jibe SR-SB9001K8-CCT Operating instructions

Brand: jibe

Model: SR-SB9001K8-CCT

Type: Operating instructions

The jibe SR-SB9001K8-CCT is a versatile device that combines CCT and RF+Bluetooth technology, allowing you to control your lighting with precision and convenience. With its 1-zone control capability and the ability to save and recall 2 scenes for each zone, you can easily create and access your desired lighting ambiance. The mesh network feature extends the control distance by enabling receivers to transmit signals to each other, ensuring seamless connectivity throughout your space.

RF+Bluetooth CCT Wall Mounted Remote 70200047

Click to turn on

paired light devices

Function introduction

Important: Read All Instructions Prior to Installation

Front side

Back side

Output RF+Bluetooth signal

Operation Frequency

Operating temperature 0-40°C

Relative humidity 8% to 80%

Dimensions 80x80x13.6mm

Product Data

• This device contains a button lithium battery that shall be stored and disposed properly.

• DO NOT expose the device to moisture.

Safety & Warnings

Power Supply 3V(1xCR2450 battery)

Click to turn off paired

light devices

Brightness up button,

press and hold down to

increase light intensity

Control WW channel,

press and hold down

to increase WW and

decrease CW

Control CW channel, press

and hold down to increase

CW and decrease WW

Scene button 1, press and

hold down to save a scene,

click to recall the saved

Scene button 2, press and

hold down to save a scene,

click to recall the saved

2.4GHz

80 mm

Pair with RF+Bluetooth receiver

Note: one receiver can be paired with max 8 remote controls.

Prog.

RF+Bluetooth LED Receiver

Step 1:Do wiring the RF+Bluetooth receiver according to wiring diagram(please refer

to the instruction of RF+Bluetooth receiver that you would like to pair with.

Step 3:Click any button of the remote(e.g. button ), LED lights connected with the

receiver flicker means the receiver is paired with the remote successfully.

55.57 mm

71.20 mm

11 mm

Battery: CR2450

Before the first use, please open the battery

cover and remove the protective film

55.57 mm

71.20 mm

①

silicone gel battery cover

Use tool to open the

1.Remove battery insulator

②Pull out the

battery insulator

③Install the silicone

battery cover back

Installation

• CCT remote

• Control 1 zone of RF+Bluetooth receiver

• Enables to save and recall 2 scenes for each zone

• Easy & quick pairing to the RF+Bluetooth receivers by simply pushing the buttons

• Mesh network for further control distance, receivers can transmit signal to each other

• Each remote can control numerous receivers

• Each receiver can be paired to max. 8 remote controls

• The controlled receiver status can be quickly synchronized to the smart APP

• Transmission range between every two neighbor devices up to 30m

• Bluetooth low power consumption technology, long battery life

• Waterproof grade: IP20

RF+Bluetooth

Brightness down button, press

and hold down to decrease

light intensity

WW CW

WW CW Step 2:Click the “Prog. Key” or “Reset” button on RF+Bluetooth receiver (or reset

power of the receiver 3 times continuously if the button is not accessible) to set it into

pairing to RF remote status

The key part of this controller is a universal, standard size design switch element that can be integrated in

numerous frames by different manufactures as below list:

BEKER S1, B1, B3, B7 glass

GIRA Standard55, E2, Event, Esprit

JUNG A500, Aplus

MERTEN M-smart, M-Arc, M-Plan

Method 1:Stick 3M glue on the

back of the bracket and then stick

the bracket to the wall

Method 2:Screw the bracket

to the wall

After the bracket is fixed,clip

the frame and control part to the

bracket in sequence

2.Install the controller to wall(2 methods)

jibe SR-SB9001K8-CCT Operating instructions

jibe SR-SB9001K8-CCT Operating instructions

jibe SR-SB9001K8-CCT Operating instructions

Other documents