Sunricher RF+Bluetooth CCT Wall Mounted Remote User guide

Brand: Sunricher

Model: RF+Bluetooth CCT Wall Mounted Remote

Type: User guide

Sunricher RF+Bluetooth CCT Wall Mounted Remote lets you effortlessly control your lighting with dual RF and Bluetooth connectivity. It features two customizable scenes, dimming capabilities, and CCT (correlated color temperature) adjustment for creating the perfect ambiance. Easily pair it with Sunricher RF+Bluetooth receivers for seamless control of your lighting system.

RF+Bluetooth CCT Wall Mounted Remote 70200047

Click to turn on

paired light devices

Function introduction

Important: Read All Instructions Prior to Installation

Front side

Back side

Output RF+Bluetooth signal

Operation Frequency

Operating temperature 0-40°C

Relative humidity 8% to 80%

Dimensions 80x80x13.6mm

Product Data

Power Supply 3V(1xCR2450 battery)

Click to turn off paired

light devices

Brightness up button,

press and hold down to

increase light intensity

Control WW channel,

press and hold down

to increase WW and

decrease CW

Control CW channel, press

and hold down to increase

CW and decrease WW

Scene button 1, press and

hold down to save a scene,

click to recall the saved

Scene button 2, press and

hold down to save a scene,

click to recall the saved

2.4GHz

80 mm

Pair with RF+Bluetooth receiver

Note: one receiver can be paired with max 8 remote controls.

Prog.

RF+Bluetooth LED Receiver

Step 1:Do wiring the RF+Bluetooth receiver according to wiring diagram(please refer

to the instruction of RF+Bluetooth receiver that you would like to pair with.

Step 3:Click any button of the remote(e.g. button ), LED lights connected with the

receiver flicker means the receiver is paired with the remote successfully.

55.57 mm

71.20 mm

11 mm

Battery: CR2450

Before the first use, please open the battery

cover and remove the protective film

55.57 mm

71.20 mm

• Mesh network for further control distance, receivers can transmit signal to each other

• Each remote can control numerous receivers

• Each receiver can be paired to max. 8 remote controls

• The controlled receiver status can be quickly synchronized to the smart APP

• RF+Bluetooth CCT remote

• Transmission range between every two neighbor devices up to 30m

• Bluetooth low power consumption technology, long battery life

• Waterproof grade: IP20

• Control 1 zone of RF+Bluetooth receiver

• Enables to save and recall 2 scenes for each zone

• Easy & quick pairing to the RF+Bluetooth receivers by simply pushing the buttons

Brightness down button, press

and hold down to decrease

light intensity

WW CW

WW CW Step 2:Click the “Prog. Key” or “Reset” button on RF+Bluetooth receiver (or reset

power of the receiver 3 times continuously if the button is not accessible) to set it into

pairing to RF remote status

• This device contains a button lithium battery that shall be stored and disposed properly.

• If you think batteries might have been swallowed or placed inside any part of the body, seek

immediate medical attention

• DO NOT expose the device to moisture.

• Do not ingest battery, Chemical Burn Hazard

• This product contains a coin / button cell battery. If the coin / button cell battery is swallowed,

it can cause severe internal burns in just 2 hours and can lead to death

• Keep new and used batteries away from children.

• If the battery compartment does not close securely, stop using the product and keep it away

from children.

Safety & Warnings

The key part of this controller is a universal, standard size design switch element that can be integrated in

numerous frames by different manufactures as below list:

BERKER S1, B1, B3, B7 glass

GIRA Standard55, E2, Event, Esprit

JUNG A500, Aplus

MERTEN M-smart, M-Arc, M-Plan

Method 1:Stick 3M glue on the

back of the bracket and then stick

the bracket to the wall

Method 2:Screw the bracket

to the wall

After the bracket is fixed,clip

the frame and control part to the

bracket in sequence

2.Install the controller to wall(2 methods)

②Pull out the

battery insulator

① Use tool to open the

silicone gel battery cover

1.Remove battery insulator

③Install the silicone

battery cover back

Installation

an explosion;

– leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or

the leakage of flammable liquid or gas;

- a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable

liquid or gas.

CAUTION

Risk of explosion if the battery is replaced by an incorrect type

– replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some

lithium battery types);

– disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in

Sunricher RF+Bluetooth CCT Wall Mounted Remote User guide

Sunricher RF+Bluetooth CCT Wall Mounted Remote User guide

Sunricher RF+Bluetooth CCT Wall Mounted Remote User guide

Related papers

Other documents