Pelco Sarix IMP Series Environmental Mini Dome User manual

C3956M-EN (10/13)

Sarix

®

IMP Series

Environmental Mini

Domes

User Manual

2

3

Contents

Important Notices ......................................................................................................................................................................... 5

Regulatory Notices .............................................................................................................................................................. 5

Radio and Television Interference ....................................................................................................................................... 5

Legal Notice ......................................................................................................................................................................... 5

Video Quality Caution .......................................................................................................................................................... 5

Frame Rate Notice Regarding User Selected Options ........................................................................................................ 5

Open Source Software ........................................................................................................................................................ 6

CCC Power Cord Statement ................................................................................................................................................ 6

KCC Certification ................................................................................................................................................................. 6

Korean Class A EMC .................................................................................................................................................. 6

Korean Class B EMC .................................................................................................................................................. 6

ESD Warning ....................................................................................................................................................................... 6

Network Topology Statement ....................................................................................................................................................... 6

Legal Notice (Audio Notice) .......................................................................................................................................................... 6

Preface ......................................................................................................................................................................................... 7

1. Product Overview .............................................................................................................................................................. 8

1.1 Dimensions .................................................................................................................................................................... 8

1.2 Physical Characteristics ................................................................................................................................................. 9

2. Installation and Connection ........................................................................................................................................ 10

2.1 Unpacking Everything .................................................................................................................................................. 10

2.2 Optional Accessories ................................................................................................................................................... 10

2.3 Installation .................................................................................................................................................................... 10

2.3.1 Checking Appearance ...................................................................................................................................... 10

Disassembling the Camera ....................................................................................................................................... 11

2.3.3 Connecting the Wires ....................................................................................................................................... 11

2.3.4 Installing the Camera........................................................................................................................................ 11

2.3.5 Positioning the Camera .................................................................................................................................... 16

2.3.6 Adjusting the Focus .......................................................................................................................................... 16

4

2.3.7 Network Topology ............................................................................................................................................ 17

2.3.8 System Requirements ...................................................................................................................................... 17

2.4 Connection ................................................................................................................................................................... 19

2.4.1 Default IP address ............................................................................................................................................ 19

2.4.2 Connecting from a computer & Viewing Preparation ........................................................................................ 19

3. Administration and Configuration .............................................................................................................................. 21

3.1 Live .............................................................................................................................................................................. 21

3.2 Settings ........................................................................................................................................................................ 22

3.2.1 System ............................................................................................................................................................. 22

3.2.2 Network ............................................................................................................................................................ 25

3.2.3 Imaging ............................................................................................................................................................. 33

3.2.4 A/V Streams ..................................................................................................................................................... 39

3.2.5 Users ................................................................................................................................................................ 44

3.2.6 Events .............................................................................................................................................................. 47

Technical Specifications ................................................................................................................................................... 57

Pelco Troubleshooting Contact Information ............................................................................................................................... 60

Note for Dimension Drawings ..................................................................................................................................................... 60

5

Important Notices

REGULATORY NOTICES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC

rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority

to operate this equipment under Federal Communications Commission’s rules.

In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with

non-approved equipment or unshielded cables is likely to result in interference to radio and television reception.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

LEGAL NOTICE

SOME PELCO EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL AND RECORDING

CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO CIVIL AND CRIMINAL PENALTIES.

APPLICABLE LAWS REGARDING THE USE OF SUCH CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY

REQUIRE, AMONG OTHER THINGS, EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU ARE SOLELY

RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT ADHERENCE TO ANY/ALL

RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS EQUIPMENT AND/OR SOFTWARE FOR ILLEGAL

SURVEILLANCE OR MONITORING SHALL BE DEEMED UNAUTHORIZED USE IN VIOLATION OF THE END USER

SOFTWARE AGREEMENT AND RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS

THEREUNDER.

VIDEO QUALITY CAUTION

FRAME RATE NOTICE REGARDING USER SELECTED OPTIONS

Pelco systems are capable of providing high quality video for both live viewing and playback. However, the systems can be

used in lower quality modes, which can degrade picture quality, to allow for a slower rate of data transfer and to reduce the

amount of video data stored. The picture quality can be degraded by either lowering the resolution, reducing the picture rate,

or both. A picture degraded by having a reduced resolution may result in an image that is less clear or even indiscernible. A

picture degraded by reducing the picture rate has fewer frames per second, which can result in images that appear to jump or

move more quickly than normal during playback. Lower frame rates may result in a key event not being recorded by the

system.

Judgment as to the suitability of the products for users' purposes is solely the users' responsibility. Users shall determine the

suitability of the products for their own intended application, picture rate and picture quality. In the event users intend to use

the video for evidentiary purposes in a judicial proceeding or otherwise, users should consult with their attorney regarding any

particular requirements for such use.

6

OPEN SOURCE SOFTWARE

This product includes certain open source or other software originated from third parties that is subject to the GNU General

Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses,

disclaimers, and notices.

The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer to the exact terms

of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or http://www.opensource.org (Open Source Initiative)

regarding your rights under said license. You may obtain a complete corresponding machine-readable copy of the source code

of such software under the GPL or LGPL by sending your request to digitalsupport@pelco.com; the subject line should read

Source Code Request. You will then receive an email with a link for you to download the source code.

This offer is valid for a period of three (3) years from the date of the distribution of this product by Pelco.

CCC POWER CORD STATEMENT

Models shipped to China do not include power cords.

NOTE: A CCC approved power cord must be used to power the equipment when used in China.

KCC CERTIFICATION

Korean Class A EMC

Korean Class B EMC

ESD WARNING

WARNING: This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to this product,

use ESD safe practices during installation. Before touching, adjusting or handling this product, correctly attach

an ESD wrist strap to your wrist and appropriately discharge your body and tools. For more information about

ESD control and safe handling practices of electronics, please refer to ANSI/ESD S20.20-1999 or contact the

Electrostatic Discharge Association (www.esda.org).

Network Topology Statement

IMPORTANT NOTE. PLEASE READ. The network implementation is shown as a general representation only and is not

intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network

equipment to accommodate the system as illustrated. Please contact your local Pelco Representative to discuss your specific

requirements.

Legal Notice (Audio Notice)

NOTE: Improper use of audio/visual recording equipment may subject you to civil and criminal penalties. Applicable laws

regarding the use of such capabilities vary between jurisdictions and may require, among other things, express written consent

from the recorded subjects. You are solely responsible for insuring strict compliance with such laws and for strict adherence to

any/all right of privacy and personality.

WARRANTY STATEMENT

For information about Pelco's product warranty and thereto related information, refer to

www.pelco.com/warranty.

7

Preface

This user manual is to be used as a reference for the installation and manipulation of the camera unit including features,

functions, and a detailed explanation of the menu tree.

This manual provides the reader with the following information:.

• Product Overview: the main functions and system requirements of the unit

• Installation and Connection: instructions on unit installation and wire connections

• Administration and Configuration: the main menu navigation and controls explanations

8

1. Product Overview

1.1 Dimensions

The Sarix Series network dome camera has three installation methods (refer to 2.3.4 Installing the Camera on page 14).

Figure 1-1 depicts the dimensions of the environmental mini dome, as well as the dimensions of three backbox configurations

(pendant mount, ceiling mount, surface mount).

ENVIRONMENTAL DOME ENVIRONMENTAL DOME IN ENVIRONMENTAL PENDANT MOUNT

ENVIRONMENTAL DOME IN ENVIRONMENTAL CEILING MOUNT ENVIRONMENTAL DOME IN ENVIRONMENTAL SURFACE MOUNT

FIGURE 1-1: PHYSICAL DIMENSIONS

9

1.2 Physical Characteristics

①

②

③

①

④

⑤

⑥

FIGURE 1-2: CAMERA CONNECTIONS AND FEATURES 1/2

④

⑦

⑧

⑨

F

IGURE 1-3: CAMERA CONNECTIONS AND FEATURES 2/2

1. Network Cable: Connect the network cable, pass the cable through the cable hole and fix it to the cable slot as the figure

shows.

2. 24 VAC Power: Supports 24 VAC as the power source.

3. Audio In, Alarm In/ Out

 Audio In: Connect to device that responds to audio signals.

 Alarm In/ Out: Connect to device that responds to alarm signals.

4. RJ-45 Network Port: Connects the camera to the IP network. Also supplies power to the camera through the network

using PoE. If PoE is not available, the camera is prewired for 24 VAC.

5. Dome Liner

6. Lens

7. Default: Using a small tool, such as a paper clip, hold down the reset button longer than 5 seconds to reset the camera to

factory defaults.

8. Micro-SD Card: To record images when events happen.

9. Reset: Using a small tool, such as a paper clip, press the reset button briefly and release to restart the camera.

10

2. Installation and Connection

2.1 Unpacking Everything

Check that all items in the packing box against the order form and the packing slip. In addition to this manual, the items below

are included in the packing box:

 One Mini Environmental Dome Camera

 One CD containing the DU2.2, User Manual, Specifications

 One printed Quick Installation Guide

 One Terminal header 2P

 One Terminal header 8P

 One Wrench pin torx

Please contact your dealer if any items are missing.

2.2 Optional Accessories

 IMPBB-ES: a Sarix Environmental Surface Mount for Mini Environmental Dome White

 IMPBB-EP: a Sarix Environmental Pendant Mount for Mini Environmental Dome White

 IMPBB-EI: a Sarix Environmental In-Ceiling Mount for Mini Environmental Dome

2.3 Installation

Following tools might help you complete the installation:

 a drill

 screwdrivers

 wire cutters

2.3.1 Checking Appearance

Although the protective materials used for the packaging should be able to protect the unit from most accidents during

transportation, check the unit and its accessories for any visible damage. Remove the protective film to check items in

accordance with the list in 2.1 Unpacking Everything.

11

Disassembling the Camera

Before you mount and adjust the camera, push and remove the dome cover (#2) with caution.

①

②

F

IGURE 2-1: DISASSEMBLING THE CAMERA

2.3.3 Connecting the Wires

This unit supports one of the following options as power supply.

 24 VAC: Connect 24V (~) cables to terminals ~24 VAC

 PoE: Connect the RJ-45 network connector to a PoE compatible network device that has supplied power through the

Ethernet cable.

 (Optional) Insert audio cable and alarm cable to the unit, and connect the network cable to the RJ-45 network port of

a switch. Refer to Network Cable in 1.2 Physical Characteristics to manage the cables.

NOTE: To avoid the length deficiency, you should reserve about 10mm length of the network cable for connecting the

cable to the RJ-45 network port before attaching the cable to the cable slot.

F

IGURE 2-2: CONNECTING THE NETWORK CABLE

2.3.4 Installing the Camera

You can install the Sarix Series dome camera using one of the following installation methods:

 Surface Mount (refer to 2.3.4.1 Surface Installation)

 Pendant Mount (refer to 2.3.4.2 Pendant Installation)

 In-Ceiling Mount (refer to 2.3.4.3 In-Ceiling Installation)

①

Camera Body

②

Dome Cover

12

2.3.4.1 Surface Installation

Surface Installation involves mounting the camera to the wall with the IMPBB-ES Sarix Environmental Surface Mount for

Mini Environmental Dome White.

1. Pass all cables through the back box cable hole and attach the camera body (#2) to the back box (#1).

2. Attach the guide pattern that is used for surface mount to the wall or ceiling.

T1: Doubl e gang

T2: Si ngl e gang

T3: Pe l co I M- VE Mount

T4: 4” Square b ox

T5: Pe l co I M Mount

145mm ( 5. 7" )

I nner 3. 3(

0. 125i nch) Hol es

( M4 or #6 TYPE SCREW )

Out er

6

( 0. 25i nch) Hol e s

( FOR PLASTI C ANCHOR )

FIGURE 2-3: ATTACHING THE GUIDE PATTERN

3. According to the guide pattern (#1), drill a bottom conduit hole or side conduit hole and pull the wires through the hole.

4. Attach the mount plate (#2) of surface mount back plate to the mounting surface with proper screws.

5. Secure the back box (#3) to the mounting surface with three captive screws.

6. Position the camera as needed (refer to 2.3.5 Positioning the Camera on page 18).

7. Focus the lens (refer to 2.3.6 Adjusting the Focus on page 18).

8. Install the dome cover (#5) and complete the installation.

13

①

②

③

④

⑤

FIGURE 2-4: SURFACE INSTALLATION

2.3.4.2 Pendant Installation

The Pendant Installation involves mounting the camera to the wall with the IMPBB-EP Sarix Environmental Pendant

Mount for Mini Environmental Dome White. To attach the camera into the back box, it must be installed with a rain-tight

compression connector and a lock nut as shown in Figure 2-5 are both provided.

①

②

F

IGURE 2-5: RAIN-TIGHT& LOCK NUT

Refer to Figure 2-6 for pendant installation.

1. Pass all cables through the pendant pipe cable hole. Use mounting screws appropriate to your installation.

2. Screw the rain-tight compression connector onto the pipe until tight. Slide the back box (#1) onto the pipe until it rests on

the underside of the rain-tight compression connector.

3. Screw the lock nut onto the pipe protruding from beneath the back box. Tighten until the back box is held firmly in place.

4. Mount the camera body (#2) to the back box (#1).

①

Guide Pattern

② Mount Plate

③ Back Box

④ Camera Body

⑤ Dome Cover

①

Rain-tight Compression Connector

② Lock Nut

14

5. Use screws to attach the back box to the mounting surface.

6. Position the camera as needed (refer to 2.3.5 Positioning the Camera).

7. Focus the lens (refer to 2.3.6 Adjusting the Focus).

8. Install the dome cover (#3) and complete the installation.

①

②

③

F

IGURE 2-6: PENDANT INSTALLATION

2.3.4.3 In-Ceiling Installation

The In-Ceiling Installation involves mounting the camera into the ceiling with the IMPBB-EI Sarix Environmental In-Ceiling

Mount for Mini Environmental Dome.

1. Attach the guide pattern used for in-ceiling mount to the wall or ceiling.

mm ( 5.

3" )134

( Backbox)

mm ( 5. 7

" )145

F

IGURE 2-7: ATTACHING THE GUIDE PATTERN

①

Back Box

② Camera Body

③ Dome Cover

15

2. According the guide pattern, cut a hole in the ceiling/wall.

3. Insert the back box into the hole and screw the two screws with a screwdriver so the antidropping claspers can slide out to

chuck the back box into the ceiling (refer to Figure2-8 & Figure2-9).

①

F

IGURE 2-8: INSERTING THE BACK BOX

④

F

IGURE 2-9: CHUCKING THE BACK BOX

4. Pass all cables through the back box cable hole and attach the camera body (#2) to the back box (#1).

5. Position the camera as needed (refer to 2.3.5 Positioning the Camera).

6. Focus the lens (refer to 2.3.6 Adjusting the Focus).

7. Install the dome cover (#3) and complete the installation.

16

①

②

③

FIGURE 2-10: IN-CEILING INSTALLATION

2.3.5 Positioning the Camera

1. Retract the dome liner.

2. View the camera image using the browser (refer to 2.4 Connection on page 20).

3. Use a small Phillips-head screwdriver to loose the screw (#5) for tilt adjustment.

4. Manually rotate and tilt the camera module to position the camera. Do not over-rotate the module.

WARNING: Excessively turning the module in one direction could result in damage to the wiring.

①

②

③

④

⑤

F

IGURE 2-12: POSITIONING THE CAMERA

2.3.6 Adjusting the Focus

1. View the camera image using the browser (refer to 2.4 Connection on page 20).

① Back Box

② Camera Body

① Pan = 355°

② Rotate = 360°

③ Tilt = 90°

④ Dome liner =90°

17

2. Use the settings in the Web interface (refer to 3.2.3.3 Focus on page 37) to adjust the zoom and focus of the lens to the

desired field of view.

3. Also the focus can be adjusted by moving the zoom slider and using the Focus options in the live webpage.

NOTE: Focus adjustment is done exclusively with Web UI.

2.3.7 Network Topology

The camera can deliver video images and audio in real time using the Internet and Intranet. It's equipped with Ethernet RJ-45

network interface.

FIGURE 2-13: NETWORK TOPOLOGY TYPE

Ⅰ

FIGURE 2-14: NETWORK TOPOLOGY TYPE

Ⅱ

2.3.8 System Requirements

Below table lists the minimum requirement to implement and operate a unit. Network and processor bandwidth limitations

might cause the video stream to pause or appear pixilated when additional Web-interface users connect to the camera.

Decrease the images per second (ips), resolution, compression, or bit rate settings of the Web interface video streams to

compensate for network/processor limitations.

T

ABLE 2-1: SYSTEM REQUIREMENTS

System Hardware

CPU

Intel® Pentium® 4 microprocessor, 2.4GHz or equivalent

RAM

1 GB or above

Monitor

Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution

System Software

Operating System

Microsoft Windows XP, Vista 32 and 64 bit, Win7 32 and 64 bit

Browser

Microsoft IE 8.0 and later

Media Player Pelco Media Player or QuickTime® 7.6.5 for Windows XP, Windows Vista, and Windows 7; or

QuickTime 7.6.4 for Mac OS X 10.4 (or later)

Unit

Power Supply

AC 24V / PoE

18

Note

1. All the installation and operations should comply with your local electricity safety rules.

2. Pelco Media Player is recommended for control, smoothness, and reduced latency as compared to

QuickTime. The PMP is downloadable from Pelco web site: www.pelco.com/mediaplayer.

3. This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If

you have this version installed on your PC, you will need to upgrade to QuickTime version 7.6.5.

4. Network and processor bandwidth limitations might cause the video stream to pause or appear

pixelated when additional Web-interface users connect to the camera. Decrease the images per

second (ips), resolution, compression, or bit rate settings of the Web interface video streams to

compensate for network or processor limitations.

Caution

To avoid damage to the unit, never connect more than one type of power supply (PoE IEEE802.3

Ethernet Class 3 or AC 24V power plug) at the same time.

19

2.4 Connection

2.4.1 Default IP address

The unit’s default IP address is 192.168.0.20 and sub mask is 255.255.255.0. When setting default IP address of 192.168.0.20

the camera will check to see if that address is already in use and will bump the last octet of the address by 1 if it is. The bump

last octet of IP Address by 1 will continue until an unused IP address is found.

However, if you have a DHCP server in your network, the unit would obtain an IP address automatically from the DHCP server

so that you don’t need to change the camera’s IP address. The factory default is DHCP On and 192.168.0.20 assignment only

occurs when camera is set for DHCP but a DHCP server does not respond to request for an IP address.

2.4.2 Connecting from a computer & Viewing Preparation

2.4.2.1 Using Pelco Device Utility 2.2 Software to Get Camera’s IP Address

Pelco Device Utility 2.2 software is a utility program that helps users to manage and configure the camera. Use the utility to

find the IP address since the default option is to obtain an IP address via DHCP and therefore the IP address will NOT be

known. Steps to get the utility program running are listed below.

1. According the installation instructions to finish installing the Device Utility 2.2 to the computer.

2. Log in to the Device Utility by entering the camera’s User name and Password. In the window, enter the default user

name: admin and password: admin, then click Enter DU2 button to log in.

3. In the Manage Devices page, you can click Refresh Device List or Add New Device to search for the devices.

4. From the Device List, you can get series information about camera, IP Address included.

For more information about using DU2, click this green icon "

" on the upper-right corner of the Device Utility 2 page to get

the Device_ Utility_ 2_Help.

2.4.2.2 Connecting from a computer

1. Check whether if the networking available between the unit and the computer by executing ping the default IP address.

Start a command prompt (Windows: from the Start Menu, select Program. Select Accessories and choose Command

Prompt.), and type “Ping 192.168.0.20”. If the message “Reply from…” appears, it means the connection is available.

2. Start Internet Explorer and enter IP address: 192.168.0.20. A login window should pop up. In the window, enter the

default user name: admin and password: admin to log in.

NOTE: If you do not know the camera’s IP address, you can locate it using the Pelco Device Utility 2.2 software (refer to

2.4.2.1 Using Pelco Device Utility 2.2 Software to Get Camera’s IP Address on page 20).

Further administration on the unit can be found in “3. Administration and Configuration".

F

IGURE 2-15: LOGIN WINDOW

20

2.4.2.3 Viewing Preparation

Images of the unit can be viewed through Microsoft Internet Explorer 8 or later. Before viewing, follow these steps to enable

the display.

1. Enable Cookies On the Privacy tab, move the settings slider to Low or Accept All Cookies.

2. Change Security in Internet options and click Custom Level to open the Security Settings – Internet Zone screen.

NOTE: If the camera operates inside of the intranet, click the Intranet icon. If the camera operates outside of the intranet,

click the Internet icon.

3. Scroll down to the ActiveX controls and plug-ins radio buttons and set as follows:



【

Download signed ActiveX controls

】

 Prompt (recommended)



【

Download unsigned ActiveX controls

】

 Prompt



【

Automatic prompting for ActiveX controls

】

Enable



【

Run ActiveX controls and plug-ins

】

 Enable



【

Script ActiveX controls marked safe for scripting*

】

 Enable

4. Press OK to save the settings.

5. Close all Microsoft Internet Explorer Windows and restart a new window. This will allow the new settings taking effect.

6. Type your setting IP address into the browser.

7. Then you should be able to see the camera image screen.

Page is loading ...

Pelco Sarix IMP Series Environmental Mini Dome User manual

Pelco Sarix IMP Series Environmental Mini Dome User manual

Related papers

Other documents