JABSCO 37010 Series Quick start guide

Model 37010-Series

ELECTRIC MARINE TOI LET

Push Button Operation

FEATURES

• WhiteVitreousChinaBowlAvailableinTwoSizes

• BakedEnamelSeat&CoverinCompactor

HouseholdSize

• FlexibleImpellerFlushPump

• PermanentMagnetTypeMotor,FullyEnclosed,with

StainlessSteelShaft

• HighCapacityMaceratorandBowlScavengerPump

• Built-inBackFlowPreventer

• AllCorrosionResistantMaterialforMarineUse

VARIATIONS

VOLTAGE COMPACT SIZE HOUSEHOLD SIZE

12VdcEMC 37010-0090 37010-1090

24VdcEMC 37010-0096 37010-1096

INSTALLATION

TheJabscoelectrictoiletmaybeinstalledaboveorbelow

thewaterline.Flushpumpisself-primingwithaverticallift

up to 4 feet; discharge macerator pump can operate

againstaverticalheadupto4feet.

Inletandoutletseacocksshouldbeeasilyaccessibleand

be positive shut off valves. If seacocks cannot be

convenientlyoperatedfromtoiletlocation,installsuitable

shutoffvalvesforinletanddischargeconnections.

Base assembly may be moved 90° to accommodate

connectionsandprovideaccessibilityforservicing.

Surfacewheretoiletismountedshouldbeflattoprevent

distortionoftoiletbase.

PLUMBINGCONNECTIONS-Connectinlethoseusing

either5/8"or3/4"IDhose(asleeveisincludedtoadapt

pumpinletfrom5/8"to3/4").Makesureallinletconnections

areairtightandfreeofsharpbendsorrestrictions.

Connect 1" or 1-1/2" hose to discharge port (Adaptor

98023-0080 is included to convert discharge port to

1-1/2"IDhose),andmakesuitableconnectiontoholding

tank or other discharge system. Avoid sharp bends or

restrictions.

Forabovewaterlineinstallations,acheckvalvemayhave

tobeinstalledintheflushwaterintakelinetoensurerapid

pumppriming.Toretainwaterinbowl,makealoopinthe

dischargelineabout8inchesabovebaseofbowl.

DANGER

CAUTION

WARNING

Floodhazard.Anytoiletinstalledbelowthewaterline

orwhichmaybebelowthewaterlineatanyangleof

heelortrimmustbeintalledwithproperlypositioned

ventedloops.Failuretodosocanresultinflooding

whichcancauselossofpropertyandlife.

Do not connect the toilet to the vessels

potablewaterforitssourceofsupply.Todosocanresult

incontaminationofpotablewatersupply.Iffreshwateris

preferredforflushing,provideaseparatefreshwatertank

tosupplywatertothetoiletonly.

DONOTCONNECTINLETHOSETOAPRESSURIZED

WATERSYSTEM.

Ifthetoiletis,orcanbe,belowwaterlineatanynormal

(includingstatic)attitudeofvesselheeland/ortrim,a3/4"

VentedLoopFittingmustbeinstalledinthelengthofhose

connecting the flushing pump to the inlet seacock.The

VentedLoopFittingmustbepositionedsoitremainsslightly*

abovethewaterlineatallanglesofheelandtrim.

Insomeinstallationswhenaventedloopisinstalledinthe

intake hose, the flushing pump primeability and flow

characteristics are reduced and may adversely affect

toiletfunction.Torestorepumpperformance,connecta

solenoid valve (Jabsco No. 37068-2000) to the vent air

inlet to interrupt the air supply during the flush cycle.

Screwthe¼”brassconnectorontotheventedloopand

wire the solenoid in parallel with the toilet motor. See

Diagram1forinstallationandwiringillustration.

*Recommendedminimumheightabovewaterlineis6".

ELECTRICAL CONNECTIONS - Select a location for

theswitchandinstructionplate,makingsurewireleads

fromboththetoiletandpowersourcecanberoutedto

theswitch.Ensurethepanelwhereinstallingswitchis

no more than 1" thick. Drill a 5/8" mounting hole and

installswitchandinstructionplate.Usestrandedcopper

wireofthecorrectsize(determinedfromtheelectrical

specificationschart)toconnectonesideoftheswitchto

thepositivepowersource.Anappropriatesizefuseor

CAUTION

equivalent circuit breaker (determined from electrical

specifications chart) must be installed in the positive

power lead within seven inches of the power source.

Connect the other side of the switch to the orange

(positive) motor lead. Connect the black (negative)

motor lead to the negative side of the battery or

groundedbussbar.

NOTICE: Correct motor polarity (orange to positive,

black to negative) is important. Reverse polarity can

damage motor and void warranty. Full voltage at the

motorisrequiredtoproperlyoperatetheElectricToilet.

Thetoiletmustbewiredinacircuitindependentofall

otheraccessories.

ELECTRICAL SPECIFICATIONS

AMP FUSE WIRE SIZE PER FEET OF RUN*

VOLTAGE DRAW SIZE 0'-10' 10'-15' 15'-25' 25'-40' 40'-60'

 12Vdc 16 25 #12 #10 #10 #8 #6

 24Vdc 8 15 #16 #14 #12 #10 #10

*Lengthofrunistotaldistancefrompowersourcetoproductandbacktoground.

OPERATING INSTRUCTIONS

Make sure inlet and outlet seacocks are all open; push

button



tooperate.Operateuntilbowliscompletelyflushed

anddischargepumphasscavengedwaterfrombottomof

bowl.

The Jabsco electric marine toilet will provide years of

troublefree serviceif properly used.Itwillhandlewaste

andtoilettissue.ItwillNOThandlerags,sanitarynapkins

orhardsolidobjects.

Ifbowldoesnotpumpoutandbeginstofill,partiallyclose

inletvalveuntilbowlisclearedandcompletelypumped

out.Thenoperateforafewsecondswithbothvalvesopen

toclearentiretoiletanddischargesystem.Formaximum

safety,whentoiletisnotinuseorvesselisunattended,

closeboththeinletanddischargeseacocks.

Todrainforwinterlay-up,closeinletvalveandoperatefor

afewsecondsuntilallwaterispumpedout.

After long periods of non-use,toilet andpump maydry

out.Toeaseinitialstart-up,putaboutonequartofwater

inbowlandletstandawhilebeforeinitialuse.

DISASSEMBLY

DANGER

CAUTION

WARNING

Floodhazard.Closeinletandoutletseacockspriorto

disassembling toilet. Failure to do so can result in

floodingwhichcancauselossofpropertyandlife.

Disconnectpumpinginletanddischargehoses.Remove

fourscrews,KeyNo.25,pulloutcompletemotor,pump

andmaceratorassembly.Ifassemblydoesnotslideout

easily,pushforwardandpullbacksharplyseveraltimes

tofreemaceratorhousingfrombase.

Remove discharge port, Key No. 12, and joker valve.

Unscrewchopperplate,KeyNo.14,byturningcounter-

clockwise, facing plate. Prevent shaft from turning by

placing screwdriver in discharge port and locking

centrifugal impeller blade. Remove macerator housing.

Loosen impeller set screw and slide impeller off motor

shaft.

Removefourflatheadscrewsandtwowashers,KeyNos.

20,21,&22.Removetheplasticwearplate,KeyNo.23,

withsealingsleeve,KeyNo.19,andgasket,KeyNo.26.

Slidepumpassemblyoffmotorshaft.Replaceallwornor

damagedparts,cleanremainingparts.

ASSEMBLY

Presssealintobodywithlipfacingimpeller;becareful

nottococksealinbore.Installpumpbodyonmotorand

positiononregister.Lubricateimpellerborewithpump

greaseandinstallimpeller.Positionthegasketagainst

the body and install the wearplate ensuring the two

plasticsealingwashersareundertheheadsofthetop

andbottomscrews.NOTE:Thecurrentplasticwearplate

supercedestheearlierbrasswearplateandwithitthe

stainless steel wearplate is no longer used. Slide the

rubber sealing sleeve on the motor shaft and push it

into its recess in the wearplate. Relocate centrifugal

impeller on shaft, about 1/8" from the wearplate, and

tightenset screw.Place macerator housing over shaft

andcentrifugalimpeller,putlockwasheronendofshaft

and screw chopper plate on shaft and tighten. Install

O-ring in O-ring groove in wearplate surface, a little

greasewill help hold inplace,make sure inside body

surfaces are clean, line up slot in base with key on

maceratorhousing,slidepumpassemblyintobaseand

tighten with the fourscrews.Turnmotor on forone or

twosecondstobesurecentrifugalimpellerisfree.

NOTE:Theswitchonthesideof

the solenoid is inactive and will

notaffectoperation.

DISCHARGE

NEGATIVE

POSITIVE

NEGATIVE

VENTED LOOP

Heeled

Waterline

Static

VIEW A

SWITCH

INLET

VIEW A

VENT TO

ATMOSPHERE

1/4" BSP

BRASS

CONNECTOR

(Screws on to

Vented Loop)

Use PTFE tape

to seal

connector

onto Vented

Loop

ELECTRICAL

CONNECTIONS

Diagram1

PARTS LIST

Key Description Qty. Part Number

1 Seat,LidandHingeSet 1 

 CompactToilet  29097-1000

 RegularToilet  29127-1000

1A HingeSet(1Pair) 1 

 CompactToilet  29098-1000

 RegularToilet  29098-2000

2 Bowl,CompactSize 1 29096-0000

 Bowl,RegularSize 1 29126-0000

3&4 BowlSpud&Intake 1 29048-0000

 Elbow&O-ring

5 Clamp 1 18753-0044

6 Hose 1 29035-1001

7 BowlInstallationHardware 1 18753-0637

7A PhillipsHeadScrew** 4

7B Washer,Starlock** 4

7C HexNut**(twoplaces) 4

7D Washer,Plastic** 4

7E WasherStainlesssteel** 8

7F NutCap** 4

8 O-RingBowl/Seal 1 44101-1000

9 BaseAssembly** 1 37004-1000

10 1-1/2"Adaptor,DischargePort 1 98023-0080

11 JokerValve*** 1 44106-1000

12 1"DischargePort** 1 44107-1000

13 Screw** 3 96050-0568

14 ChopperPlate†withLockNut 1 37056-1000

15 MaceratorHousing† 1 37014-0000

16 CentrifugalImpeller† 1 37006-0000

17 SetScrew† 1 18753-0492

18 O-ring*† 1 43990-0066

19 SealingSleeve† 1 37036-1000

20 Screw† 2 91009-0096

21 Screw† 2 91010-0130

22 Washer,Fiber*† 2 35445-0000

23 WearplateKit‡† 1 37018-0000

24 LockWasher#10,StainlessKit† 4

25 Screw† 4 91027-0011

26 Gasket*† 1 12558-0000

27 FlexibleImpeller*† 1 6303-0003

28 Body† 1 12554-0000

29 Seal&Retainer*† 1 1040-0000



Key Description Qty. Part Number

30 Slinger† 1 6342-0000

31 Motors:

 Motor-12VoltEMC† 1 37064-0000

 Motor-24VoltEMC† 1 37065-0000

32 Adaptor 2 93003-0240

33 Switch&Plate 1 37020-0000

34 MotorCover† 1 43990-0051

35 ScrewCover(3each) 1 37003-1000

 ServiceKit  37040-0000

 Motor/PumpAssy.12VEMC†  37041-0010

 Motor/PumpAssy.24VEMC†  37041-0011

* PartsSuppliedwithServiceKit37040-0000.

** Partsincludedwithbase37004-1000.

‡ Wearplate#23includesSealingSleeve#19andPump/

BaseO-ring#18.

† PartsincludedinMotor-PumpAssembly.

EXPLODED VIEW

BOWL

ELBOW

DIMENSIONAL DRAWING

INCHES(MILLIMETRES)

A B C D E F G

COMPACTSIZEBOWL 19-3/4(493) 4-13/16(123) 13-13/16(351) 13-7/8(352) 17-3/4(451) 9-7/8(251) 7-5/8(194)

HOUSEHOLDSIZEBOWL 21-3/4(543) 5-11/16(148) 14-5/8(372) 14-3/4(375) 19-3/4(502) 11-1/4(286) 8-1/2(216)

D Overall Width

1 (25)

Dia

(102)

6 (152)

5/16

(8)

3-1/8

(79)

5/8 (16) Dia

2 Places

2 Leads - 11 (279) Long

12-15/16

10-7/8

3-1/2

(89)

7-3/8

(187)

2-1/2

(64)

3-7/8

(98)

(102)

5+3/8

(137)

5/8

(16)

MOTORCOVER

Form: 43000-0612 Rev. 01/2009

USA

ITTCorporation

CapeAnnIndustrialPark

Gloucester,MA01930

Tel:(978)281-0440

Fax:(978)283-2619

ITTIndustries

BingleyRoad,Hoddesdon

HertfordshireEN110BU

Tel:+44(0)1992450145

Fax:+44(0)1992467132

JAPAN

NHKJabscoCompanyLtd.

3-21-10,Shin-Yokohama

Kohoku-Ku,Yokohama,222-0033

Tel:+81-045-475-8906

Fax:+81-045-477-1162

ITALY

JabscoMarineItalia

ViaTommaseo,6

20059Vimercate,Milano

Tel:+390396852323

Fax:+39039666307

GERMANY

JabscoGmbH

Oststrasse28

22844Norderstedt

Tel:+49-40-535373-0

Fax:+49-40-535373-11

Warranty:Allproductsofthecompanyaresold,andallservicesofthecompanyareofferedsubjecttothecompany’swarrantyandtermsofsale,copiesofwhichwillbefurnisheduponrequest.

Detailscorrectattimeofprinting.Wereservetherighttochangespecicationswithoutpriornotice.

JABSCO 37010 Series Quick start guide

Related papers

Other documents