page 4, for the weight of the product.
Airflow
The Zip HydroChill operates within the ambient temperature range 5ºC - 35ºC. Proper air circulation
must be provided. The system will operate satisfactorily only if the recommended air gaps are
provided. See Section 2 'Ventilation', page 9, for correct installation to prevent overheating.
Sanitising
For safe operation, the HydroChill is designed to be installed, commissioned and used within 48
hours.
Should the HydroChill not be required for an extended period of time (48 hours or more), do not fill
and commission it until ready for first use.
The HydroChill must be sanitised during the commission process, please contact the Zip Water
team on 0345 6 005 005 to book your commissioning service.
For water taste and quality reasons any non-use of more than 48 hours, Zip recommend a system
flush be performed.
On first use after a period of non-use, run the chilled water function for 60 seconds to flush the filter
and system.
Not flushing the system may affect water the quality.
WARNINGS AND REGULATORY INFORMATION
Warnings
• The Zip HydroChill
must be earthed. The resistance of the earth connection
from each exposed metal part must be less than 1Ω.
• All installation and service work must be completed by trained and suitably
qualified tradespeople. Faulty operation due to unqualified persons working on
this product, or any other Zip product may void warranty coverage.
• As the installer, it is your responsibility to supply (if necessary) and install all
valves as required by local regulations and relevant standards.
• The HydroChill is rated for 230V 50Hz AC operation.
• Do not remove the cover of the HydroChill under any circumstances without
first isolating the appliance from the power supply.
• Never locate the HydroChill near, or clean with water jets.
• Do not expose the HydroChill
to the elements of nature.
• Due to the process of continuous improvement, Zip reserves the right to
change details mentioned in this manual, without notice.
• Visit www.zipwater.co.uk to ensure you have the latest copy of this document.
!
!
4
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Technical data
Range Model
Dispense
options
Dispense
rating
Power rating
kW
Refrigerant
Dimensions
W x D x H (mm)
Weight
Empty Kg*
HydroChill
HC05T128 Chilled 28 litres/ hr 0.345 R134a 350 x 350 x 915 28.5
• 15mm compression fitting connecting to mains water supply.
• A wholesome water supply is required with minimum water pressure of 0.15 MPa (1.5 bar).
• If the incoming mains cold water supply pressure exceeds 0.7 MPa (7.0 bar) a pressure reducing valve is required
to be fitted in the supply line. (See Accessories, page 6).
• Water supply temperature range 10 - 38
0
C
• Power Supply: 230V 50Hz AC, 13A.
• Chiller type. Fan cooled condenser with compressor. Operating temperature range 5ºC - 35ºC.
• Refrigerant type: Non-toxic R134a.
• Tap: Chrome plated brass, lever action, vented with swivel head.
• Filtration type: 3 micron filtration.
* Weight is chiller unit only with no accessories
915mm nominal
350mm
520mm nom.
770mm
169mm
12 - 25mm
Drain
Inlet
58mm
1/2” BSP female
cold inlet
Electrical
connection
350mm
Dimensions & positioning
5
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Range Model
Dispense
options
Dispense
rating
Power rating
kW
Refrigerant
Dimensions
W x D x H (mm)
Weight
Empty Kg*
HydroChill
HC05T128 Chilled 28 litres/ hr 0.345 R134a 350 x 350 x 915 28.5
Spare parts
Item Part Description
4 SP7036 Thermostat Chillers
5 95126 Leak Detector
6 95127 Leak Detector Pads
7 SP90019 Fan Motor Kit
8 95132 Relay Compressor AE4430Y-GS1A 50/60
9 95133 Capacitor Compressor Tecumseh AE4430Y-GS1A
10 95134 Overload Compressor Tecumseh AE4430Y-GS1A
11 94441 Compressor Tecumseh AE4430Y-GS1A
12 95130 Pressure Relief Valve
13 SP91552 1/2” BSP - 1/4” JG Adaptor
14 91482 500 KPa Pressure Limit Valve
15 95138 JG Fittings Kit CM/EM/SM
18 SP99249 Vented Carafe Tap HD Self Return (3 Hoses)
19 95131 Evaporator S/S
20 94361 Filter Head & Brk Front
21 93703UK Filter
22 SP91487 Inlet Bush Assy
6
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Item Part No. Description
Optional ZG500* BREEAM installation kit
Optional ZI001 Drinking bubbler
Optional HE45004 Water block (water shut down system)
Optional ZD003 Waste water dish
Optional ZE001 Disposable cup dispenser
AQ3 Pressure reducing valve (3.5 bar)
* The Optional ZG500 Installation kit allows the HydroChill to be installed
fully in accordance with the requirements of BREEAM Health & Wellbeing
Credit HEA 16 (Drinking Water) by enabling the HydroChill to be securely
attached to both the wall and the floor as well as providing security covers to
protect the water and electrical connections.
ZG500 BREEAM Kit
Accessories
Before installation
Before installation ensure that the following have been provided at the
installation site
•
Review of all the technical specifications.
•
Ensure the floor can support the product weight when full of water (allow an extra
4kg when full).
•
For Zip HydroChill floor standing models, 1 x 230V AC 13A socket will be required.
•
The HydroChill must be installed in accordance with IEE regulations, See
Technical specification, page 4 for power ratings.
Note Check all cable and hose lengths against inlet /outlet positions before
proceeding (see pages 4,9 & 11 for general layout).
•
A wholesome water supply connection with a minimum working pressure of: (see
page 4 min. / max. water supply pressure) with isolating valve within reach of the
braided hoses and positioned so that the connection point and the stop cock will
not be obstructed when the HydroChill is installed.
•
If pressure is likely to exceed 0.7 MPa (7 bar), install a 0.35 MPa (3.5 bar) pressure
reducing valve.
•
The HydroChill must be placed with its base in a horizontal position.
IMPORTANT!
Do not proceed with the installation if these requirements are not met.
!
!
7
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
1.0 Description
• The Water Block is designed to be installed upstream of any Zip product and associated pipe-
work to minimise the potential for water leakage in the event of a system malfunction.
• The Water Block is ideal for limiting potential leakage and resulting water damage from water
heaters, water chillers etc. when fitted in supply pipe work that is subject to mains water pressure.
• Once set, the Water Block will ensure that the volume of water that can flow through at one time
is limited to a pre-determined maximum, providing the flow rate through it exceeds 2 litres per
minute.
• The Water Block also incorporates a non-return valve.
• The Water Block is WRAS approved.
1.1 Precautions
• The Water Block will help to contain leakage exceeding a rate of 2 l/min.
• Note The leakage at lower flow rates may not be detected by the Water Block and could remain
unchecked.
• Appropriate measures should be taken to contain leakage in these circumstances.
Specification
Flow control range 5 - 50 litres
Minimum / Maximum pressure 0.2 - 10.0 bar
Maximum ambient
temperature
40ºC
Maximum water temperature 70ºC
Minimum operating flow rate 1.5 +/- 0.5 litres / min.
Inlet connection ¾" BSP female or 15mm
Outlet connection ¾" BSP male or 15mm
!
Installation - Section 1 Water block (optional)
8
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Note. This device must be installed vertically with the direction of flow
downwards (inlet at the top , outlet at the bottom. See Fig 1 adjacent).
• The Water Block should be installed in a convenient location on the water
supply line to the Zip product.
• Pointer ‘P’ (see Fig.3) should be rotated until in line with the maximum required flow at
one time. Each number on the scale corresponds to 5 litres of flow i.e. 1 = 5 litres, 10 = 50
litres.
• The adjustment key (see Fig.2) should be used to adjust the pointer.
• The inlet should be connected via an 15mm isolation valve (not supplied).
• The outlet shall be connected via the 15mm - 1/2” brass compression fitting supplied.
• Ensure that the direction of flow through the Water Block is correct and that the filter
screen (see Fig.2) is inserted correctly with the convex surface facing towards the water
supply.
1.2 Installation
Fig. 2
Fit key to adjust flow
Key
Reset lever
1.3 Reset Procedure
• The Water Block will activate and shut off the supply if more water than the set amount is drawn off at one time.
• In this event firstly isolate and de-pressurise the water supply to the Water Block, identify and repair the cause of
the leak then remove the pipe-work downstream of the Water Block and press the reset button ‘H’ (see Fig.3).
• The reset device (see Fig.2) may be fitted to avoid disconnection. This allows the Water Block to be reset by
operating the lever in the direction shown in Fig.2.
• In the event of persistent tripping contact Zip for advice on 0345 6 005 005.
1.4 Maintenance
• The filter screen should be checked and cleaned periodically subject to water conditions and usage.
Fig. 1
Fig. 3
Direction of flow
Seal
Reset
device
Direction of
flow
Filter
screen
Isolation valve
(not supplied)
15mm - 1/2” brass
compression fitting
Installation - Section 1 Water block
!
9
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 2 Ventilation
50mm back
clearance
50mm RHS side
clearance
300mm LHS
side clearance
400mm
2.0 Clearance envelope
For safe and efficient operation of the HydroChill, the following ventilation clearance envelope must be observed.
10
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 3 Tap installation
Heavy duty
3.0 Configure the heavy duty tap
• The tap base is ready attached to the HydroChill.
• To fit the spout, unscrew the grub screw at the back
of the tap base , in order that it does not foul the
o-rings & bearing on the tap spout.
• Lubricate the o-rings on the tap spout with water.
• Align spout & base, & carefully press the tap spout
into position until the top of the spout base is flush
with the top of the tap base.
• Check that the spout rotates.
• Tighten the grub screw to secure in place (do not
over tighten).
• Rotate the spout to the desired position.
Allen key
Grub screw
Tap spout
Tap base
o -rings
Bearing
Disassembled Assembled
11
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 4 HydroChill installation
4.0 installation instructions,
floor standing HydroChill
Read these instructions before commencing HydroChill installation, they
apply to all installation arrangements.
Connect to
HydroChill
!
• Install the mains water pipework before locating the HydroChill in place. (See diagram below).
• Electrical power cable is 1.6m long.
• The HydroChill
must be installed within the limits of the
pipework and power cable length supplied.
• • Isolation valves are not supplied.Isolation valves are not supplied.
4.1 Connect the water supply and waste pipe4.1 Connect the water supply and waste pipe
• It is the installer’s responsibility to ensure the installation
complies with local water authority regulations and relevant
standards.
• Connect a cold water supply to the 1/2” BSP male inlet at the
back of the unit. See adjacent diagram and, ‘dimensions and
positioning’ , page 4).
• Connect a drain to the 40 mm PVC outlet at the back of the
HydroChill.
4.2 Connect the mains electricity supply4.2 Connect the mains electricity supply
• The HydroChill is supplied with an integral mains power cable
and plug.
• Connect the plug to a 230V AC 13A socket.
• DO NOT SWITCH ON THE ELECTRICITY SUPPLY until
the HydroChill has been filled with water, see Section 5
Commissioning.
Mains cold
water supply
Water block
(optional)
Isolation valve
!
12
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Installation - Section 5 Commissioning
5.0 Commissioning
Once your system is installed it is recommended that during the commissioning process it is sanitised to
the current guidelines before first use. Zip HydroChill models have a free commissioning service please
contact us on 0345 6 005 005 to book your visit.
• Secure all pipes and cables. After the system is correctly installed and connected, turn the incoming mains cold
water supply on then purge the system of air (follow the instruction in the Filter replacement, page 13).
Due to the factory sanitisation process, residue from the sanitisation liquid might remain in the product, which
requires the products to be flushed with fresh water at installation. So the first few glasses of water may look soapy
with presence of bubbles. As part of the purge process, dispense 10 litres of water from the tap, then check that the
water is clear, and that there are no soapy looking bubbles in the dispensed water.
• Check all connections for leaks. Repair as necessary, again turn the incoming mains cold water supply on,
re-purge and then turn on the mains electricity supply.
• The chiller unit takes up to 20 minutes to chill it’s contents to the rated temperature, depending on the ambient
temperature of the water.
!
Operation
HydroChill heavy duty - Chilled only
• Chilled water is obtained by pulling the lever on the tap forward. The water is chilled
by a refrigeration unit fitted within the under counter chiller.
• Using the Heavy Duty tap chilled water within the rated capacity can be dispensed for
as long as the lever is pulled forward.
• The lever will self return, and close the tap once finger pressure has been removed.
Pull
Bubbler (optional)
• Chilled water is dispensed momentarily by pressing the bubbler button.
• Water will stop flowing once the button is released.
Press
Filter timer indicator
• The HydroChill incorporates a filter timer module including a micro-controller-programmable, extended
duration timer. It is programmable from one to six months in duration.
• A red Light Emitting Diode (LED) that shows through the front label will flash once per second when the
selected filter time has elapsed, as a reminder to replace the filter. The unit will stay in this state until the
batteries are exhausted. (To replace the batteries , & reset the timer, see ‘Filter timer module’, page 14).
13
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Insert filter
Rotate
Insert
Filter replacement
Remove filter
Rotate
Pull
• For safe operation, the filter cartridge should be replaced at least every 6 months,
or earlier if you notice a persistent reduction in water pressure from the tap or an
unpleasant taste or odour in the water.
• For safe operation, thoroughly flush the water through after periods of non-use
longer than 12 hours.
• Not changing the filter cartridges when required may cause the water to become
biologically unsafe.
• Use only a Zip filter to match the one used in your chiller product (see Spare parts
page 5). The filter cartridge can be obtained directly from Zip, visit www. zipwater.
co.uk or alternatively call Zip on 0345 6 005 005.
The filter is located behind the front access panel on the HydroChill. The installation
date should be written on the filter cartridge. No special tools or skills are required
to install the filter cartridge.
• Disconnect the mains electricity supply.
• Unscrew the front panel (2 screws at bottom of panel) & lift out to locate the filter.
• Grasp the filter cartridge firmly and twist it horizontally a quarter turn clockwise until
it stops.
Some water will drip from the filter head during the replacement process so it is a
good idea to have a bucket and cloth handy to catch and mop up any spills.
• Ensure that the electrical connections do not get wet.
• Gently ease the cartridge downwards to detach it from the filter head, then pull it out
and discard responsibly. Take care not to tip it up once free as water may spill out.
• Write the date of replacement on the new filter cartridge label.
• Remove the protective plastic cap. Insertion method is opposite to removal.
• Align the tabs of the replacement cartridge with the filter head and insert it up into
the filter head.
• Turn the replacement cartridge a quarter turn anti-clockwise until it stops and locks
into position.
• When the filter replacement has been completed, purge the system of trapped air by
dispense water from the tap until it flows without any further spluttering. Run 10 litres
of water through the system to complete the purge.
• Refit the front panel, clean the stainless steel surfaces, wipe dry any water spills.
• Reconnect the mains electricity supply, & wait for the water to cool before drinking.
!
!
14
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Filter Timer Module
• The 2x AAA batteries should be replaced when filter is replaced.
• Disconnect the mains electricity supply.
• To reprogram the filter timer module, first remove the front panel of the HydroChill. The filter timer module is
located inside.
• Remove the batteries and locate the switch bank, mounted on the reverse side to the battery holder of the
timer module’s printed circuit board.
• Referring to the table below, select the appropriate sequence. Set the switches to ON or OFF positions by
moving the switch with a small screwdriver.
• Replace the batteries and the front panel of the HydroChill.
• Reconnect the mains electricity supply.
Note: Factory Setting is 6 months
TIME
MONTHS
SWITCH 1 SWITCH 2 SWITCH 3 SWITCH 4
1 ON OFF OFF OFF
2 OFF ON OFF OFF
3 ON ON OFF OFF
4 OFF OFF ON OFF
5 ON OFF ON OFF
6 OFF ON ON OFF
TEST X X X ON
(X = Any position)
Service
• There are no user serviceable parts but there are dangerous voltages present within the under counter chiller
unit. All service work must only be carried out by a suitably qualified and experienced trades-person.
• Before calling for service, check that both the water and electricity supplies are turned on and functional.
• Call Zip customer service on 0345 6 005 005 for assistance, service, spare parts and enquiries.
Cleaning
• Never use strong, corrosive or abrasive cleaning materials on the HydroChill
• Wipe clean the outer surfaces with a sponge or a soft cloth using a mild soap and
water.
• The louvres on the sides of the HydroChill need to be kept free of dust and lint to
permit free flow of air through the vents.
• They should be checked regularly, at least monthly, and dusted or vacuumed.
!
15
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Condenser
• The condenser should be cleaned at regular 12-monthly intervals, or when
the filter is replaced.
• The condenser is accessed by a removable panel in the side of the external
case. Disconnect power and remove the 4 screws holding the panel in place
, see adjacent diagram.
• Remove the panel and clean the condenser using a soft-bristled brush or
vacuum. Replace the panel and restore power when complete.
Leak Detector
• A Leak Detector is built into the appliance. If activated, water flow will stop.
• Remove the front panel of the appliance to access the leak detector,
located towards the front of the unit at its base. Identify and repair any
leaks. The leak detector pad must then be replaced.
• Open the cover of the leak detector, (see adjacent diagram). Remove the
existing pad and replace with a new pad. Close the cover and check that
water flow has returned.
• Replace the appliance panel.
Maintenance
16
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
• Prior to any fault finding, please ensure all water connections to the HydroChill are sound and that the incoming
water supply is turned on. Ensure that all electrical connections to the HydroChill are secure and that the unit
has had adequate time to cool down.
• Call Zip customer service on 0345 6 005 005 for assistance, service, spare parts and enquiries.
Symptom Possible Cause Solution
No water supplied
Mains water not connected or turned on Connect or turn on water supply.
Water pressure regulator failed Contact local Zip Service Provider.
Unit frozen up Contact local Zip Service Provider.
Internal water leak Contact local Zip Service Provider.
Leak detector activated
Identify and repair any leaks. Replace
leak detector pad. Contact local Zip
Service Provider if required.
Water not chilled
No power Restore power to the unit.
Thermostat faulty or out of calibration. Contact local Zip Service Provider.
Insufficient cooling air flow through the
refrigeration system
Check and clean air inlet screen.
Refrigeration failure Contact local Zip Service Provider.
Rated chilled water capacity has been
exceeded
Allow unit sufficient time to recover.
Poor flow at outlet Blocked filter Replace filter.
Troubleshooting
17
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Our goods and services are supplied in accordance with our standard terms and conditions. This policy sets out
the warranty period and exclusions which apply to the HC05 range. This policy is subject to our standard terms and
conditions and should be read in conjunction with those terms, particularly clause 5 of the terms and conditions
Warranty
The warranty period for the HC05 range is 1 year.
Subject to the exclusions set out below and in clause 5 of the terms and conditions, faulty parts and products will
be replaced or repaired free of charge by Zip, its distributor or service provider, where such faults arise during the
applicable warranty period.
Exclusions
1. This policy only applies where:
(I) The product is installed and used strictly in accordance with the terms and conditions and the instructions
supplied with the product; and
(Ii) The failure is not due to accident, misuse, abuse, unsuitable water conditions (including contaminants or
inappropriate water pressure), or to any alteration, modification or repair by any party not expressly nominated by
Zip.
2. This warranty does not cover damage resulting from non-operation of the product or consequential damage to
any other goods, furnishings or property.
3. This warranty does not apply to any consumables. Consequently, no warranty applies to the life of any filtration
cartridge installed within the appliance as cartridge life may vary according to water quality and the rate of water
consumption.
4. Zip residential (for home) products are designed specifically for use in a domestic, residential location.
Inappropriate installations, such as in a commercial environment (including residential care homes or medical
facilities), will invalidate the warranty.
Service Work
Ad hoc repairs by Zip or its approved service providers are covered under Warranty for 30 days in relation to the
original fault only.
If you are a HydroCare Service Plan subscriber please refer to the HydroCare terms and conditions for information
on applicable warranties and warranty periods for HydroCare services.
Registering your purchase
Registering your zip installation on the zip website may help to establish date of installation should it become
necessary to service the appliance under terms of the zip warranty. To register your installation visit
www.zipwater.co.uk/product-registration.
Warranty policy
End of life disposal
The use of this crossed out wheeled bin logo indicates that this product needs to be disposed of
separately to any other household waste.
Within each of the European Union member countries, provisions have been made for the
collection and recycling of unwanted electrical and electronic equipment.
In order to preserve our environment we ask that you dispose of this product correctly.
Please contact Zip customer service for advice on 0345 6 005 005.
18
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Notes
19
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Notes
20
Installation instructions & user manual
806310UK V1.00 July 2019 - HydroChill HC05
Technical support
Tel: 0345 6 005 005 Email: service@zipindustries.co.uk www.zipwater.co.uk
Zip Water UK
0345 6 005 005 [email protected].uk
www.zipwater.co.uk
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Zip HydroChill HC05 User manual

Zip
Brand
Zip
Model
HydroChill HC05
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents