2. JABSCO
  3. 37275 Series

JABSCO 37275 Series User manual

  • Hello! I am an AI chatbot trained to assist you with the JABSCO 37275 Series User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
1
DESIGNER STYLED MARINE
TOILET
FEATURES
• Veryquietflushcycle -likeahouseholdtoilet
• Singlebuttonflushactuator-withdualfunctionwater
levelcontrolswitch
• SuppliedwithPar-Max4self-primingpumpto
provideseawaterorlakewatertorinsethetoilet
bowl
• Vitreouschinabowlavailableincompact14"height
orstandard17"height
• AvailableinWhiteorBone
• Bakedenamelseat&cover
• Highcapacitywastemaceratorandbowldischarge
pump
• Alltoiletplumbingandwiringconnectionsare
internal-outofsight
SPECIFICATIONS
Ports: PAR-MAXPumpandToilet
Inlet-3/4"HoseBarb
Outlet-1"HoseBarb
Motor & Switch: PumpandToiletMeetU.S.C.G.
Regulation183.410andISO
8846MarineforIgnition
Protection.
Toiletsaremarked
andcomply with 
EN50081-1forsuppressionof
electro-magneticinterference.
Normal Water 
Consumption: 1-2Quarts(Litres)/Flush
OPERATION
The Designer Styled Toilets with the popular Quiet-
Flush system provide both quiet operation and user
controlofwaterlevelsinthetoiletbowl.Asinglelarge
push-button switch provides a simple flush mode by
activatingboththerinsewatersupplyandthemacerator
discharge pump simultaneously. An additional rocker
switch offers independent control of the rinse water
supply and discharge pump separately so the bowl
waterlevelcanbeeasilyraisedorloweredbytheuser.
Thisprovidesamethodofminimizingwateruse,when
desired,aswellasameansofraisingthewaterlevelin
the bowl when appropriate for user comfort. It also
allowsforcompleteevacuationofthebowlwaterwhile
underwayinroughseaconditions.
Model Number Description
37275-0092 CompactWhiteToilet14",12VoltEMC
37275-0094 CompactWhiteToilet14",24VoltEMC
37275-1092 StandardWhiteToilet17",12VoltEMC
37275-3092 StandardBoneToilet17",12VoltEMC
37275-1094 StandardWhiteToilet17",24VoltEMC
37275-3094 StandardBoneToilet17",24VoltEMC
INSTALLATION
The 37275-Series Designer Styled Toilet includes the
Quiet-FlushToiletpumpingsystemandissuppliedwitha
dedicatedPAR-MAX4pumptoprovideeitherseaorlake
water to rinse the toilet bowl when flushing the
toilet.Thispumpisintendedtobelocatedremotelyfrom
the toilet but will function best if the distance from the
toiletiskepttoaminimum.Becauseitisself-priming,it
maybelocatedabovethevessel’swaterline.Itmustbe
installedwith the Pumpgard strainer (providedwiththe
toilet) located somewhere in the inlet plumbing to the
pump. The toilet also includes a multi-function flush
controlwhichshouldbeinstalledinabulkheadlocation
that is convenient to the toilet and allows access for
wiringtorunfromthepowersourceandtoboththetoilet
discharge pump and PAR-MAX rinse water pump.
Because all plumbing and wiring connections at the
toilet are made internally within the china bowl, all
plumbingandwiringmustbecompletedandextendedto
thetoiletlocationpriortofinalinstallationofthetoilet.
Model 37275-Series
2
Installthetoiletseatandlidassemblyonthechinabowl
withthefastenersprovidedandpositionthetoiletinits
desiredlocation.Whenlocatingthetoilet,ensurethere
isadequateclearanceabovethebowlsotheseatand
lid assembly can rotate to its fully open position and
remain open on its own. Once the exact position has
been determined, mark the location of the two toilet
mounting holes on the toilet mounting surface and
move the toilet temporarily out of the way. When
securingthetoilettoaplywoodunderlaymentbelowa
layeroffiberglass,toavoidcrackingthefiberglass,drill
a5/16"(8mm)holethroughjustthefiberglasslayerto
provideclearanceforthescrewthreadsandshank.Drill
a3/16"(5mm)pilotholetoacceptthethreadedportion
ofthetoiletholddownscrewsetprovided.Itisgenerally
besttowaituntilthetoiletisreadytobeinstalledforthe
finaltimebeforescrewingtheholddownscrewsintothe
mountingsurface.
The PAR-MAX pump should be mounted to a solid
mounting surface. It should be secured with four
fastenersthroughtherubbergrommetsthatsnapinto
the pump’s base. Do not over-tighten the mounting
screwsandcrushthegrommetssuchthattheywillnot
absorb vibration. The pump may be mounted in any
position;however,ifmountingittoaverticalsurfaceit
shouldbeorientedsowaterdrippingfromalooseport
connection will notdripdownonthemotor. Plumbing
runsshouldbekeptasshortandstraightaspossible.
Allplumbingshouldbecompletedwithquality3/4"(19
mm)hosethatwillnotcollapseorkink.Routetheinlet
hosefroma3/4"(19mm) throughhullandseacock
fittinglocatedwellbelowthewaterline(andwellforward
ofanydischargethroughhulls,ifinstalled)tothepump
inletport.
Ensure the inlet hose passes through an accessible
location(preferablyabovethevessel’swater-line)that
will allow for the installation of the Toilet Pumpgard
strainer where it can be periodically inspected and
cleaned of debris. The Pumpgard strainer should be
securedwithtwofastenerstoasolidmountingsurface
withtheflowarrowpointingtowardsthepump.Theinlet
hose should be cut and each end attached to the
strainer’s ports. Connect the hose from the discharge
portofthestrainertothePAR-MAXpump’sinletport.
Connect another length of hose from the pump’s
dischargeporttotheareaatthebackoftheDesigner
StyledToilet withadequatelengthto connectwiththe
3/4"(19mm)hosebarbatthebackofthechinabowl.
DANGER
!
CAUTION
!
WARNING
!
WARNING
Floodhazard.Iftoiletisinstalledbelowthewaterline
ormaybebelowthewaterlineatanyangleofheelor
trim, it must be intalled with properly positioned
ventedloops.Failuretodosocanresultinflooding
whichcancauselossofpropertyandlife.
Ifthetoiletisinstalledbelowthevessel’swaterline,inorder
topreventasiphonactionfromfillingthetoilet,aproperly
positioned ventedloop fitting must be installed between
thePAR-MAXpumpandthebackofthetoiletbowl.
The vented loop fitting must be secured in a location
thatremainsatleast6-8inches(15-20cm)abovethe
waterlineatallanglesofheelandtrim(seediagram).
Thetoiletdischargeportissizedfor1"(25mm)hose.
Thedischargehoseshouldbeaqualitygradereinforced
hosesuitableforwasteapplications.Routethedischarge
hosetotheholdingtankinthemostdirectwaywithas
fewbendsaspossible.Toretainsomewaterinthebowl,
itisbesttoloopthedischargehoseupabout8-10inches
(15-20cm)asclosetothetoiletaspracticalthenonto
the holding tank. Providing adequate length of hose to
includesuchaloopalsowillprovidetheabilitytomovethe
toiletoutawayfromthebulkheaditbuttsagainsttocomplete
thehoseconnections.Itisbesttoavoidanydipsorlowspots
inthedischargeplumbingthatcanactaswatertrapsand
collectwaste.Ifthisoccurs,wastecansolidifyandcausea
dischargeblockage.
DANGER
!
CAUTION
!
WARNING
!
WARNING
Floodhazard.Iftoiletisinstalledbelowthewaterline
ormaybebelowthewaterlineatanyangleofheelor
trim, it must be intalled with properly positioned
ventedloops.Failuretodosocanresultinflooding
whichcancauselossofpropertyandlife.
Heeled Waterline
Waterline
Vented Loop
Heeled Waterline
Waterline
Vented Loop
3
3
Ifthetoiletisplumbedtoanoverboarddischarge,andis
belowthevessel’swaterline,thedischargeplumbingmust
includeaproperlypositionedventedloop.Theventedloop
fittingmustbe securedin a locationthat remainsatleast
6-8inches(15-20cm)abovethewaterlineatallanglesof
heel and trim. The maximum discharge head without a
notabledecreaseinpumpperformanceisfourfeet(1.3M).
Ensure each hose end is pushed completely onto its
portfittingandsecureeachwithahoseclamp.Allhose
connections made below the waterline should be
secured with two stainless steel clamps. It is best to
securethehosesinplaceabouteveryeighteeninches
alongthelengthoftherun.
Onceallhoseconnectionsarecompletedandsecured
withclamps,itisbesttocompletethewiringsothetoilet
can be tested for leaks prior to fastening it to its
mountingsurface.Oncetheelectricalwiringiscomplete,
testthetoiletbyflushingseveraltimesandblotallhose
termination’scompletelyaroundeachconnectionwitha
whitepapertowelandinspectthetowelforwetspots.If
thetowelcomesawaydryfromeachconnectionwithin
the china bowl, proceed to fasten the toilet to its
mountingsurface.
Positionthetoiletinitsintendedmountingpositionand
verygently,witha10mmwrench,screwtheprovided
toilet hold-down fastener into the pilot hole drilled
earlier.Donotovertightenthesefastenersasthismay
crack the china. It is only necessary to make the
fastenerssnugenoughtopreventthetoiletfromsliding
around. Screw the dress cap into the top of the hold-
downscrew.
ELECTRICAL
Theelectricalwiringshouldbeindependentofallother
accessories. It should be made with marine grade
copper stranded wire of the gauge specified in the
electricalspecificationschart.Makeallwireconnections
with mechanical locking type connectors (crimp type
buttconnectorsandterminals).
Ensurethecircuitisprotectedbyapropersizedfuseor
circuit breaker determined from the electrical
specificationschart.Secureallwirestoasolidsurface
approximatelyeveryeighteeninches(1/2M)alongtheir
entirelengthofrun.
ELECTRICAL SPECIFICATIONS
AMP FUSE WIRE SIZE PER FEET OF RUN*
VOLTAGE DRAW SIZE
0'-10' (0 M-3 M) 10'-15' (3 M-4,6 M) 15'-25' (4,6 M-7,6 M) 25'-40' (7,6 M-12,2 M) 40'-60' (12,2 M-18,3 M)
12Vdc 10 25 #16(1,5mm
2
) #14(2,5mm
2
) #12(4mm
2
) #10(6mm
2
) #8(10mm
2
)
24Vdc 5 15 #16(1,5mm
2
) #16(1,5mm
2
) #16(1,5mm
2
) #14(2,5mm
2
) #12(4mm
2
)
*Lengthofrunistotaldistancefrompowersourcetoproductandbacktoground.
BROWN YELLOW
BROWN
YELLOW
YELLOW
BROWN
RED
RED
RED
RED
TO
POSITIVE
To Waste Pump
Positive
(Orange) Motor
Lead
To PAR-MAX
Pump Positive
(Orange) Motor
Lead
WIRING DIAGRAM TEMPLATE
1-3/4" (45 MM) DIA
1-3/4" (45 MM) DIA
UP
4
DANGER
!
CAUTION
!
WARNING
!
WARNING
Flood hazard. If toilet is plumbed to an overboard
discharge, close the discharge seacock prior to
disassembling toilet. Failure to do so can result in
floodingwhichcancauselossofpropertyandlife.
WiretheswitchpaneltothePAR-MAXrinsepumpand
toiletwastepumpasperthewiringdiagram.Thebrown
lead from the control panel connects with the waste
pump orange (positive) motor lead. The yellow lead
from the control panel connects with the PAR-MAX
rinsewaterpumporange(positive)motorlead.
Theblackmotorleadfromeachpumpmustbeconnectedto
batterynegative.Selectalocationfortheswitchpanelthatis
convenienttothetoiletuserandwillalsoallowaccesstorun
thewiresfromtheswitchpaneltoboththetoilet’swastepump
motorandthePAR-MAXpumpaswellasfromtheelectrical
powersourcetotheswitchpanel.Toinstalltheswitchpanel,
drilltwo1-3/4"(45mm)diameterholes(slightlyover-lapping)
throughtheselectedswitchmountingsurfacepertheattached
template.Ensurethetemplateisorientedcorrectlybecauseit
isnotsymmetrical.Also,drillfourappropriatesizedholesfor
the fasteners selected to secure the switch panel to its
mountingsurface.
WASTE PUMP SERVICE
TheJabscoQuiet-FlushToiletdoesnotrequireroutine
maintenanceotherthanoccasionalcleaningtomaintain
ahygienicsanitarycondition.Cleantoiletwithmildnon-
abrasive cleaners without strong aromatics. Cleaners
havinghigh concentrations of aromatics such as pine
scented concentrated cleaners and strongly scented
degreaserconcentratescan cause the pump’s seal to
swellandmaycontributetoaprematuresealleak.The
toilet has no wearing parts that need periodic
replacement other than the shaft seal which, under
normal conditions, should provide several years of
service before needing replacement. The seal only
requires replacement if signs of leakage are noticed
aroundthebaseandrearofthetoiletchinabowl.
NOTICE: Before performing any service, turn off the
electricalpowertothetoiletandrinsewaterpump.Take
precautiontoensureitisnotturnedonuntiltheservice
is complete. Also, pump all water from the toilet bowl
andifconnectedtoanoverboarddischarge,closethe
dischargeseacock.
To replace the shaft seal, remove the two toilet hold-
down screw caps and remove the hold-down screw
nuts. Carefully lift the toilet up and away from the
bulkhead at it’s rear. Remove the pump assembly by
removingthefourscrewswithlockwashersthatsecure
it to the plastic toilet base. Carefully slide the pump
assemblyfromthebaseensuringthemaceratorhousing
alsoslidesoutofthebasewiththepump.The pump
chopperwillengagethemaceratorhousinganditmay
be necessary to gently tap the chopper against the
maceratorhousingtofreeitfromthebase.
Prevent the motor shaft from turning by inserting a
screwdriverintheshaftslotattherearofthemotorand
removethe self lockingnut.Removethe chopperand
macerator housing from the motor shaft. Remove the
O-ringfromtheO-ringgroovearoundtheouterdiameter
of the seal housing.With an allen wrench, loosen the
centrifugalimpellersetscrewandslidetheimpelleroff
theshaft.Removethetwoscrewsthatsecuretheseal
housingtothemotorandslidethehousingoffthemotor
shaft. Remove the two seal washers from under the
headof eachofthetwosealhousingretainerscrews.
Withapairofneedlenosepliers,grasptheshaftseal
and pull it from the seal housing. Clean all parts and
inspectfordamage.
LubricatetheODofthenewsealwithasmallamount
ofwaterandpressitintothesealborewiththeseal’slip
facingthethreadedendoftheshaft.
Do not use the stain less steel star retaining washer
supplied with the seal.
LubricatetheIDofthesealandthemotorshaftwitha
small amount of water resistant grease. Ensure the
slingerisproperlypositionedonthemotorshaftnextto
the motor and slide the seal housing onto the motor
shaftuntilitisagainstthemotorendbell.Positionanew
plasticseal washerundertheheadofeach of the flat
headsealhousingretainerscrewsandsecuretheseal
housingtothe motor.Slide thecentrifugal impelleron
themotorshaftpositioningitabout1/32"(1mm)from
thesealhousingandsecureittotheshaftwiththeset
screw.Rotatetheimpellertoensureitdoesnotrubon
thesealhousing.
Slidethemaceratorhousingoverthemotorshaft.Place
thechopperontheshaftwiththetabontheflatofthe
shaft.Installtheselflockingnutandtightenfirmlywhile
holdingthemotorshaftattherearofthemotor.Position
anewO-ringinthesealhousingO-ringgroove(itmay
be retained in the groove with a small amount of
grease).Slidethepumpassemblyintothetoiletbase
ensuringthemaceratorhousing is properlypositioned
withinthebase.
Thecut-outinthesideofthemaceratorhousingmust
alignwiththedischargeportinthebase(themacerator
housing is keyed so it will only go in when properly
positioned). Ensuring the O-ring is still properly
positioned in the O-ring groove in the seal housing,
placethepumpassemblyagainstthebaseandsecure
itinplacewiththefourscrewsandlockwashers.
Carefully lift the toilet and position over the two hold-
down screws using caution not to chip or break the
china. Securethe toilet down with the hold-downnuts
andwashersensuringtheplasticwasherisnexttothe
china.
Do not overtighten hold-down nuts.
5
5
11
10
9
8
17
12
13
14
15
16
18
19
20
21
22
23
25
FLUSH
FILL DRAIN
4A
4B
1
2
3
24
5
6
7
4C
EXPLODED VIEW
PARTS LIST
Qty. Part
Key Description Req. Number
1 Seat&Cover 1 37078-1000
2 Bowl,CompactSize,White 1 37076-0010
Bowl,StandardSize,White 1 37076-1010
Bowl,CompactSize,Bone 1 37076-2010
Bowl,StandardSize,Bone 1 37076-3010
3 BowlSpudand3/4"barbedadaptor 1 18753-0609
4 BowlInstallationHardware 1 18753-0604
4A TeeNut** 4
4B Washer,Plastic** 4
4C SocketHeadScrew** 4
5 Gasket* 1 37017-0000
6 BaseAssembly** 1 37004-1000
7 1-1/2"Adaptor,DischargePort 1 98023-0080
8 JokerValve*** 1 44106-1000
9 1"DischargePort** 1 37077-1000
10 Screw** 3 96050-0568
11 ChopperPlatewithLockNut
†
1 37056-1000
12 MaceratorHousing
†
1 37014-0000
13 CentrifugalImpeller
†
 1 37006-0000
14 SetScrew
†
1 18753-0492
15 O-ring*
†
1 43990-0066
Qty. Part
Key Description Req. Number
16 Seal
†
1 1040-0000
17 Screw
†
2
91010-0144
18 Washer,Plastic*
†
2 35445-0000
19 SealHousing
†
1 37043-1000
20 LockWasher#10,StainlessSteel
†
4
21 Screw
†
4
91027-0011
22 Slinger
†
 1 6342-0000
23 Motor-12VoltEMC
†
1 18753-0582
Motor-24VoltEMC
†
1 18753-0583
24 PAR-MAX4RinseWaterPump
12VoltEMC 1 30631-1092
24VoltEMC 1 30631-1094
25 SwitchPanel 1 37047-1000
ServiceKit 1 90197-0000
WastePumpAssembly
12VoltEMC 1 37072-0092
24VoltEMC 1 37072-0094
* PartssuppliedwithServiceKit.
**Partsincludedwithbase37004-1000.
†
PartsincludedinWastePumpAssembly
6
PAR-MAX SERVICE INSTRUCTIONS
The PAR-MAX rinse water supply pump needs no
periodicmaintenanceforproperperformance.Theonly
timeserviceworkshouldneedtobeperformedonthe
pump is if it should begin to leak water, suddenly
deliverslesswaterthannormalorshouldstoppumping
altogether.Shouldthepumpbegintoleakwater,itwill
be necessary to replace the diaphragm. If the pump
deliversa reduced rate of flowfrom normal or stops
pumping altogether, it will be necessary to either
removedebrisfromthepump’sflappervalvesorreplace
thevalvecageassembly.
NOTICE: Before performing any service, turn off the
electricalpowertothetoiletandrinsewaterpump.Take
precautiontoensureitisnotturnedonuntilserviceis
complete.Closetheinletfittingseacock.
It is generally easiest to remove the pump from its
installedpositionsothattheservicecanbeperformed
on a work bench.To do this, disconnect the electrical
wiresfromthemotorwireleads.Pushtheportretainer
clips back toward the pump motor and pull the port
fittings from the port sockets. Unscrew the four pump
mountingfastenersandremovethepumptoalocation
whereitcanbedisassembledwithoutlosinganyofthe
pumpcomponents.
Loosenthefour5/16"hex(slotted)machinescrewsin
the pump body and remove the body from the motor
and wobble plate housing (use care to not drop and
lose the port retainer clips and body retaining screws
and washers). The valve cage will now be exposed
whichcanbeeasilyliftedoffthediaphragm.Inspectthe
four outer inlet valves and central discharge valve to
ensuretheyseatsmoothlyagainstthevalvecage.
Lifttheouteredgesofeachvalvetomakecertainthere
isno debrislodged under anyvalve. Ifthere is debris
lodgedunderanyofthevalves,itwillcauseadiminished
flowrateorlossofflowentirely.Ifthevalvesdonotseat
smoothly against the valve cage, the valve cage
assembly should be replaced. If the pump has been
leaking,thediaphragmmustbereplaced.Removethe
four phillips head diaphragm retainer screws and
mushroom shaped diaphragm retainer caps. Remove
thediaphragmanddiaphragmhousingfromthemotor
and wobble plate housing. Inspect the wobble plate
bearing to make certain it is not corroded and still
rotatessmoothly.
With the new diaphragm positioned in the diaphragm
housing(ensuretheraisedsealingbeadsfaceoutward
awayfrom the motor) hold it against the wobble plate
withthefourretainingcapholesalignedwiththewobble
plate sockets. Push each diaphragm retainer cap
throughthediaphragmandintothesocketofthewobble
plate. Secure each retaining cap to the wobble plate
witha1"phillipsheadretainerscrew.Placethemotor
onitsrearendbellandpositionthevalvecageagainst
the diaphragm ensuring each cavities seal groove is
seatedonitssealingbeadmoldedintothediaphragm.
EnsuretheO-ringsealthatseparatesthepumpsintake
chamberfromthedischargechamberisproperlyseated
intheIDoftheraisedliparoundthecentraldischarge
valve.Whileholdingtheportretainerclipsintheirslide
grooves in the pump body, position the body on the
diaphragmandinsidethewobbleplatehousing.Secure
thepumpbodytothewobbleplatehousingwiththefour
2-1/4"machinescrewsandflatwashers.
Reinstall the pump to its mounting surface with four
fasteners through the rubber grommets. Ensure the
sealingO-ringisproperlypositionedoneachportfitting
and,withthe retaining clips slidback,push eachport
fittingintoitsrespectivesocket.
Slide each port retainer clip forward until it snaps
securelyintoitsseatedposition.Reconnecttheorange
motor lead to the positive supply wire and the black
motorleadtothenegativewire.
Ensuretheinletseacockisopenbeforerestoringpower
toandoperatingthetoilet.
ONE YEAR LIMITED WARRANTY
A. LIMITED WARRANTY: JABSCO warrants that at
the time of shipment, the products manufactured by
JABSCOandsoldhereundershallbeinconformitywith
applicable written specifications and descriptions
referred to or set forth herein, free from defects in
materialandworkmanship,merchantable,andsuitable
for a particular purpose, provided such is implied by
Statelawunderthecircumstancesofthissale.
B. WARRANTY ADJUSTMENT:
JABSCOagreestorepairorfurnishareplacement1.
for, but not to remove or install, any product or
componentthereofwhich,withinone(1)yearfrom
dateofpurchase,shallupontestandexamination
by JABSCO prove defective within the above
warranty.Receiptverifyingpurchasedateisrequired
toobtainadjustment.
BuyershallnotifyJABSCOofanydefectwithinthis2.
warranty no later than ninety (90) days after the
defectisdiscovered.
Noproductwillbeacceptedforreturnorreplacement3.
withoutthe priorwrittenauthorizationof JABSCO.
Upon such authorization, and in accordance with
instructions from JABSCO, the product will be
returnedtoJABSCO,shippingchargesprepaidby
Buyer. Products returned to JABSCO will be
addressedasfollows:
JABSCO
Cape Ann Industrial Park
Gloucester, MA 01930
Ortosuchalternatelocationsasmaybedesignatedon
the product, its container, or this sheet. Repair or
replacementmadeunderthiswarrantywillbeshipped
prepaidtoBuyer.
7
7
3
5
6
4
2
1
EXPLODED VIEW
PARTS LIST
Qty. Part
Key Description Req. Number
1 PortKit(1Pair) 1 30653-1004
2 BodyKit 1 30608-1001
3 ValveCage/ValveAssy. 1 30613-1001
4 DiaphragmKit 1 30617-1000
5 DiaphragmHousing& 1 30682-1000
RetainerCapKit
C. EXCLUSIONS FROM WARRANTY AND
LIMITATION OF LIABILITY:
Theforegoingwarrantyislimitedsolelyassetforth1.
herein and applies only for the period designated
above.
JABSCOSHALLNOTBELIABLEFORANYLOSS,2.
DAMAGE, SPECIAL OR CONSEQUENTIAL
DAMAGE OF ANY KIND, WHETHER BASED
UPON WARRANTY, CONTRACT, NEGLIGENCE,
ORSTRICTLIABILITYARISINGINCONNECTION
WITH THE SALE, USE, OR REPAIR OF THE
PRODUCT.
THE MAXIMUM LIABILITY OF JABSCO IN3.
CONNECTION WITH THIS WARRANTY SHALL
NOT IN ANY CASE EXCEED THE CONTRACT
PRICE FOR THE PRODUCT CLAIMED TO BE
DEFECTIVEORUNSUITABLE.
This warranty does not extend to any product4.
manufacturedbyJABSCOwhichhasbeensubjected
tomisuse,neglect,accident,improperinstallation,
or use in violation of instructions furnished by
JABSCO.
This warranty does not extend to or apply to any5.
unitwhichhasbeenrepairedoralteredatanyplace
other than JABSCO's factory, or by persons not
expresslyapprovedbyJABSCO,nortoanyunitthe
serial number, model number, or identification of
whichhasbeenremoved,defacedorchanged.
Components manufactured by any supplier other6.
thanJABSCOshallbearonlythatwarrantymadeby
themanufacturerofthatproduct.
This warranty applies to products defined as7.
“consumer products” by the Consumer Product
WarrantiesActasfromtimetotimeamended.
D. CONSUMER RIGHTS: This warranty gives you
specific legal rights, and you may have other rights
whichvaryfromstatetostate.Somestatesdonotallow
exclusionorlimitationofdamages.
STANDARD WARRANTY: Iftheproductsmanufactured
and sold hereunder are not Consumer Products, the
warranty extended to Buyer shall be as set forth in
subparagraphs (A), (B),and (C), EXCEPT THAT ALL
EXPRESS OR IMPLIED WARRANTIES OR
MERCHANTABILITY OR SUITABILITY FOR ANY
PARTICULAR PURPOSE ARE EXCLUDED.
Qty. Part
Key Description Req. Number
6 MotorKit12VdcEMC 1 18753-0577
MotorKit24VdcEMC 1 18753-0578
Motor/PumpAssy.12VdcEMC 1 30631-1012
Motor/PumpAssy.24VdcEMC 1 30631-1024
8
2-5/16
(59)
1-3/4
(44)
4-1/16
(103)
3-7/8
(99)
3-1/2
(89)
1-3/4
(44)
4-1/8
(105)
6
(152)
8
(203)
3-3/4
(95)
5/8
(16)
2
(51)
AB
C
D
E
1Dia
(25.4)
8-7/8
(225)
10
(254)
16-3/4
(425)
8-1/2
(216)
13-1/2
(343)
DIMENSIONAL DRAWINGS Inches (Millimeters)
Compact Size Bowl Standard Size Bowl
A 19-3/16(487) 19-3/16(487)
B 15-1/2(394) 15-1/2(394)
C 14-1/4(362) 17-1/4(438)
D 8-7/8(225) 8-7/8(225)
E 11-13/16(300) 11-13/16(300)
Orange
(Positive) Lead
Black
(Negative) Lead
1Dia
Form: 43000-0665-0803-GB Rev. 01/2009
USA
ITTCorporation
CapeAnnIndustrialPark
Gloucester,MA01930
Tel:(978)281-0440
Fax:(978)283-2619
UK
ITTIndustries
BingleyRoad,Hoddesdon
HertfordshireEN110BU
Tel:+44(0)1992450145
Fax:+44(0)1992467132
JAPAN
NHKJabscoCompanyLtd.
3-21-10,Shin-Yokohama
Kohoku-Ku,Yokohama,222-0033
Tel:+81-045-475-8906
Fax:+81-045-477-1162
ITALY
JabscoMarineItalia
ViaTommaseo,6
20059Vimercate,Milano
Tel:+390396852323
Fax:+39039666307
GERMANY
JabscoGmbH
Oststrasse28
22844Norderstedt
Tel:+49-40-535373-0
Fax:+49-40-535373-11
Warranty:Allproductsofthecompanyaresold,andallservicesofthecompanyareofferedsubjecttothecompany’swarrantyandtermsofsale,copiesofwhichwillbefurnisheduponrequest.
Detailscorrectattimeofprinting.Wereservetherighttochangespecicationswithoutpriornotice.
©Copyright2009ITTIndustries,RegisteredEnglandNo.81415,registeredofce:JaysCloseViablesEstate,Basingstoke,Hants,RG224BA
www.jabsco.com
/